The tkm 15 asymmetric enclosure provides typical angles needed for ceiling and wall mounting as well as for stage monitor operation. The loudspeakers high-frequency section comprises a 1-inch diaphragm compression driver coupled to a conical 80 degree waveguide constant directivity horn. A high-power 15-inch magnet cone drivers , mounted in an optimally vented enclosure, reproduces low frequencies. Specifications Frequency range 65hz~18khz Sensitivity 98db Spl(aes/peak) 123db Dispersion angle conical 80waveguide Impedance 8 Power hangdling(aes) 350w Power hangdling(peak) 700w Components one 15 inch bass drivers &one 1 inch compression neodymium planar wave driver Connectors 4 neutrik speakon nl4mp loudspeaker connectors Weight 32.9kg Speaker size 728*465*448mm Materials plywood Packing details carton Carton measurements 750*645*545mm Information of container 88pcs/20' 200pcs/40' 251pcs/40'hq.
F600 Power Amplifier Key Feature: * 2/3U high, heavy duty steel chassis * Modular construction for easy servicing * Symmetrical layout for even weight distribution * High efficiency toroidal power transformer * Oversized, high energy, linear power supply * 3 steps, Class H Audio topology * Stereo, parallel or bridged operation * Twin balanced inputs (Neutrik XLR connectors) * Dual Speakon and Binding posts outputs * High quality components used throughout * Dual, continuously variable speed fans * Efficient two sides cooling, the efficiency is better than back to front cooling * Active, signal, protect and critical indicators * Duraluminium, 8mm thick front-panel * Unobtrusive carrying handles * Voltage Gain: 35 or 40 dB . Specification: 8ohms Stereo Power(RMS): 2X300W 4ohms Stereo Power(RMS): 2X462W 8ohms Bridged Power(RMS): 968W Frequency Response(+o/-0.3dB, 1W/8ohms: 20Hz-20kHz, -3dB@135kHz Power Bandwidth(rated power at 4ohms 1%THD+N): 20Hz-20kHz, -. 1.1dB/+0dB TourClass Protection: ACL, IGM, AutoRamp, short circuit, DC voltage, turn-on/off transient, current inrush, sub/ultrasonic input THD+N (1kHz 1W ): -60dB Voltage Gain (rated power @ 8Ic): X35dB Input Sensitivity (rated power at 8Ic): 0.97V Input Impedance (balanced/unbalanced): 20KIc/10KIc S/N Ratio ("A"weighted, full power at 4ohms): 99dB Crosstalk ("A"weighted, full power@4ohms): >-63dB Class: 3 Step H Input Connectors (per channel): Female XLR (pin 2+, configurable for pin 3+). TRS (tip+) Output Connectors (per channel): 5-way binding posts or Speakon connectors (market dependent) Supply Power: 1320W Power Supply (factory configured): AC220V/230V, 50-60Hz Cooling: Two side panel variable speed DC fans, better than conventional cooling Controls: Front panel: 2 attenuators, power switch; Rear panel: Signal ground lift & mode switches. LED Indicators (per channel): Signal, Protect, Active, Critical Construction: Steel chassis, 16 gauge. Casting Aluminum front panel. Dimensions (HXWXD): 88X483X480mm (2U) Net Weight: 19.2kg Gross Weight: 23kg.
Our pro audio cases is a new packaging products aiming at the problem that the traditional simple packed in wooden cases cannot solve that high-tech products can't be effectively protected and poor mobility of in the long distance transportation. Particularly designed and manufactured for speakers and other similar sound equipments. These protective cases can offer comprehensive protection for speakers and make your performance completely fresh. Special offers such as with wheels or special lids are also availble from RK.
1. 500 W continuous program power capacity 2. 96dB Sensitivity 1w/1m 3. 57Hz ~3100Hz frequency response range 4. 2.5" high temperature voice coil 5. Kapton™ former for increased rigidity and thermal protection 6. Pressed cones to improve the high frequency response 7. Ideal for compact 2-way system.
