Flat Sheet

Also known as grp sheet, which full name is fiberglass reinforced polyester (plastic) sheet. As a new material, greater than that of steel products and aluminum products in specific tenacity. Products in the ultra-low temperature or high temperature will not happen brittle fracture, deformation and to prevent heat transfer. For that, frp is widely used in so many industry. 2.Frp sheet features: A. High mechanical strength and good impact toughness B. Roughness surface and easy to clean C. Corrosion resistance, wear resistance, yellowing resistance, anti- aging D. High temperature resistance E. No deformation, low thermal conductivity, excellent insulation properties

Mould:840 Width: 900mm Effective width: 840mm Thickness: 0.8mm-3.0mm Length: customized Color: blue, green, translucent, dark blue, white

Mold: lg-840 Width: 900mm Effective width: 840mm Length: cutomized Thickness: 0.8mm - 3.0mm Color: blue, translucent, green, white, ect

Supplier: Fiber cement flat sheet, roofing sheet, MGO board, MGO roofing sheet, calcium silicate board/ceiling board, MGO board

Corrugated Sheet Roofing, Corrugations Corrugated sheet roofing material is widely available and easy to use. Corrugations should run in a straight line between the highest and lowest points, and at a right angle to the purlins (the intermediate supports). The overlaps (ends and sides) depends upon the sloop of the roof. Purlin spacing should suit the end laps required for the size of sheet to be used. Sheets should be laid so that the side overlaps are directed away from the prevailing wind. All purlins should be in one plane and parallel to each other. They should be properly anchored to the supporting superstructure. Ends of all sheets should be supported by purlins. The free overhang at the eaves should not exceed 300 mm. 8 mm diameter (min) hook bolts, crank bolts or coach screws, should be inserted through 10 mm diameter drilled holes.- NEVER PUNCHED - in the crown of the corrugations. Nuts or screws should be tightened lightly at first, and then tightened again when a dozen or more sheets have been laid. At intermediate purlins, they should not be tightened in an attempt to make the sheet rest on the purlins. A cat-ladder or roof board should always be used when working on a roof for safety of the person and to avoid damage to the roofing material. Installation of corrugated roof sheeting These notes are intended to cover the use and installation of corrugated roof sheets such as PVC, other plastics and bitumen fibre sheets. Although very different as materials and where they are used, they do have similar properties regarding flexibility and weight. One advantage of these corrugated materials is that it is far more rigid than a flat sheet of a similar type and thickness. This enables considerable savings in both weight and cost, it also makes the sheet relatively easy to handle. Generally all these types of material can be used either as roofing or vertical cladding. Most of these sheeting tends to be susceptible to condensation when used as cladding for outhouses etc. - being relatively thin they tend to have low thermal insulation properties. Condensation will be reduced if the interior of the structure is well ventilated.

Fiber cement cladding sheets Applications Fiber cement cladding sheets are specially designed for external cladding, semi-exposed & external lining applications. Applied on a ventilated fascade our fiber cement products are a strong, durable & lightweight material, which provides an attractive cost-effective solution for a wide variety of projects. Composition Fiber Cement cladding sheets belong to the new generation of asbestos free compressed & stabilized flat sheeting reinforced with mineralized cellulose fibers. The sheets are non-combustible & resistant to rot, fungus & vermin attack. Color / Finish Fiber Cement cladding sheets are available in many beautiful colors ranging from our â??Naturalâ?� earth-tone to our â??Treatedâ?� colors that resemble eggshell paint sheen. It is important to note that the non-uniformity along with fading of the color & the presence of little imperfections are considered a common characteristic of the product & is not a defect as the panels are like a natural stone & does not look like an artificial product with an unnatural surface. These characteristics do not constitute a warranty claim & will not be entertained as such. The sheet is through colored & has impermeability. The general resistance of the sheet to airborne pollutants can be enhanced by using the â??Treatedâ?� material. The â??Treatedâ?� sheets are coated with an alkali-resistant varnish using a UV polymerizing system, which makes the sheet resistant to graffiti. This treatment allows for and easily cleaned surface and will help the sheets maintain their beauty for many years.

Reinforced asbestos sheet The material compounded by choosing common white,grey,or black sheets based on the diffrent technical requirements and carbon steel flat or tanged sheet,coated with graphite powder,anti-adhesive Tanged reinforced insertioin Thickness:1.0 to 3.0mm Length :1000mm;500mm Width :1500mm;1000mm;500mm Flat adhesive bond insertion Thickness:0.8 to 3.0mm Length :1000mm;500mm Width :1500mm;1000mm;500mm

Supplier: FRP Fiberglass skylight roofing sheet, PVC roofing sheet, FRP flat panels

Supplier: Steel deformed bar, steel wire rod, PC wire, PC bar, wire rope, h beam, Ipe, ipeaa, angle steel/ channel steel/ flat bar, sheet pile, GI wire, annealed wire, cold drawn wire, twist wire, MS plate, checkered plate, GI/PPGI, roofing sheet, hollow sections, square pipe