Mcc Panel

This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled.

Features:

Simplex & Duplex pattern
Degree of Protection: IP-42 to IP-65
Painting: Powder Coating / Spray Paint / Epoxy Paint
Compartmentalized design eliminates risk to maintenance personal
Sufficient space for incoming and outgoing cables
Provided with buzzer & hooter during emergency
Separate Bus bar and cable chambers
Motor Control Center shall have hinged door with lockable arrangement
Motor Control Center Available with Aluminum / copper bus bar
Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz

Application:

These are widely used for:
Protection against electrical Short Circuit, overload and earth fault of the system
Control & monitoring of the entire electrical system of an industry / plant
Systematic power catering to various load of an electrical system
Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc.

We offer the following options and facilities:
ASTA certified bus bar systems (50 KA for 1 sec as standard).
Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required
Ingress protection up to IP 65
Wall mounting or floor standing
Top, bottom or special cable entry
Front or rear cabling access
Fixed, plug in or with drawable type
Full range of instruments and metering to customers requirements
Contactor, soft start and variable speed drives
Local or remote control
Wired to separate terminal chambers
Facilities for thermal imaging
Local or remote manual controls
Relay or PLC automatic controls
Alarm systems
Alarm annunciators
BMS interface
Special control systems to customers requirements

This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled.

Features:

Simplex & Duplex pattern
Degree of Protection: IP-42 to IP-65
Painting: Powder Coating / Spray Paint / Epoxy Paint
Compartmentalized design eliminates risk to maintenance personal
Sufficient space for incoming and outgoing cables
Provided with buzzer & hooter during emergency
Separate Bus bar and cable chambers
Motor Control Center shall have hinged door with lockable arrangement
Motor Control Center Available with Aluminum / copper bus bar
Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz

Application:

These are widely used for:
Protection against electrical Short Circuit, overload and earth fault of the system
Control & monitoring of the entire electrical system of an industry / plant
Systematic power catering to various load of an electrical system
Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc.

We offer the following options and facilities:
ASTA certified bus bar systems (50 KA for 1 sec as standard).
Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required
Ingress protection up to IP 65
Wall mounting or floor standing
Top, bottom or special cable entry
Front or rear cabling access
Fixed, plug in or with drawable type
Full range of instruments and metering to customers requirements
Contactor, soft start and variable speed drives
Local or remote control
Wired to separate terminal chambers
Facilities for thermal imaging
Local or remote manual controls
Relay or PLC automatic controls
Alarm systems
Alarm annunciators
BMS interface
Special control systems to customers requirements

This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled.

Features:

Simplex & Duplex pattern
Degree of Protection: IP-42 to IP-65
Painting: Powder Coating / Spray Paint / Epoxy Paint
Compartmentalized design eliminates risk to maintenance personal
Sufficient space for incoming and outgoing cables
Provided with buzzer & hooter during emergency
Separate Bus bar and cable chambers
Motor Control Center shall have hinged door with lockable arrangement
Motor Control Center Available with Aluminum / copper bus bar
Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz

Application:

These are widely used for:
Protection against electrical Short Circuit, overload and earth fault of the system
Control & monitoring of the entire electrical system of an industry / plant
Systematic power catering to various load of an electrical system
Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc.

We offer the following options and facilities:
ASTA certified bus bar systems (50 KA for 1 sec as standard).
Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required
Ingress protection up to IP 65
Wall mounting or floor standing
Top, bottom or special cable entry
Front or rear cabling access
Fixed, plug in or with drawable type
Full range of instruments and metering to customers requirements
Contactor, soft start and variable speed drives
Local or remote control
Wired to separate terminal chambers
Facilities for thermal imaging
Local or remote manual controls
Relay or PLC automatic controls
Alarm systems
Alarm annunciators
BMS interface
Special control systems to customers requirements

Any Type Of Lt Panel Mcc, Pcc Pdb, Apfc, Feeder Pillar

We manufacture as per customer drawing or as per customer requirement we use sheet metal with powder coating .For wiring we use standard rating wire .
The switch gear used in this as per customer requirement.

Most of commercial and industrial installations in the country have large electrical loads which are inductive in nature, such as motors, large machines, air conditioners, drives etc., which results in a lagging power factor. This means loss and wastage of energy and heavy penalties by electricity boards. However in case of rapidly varying and scattered loads it becomes difficult to maintain a high power factor by manually switching on/off

Power Distribution Board (PDB Panel) is used for electrical Power Distribution. In this ACB, MCCB, SDF, MCB etc. are the main equipments. Power Distribution Board offers Isolation and Short Circuit as basic protections. Other Protections like over current, Earth Fault, etc. are offered on case to case basis. Designing needs cable entry, access, site conditions, place of placement etc. information. Types Compartmentalized design for ACB, MCCB and SDF feeders , Non-Compartmentalized design for MCCB, MCB feeders , Single front with rear access , Single front without rear access , Double front with both access
As per customer requirement we design panel or as per customer drawings we manufacture panel.The switch gear used in this panel as per customize or standard.