Features: Twin 1" (25mm) HF horn: 106dB @1W, 1m (single cabinet); Consistent 120(-6dB) horizontal mid and HF pattern control; Passive or Bi-amp operation;Fast, integral rigging system with variable splay angles. Specifation: Stadium,middle and small scale performance system; Large-scale opera house,music hall; Entertainment center,conference center. FREQUENCY RESPONSE :85Hz-18kHz DRIVERS:"2*6.5""(165mm)/2"" voice coil woofer 1*1""(25mm) /1.7"" voice coil driver" RATED POWER:250W RMS,1000W peak SENSITIVITY:97dB 1watt/1 metre MAXIMUM SPL:121 dB continuous,127 dB peak IMPEDANCE:8 ohms nominal DISPERSION(-6dB):Horizontal covrage£º120¡ãVertical coverage£ºVaries,depending on array length and configuration CROSSOVER:800Hz, 2.5kHz passive CONNECTORS :2*Speakon Nl4 PACKAGE SIZE:380mm*280mm*635mm(1PCS) NET WEIGHT:14 kg.
Cla-110 line array speaker system 1) cla-110 line array is a high capability full range 2-way sound audio speaker. 2)its suit for many entertainment, live show and square which places have a high requirement. 3) its voice can spread wide range and far. 4) cla-110 line array uses 18mm birch plywood to construct its delicate and firm cabinet 5) special crane accessories make its more convenient to rigging. 6)small body but have a heavy shock voice. Dimensions(mm): w 580*d 400*h 310 Weight(kg): 25kg net, 28kg gross
* 1400 W continuous program power capacity * 97dB Sensitivity 1w/1m * 37Hz ~1800Hz frequency response range * 4" inside/outside voice coil with OFC(Oxygen-free Copper) wire for improved power-handling and durability * Optimized winding length for extended Xmax * Forced air ventilation and 14mm top plate for minimum power compression * Ideal for compact bass-reflex subwoofer application: 1. Nominal Diameter: 18 inch 2.Rated Impedance: 8 ohm 3.Nominal Power handling: 700 watts 4.Program Power: 1400 watts 5.Sensitivity(lw/lm): 97 db 6.Frequency Range 37-1.8 k hz 7.Minimum Impedance(Zmin) : 6.9 ohm 8.Voice Coil Diameter : 4 inch. 13 net weight.
Features: Stand alone vertically array able enclosure; Line array downfill element; Consistent 120¡ã(-6dB) horizontal mid and HF pattern control. Specifation: Multi-purpose hall,grand hotel,Sound reinforcement; Small-scale moving commercial performance,band sound reinforcement. Frequency Response :45Hz-18kHz DRIVERS:"8x5""(125mm)/1.5""(35mm) voice coil LF driver 4x1""(25mm) exit compression driver" RATED POWER:400W RMS,1600W peak SENSITIVITY:92dB 1watt/1 metre MAXIMUM SPL:118 dB continuous,124 dB peak IMPEDANCE:4 ohms nominal DISPERSION(-6dB):120¡ãx 40¡ã CROSSOVER:900Hz, 2.2kHz passive CONNECTORS :2xNeutrik Speakon NL 4 PACKAGE SIZE:(W)502mmx(D)412mmx(H)713mm NET WEIGHT:32.5 kg.
Features: Three-way line array element; Twin 1" (25mm) hf horn:- 106db @1w, 1m (single cabinet); Consistent 100¡ã(-6db) horizontal mid and hf pattern control; Passive or bi-amp operation; Fast, integral rigging system with variable splay angles; Factory controller presets for a wide variety of configurations Specifation: Stadium, middle and small scale performance system; Large-scale opera house, music hall; Entertainment center, conference center. Frequency response :55hz-18khz Drivers:"2x10""(250mm)/3""(75mm) voice coil woofer 2x1""(25mm) exit compression driver" Rated power:500w rms, 2000w peak Sensitivity:101db 1watt/1 metre Maximum spl:128 db continuous, 134 db peak Impedance:8 ohms nominal Dispersion(-6db):100¡ã*7.5¡ã Crossover:800hz, 2.1khz passive Connectors :2xneutrik speakon nl4 Package size:(w)1004mmx(d)506mmx(h)880mm/2pcs Net weight:41 kg/pc.
Features: High power - maximum spl 130db continuous, 136db peak (single unit); Superior bass impact - all horn design; Wide bandwidth 50hz-18khz+/-3db (single unit); True 90¡ã(-6db) horizontal mid and hf pattern control; Fast, integral rigging system with variable splay angles;common grid may be used for flying or ground stacking Specifation: Stadium, middle and small scale performance system; Large-scale opera house, music hall; Entertainment center, conference center. Frequency response :50hz-18khz Drivers:"2x12""(300mm)/3""(75mm) voice coil woofer 2x1.4""(36mm) exit compression driver" Rated power:600w rms, 2400w peak Sensitivity:102db 1watt/1 metre Maximum spl:130 db continuous, 136 db peak Impedance:8 ohms nominal Dispersion(-6db):90¡ãx 7.5¡ã Crossover:600hz, 1.3khz passive Connectors :2xneutrik speakon nl4 Package size:(w)1115mmx(d)590mmx(h)635mm/1pc Net weight:52 kg/pc.
Features: One 1.4" (36mm) HF driver: 106db @1w, 1m (single cabinet); Consistent 120¡ã(-6db) horizontal mid and hf pattern control; Passive or biamp operation; Fast, integral rigging system with variable splay angles; Factory controller presets for a wide variety of configurations Specifation: Stadium, middle and small scale performance system; Large-scale opera house, music hall; Entertainment center, conference center. Frequency response :60hz-18khz Drivers:"2x8""(200mm)/2""(50mm) voice coil woofer 1x1.4""(36mm) exit compression driver. Rated power:300w rms, 1200w peak Sensitivity:98db 1watt/1 metre Maximum spl:124 db continuous, 130 db peak Impedance:8 ohms nominal Dispersion(-6db):120¡ã*7.5¡ã Crossover:800hz, 2khz passive Connectors :2xneutrik speakon nl4 Package size:(w)860mmx(d)520mmx(h)768mm(2pcs) Net weight:28 kg/pc.
Model name HYR-8A HYR-10A Power RMS 100W 120W Power PEAK 200W 250W Frequency 47Hz-20KHz 43Hz-20KHz Sensitivity( 1w/1m )97dB 97dB Peak SPL 127dB 128dB LF system 1X8" Steel frame 1X10" Steel frame HF system 1X1" Titanium 1X1" Titanium Voltage 115V/230V 115V/230V Amplifier Normal-amplifier Normal-amplifier Cabinet material ABS ABS With LED Display Other special specifecations is available, data upon requests.
Description and Application W-210A is a line array speaker which is made of two 10'' neodymium woofers, two 2'' titanium neodymium compression drivers and high-performance low-distortion compression driver with innovative horn design of waves phase philosophy. It is a zero interfere line array with multi- speaker combined to produce accurate directivity and maximum dynamic impact. Wherever low frequency extension is required, a W-210A will integrate seamlessly with W-250A line array sub-bass system in a standard configuration. Each enclosure is equipped with rigging system, allowing flown array to be constructed rapidly and safely. W-210A is very versatile and scalable for a wide range of applications in touring performance, corporate and fixed installation fields. W-250A is dedicated high performance sub-bass system designed to augment the low frequency output of the W-210A, W-250A is a sub-bass enclosure which must be flown with W-210A. So its physical dimensions are identical to the W-210A and it is equipped with the same proprietary rigging system. It features with twin 15¡± neodymium woofers with magnet structure and suspensions engineered for maximum linear excursion Model W-210A/W-250A Type Line array system Line array sub-bass system(W-250A) Frequency Response 55Hz-20KHz 3dB 40Hz-150Hz 3dB(W-250A) Directivity index(Dl) 12(¡À2)1.2KHz-16KHz Power handing LF 500W(RMS)1000W(PEAK) HF 160W(RMS)320W(PEAK) 1200W(RMS)2400W(PEAK)(W-250A) Sensitivity LF 99dB(1W@1M) HF 108dB(1W@1M) 112dB(1W@1M)(W-250A) MaxS.P.L LF 127dB(PEAK/1M) HF 127dB(PEAK/1M) 143dB(PEAK/1M)(W-250A) LF section 2¡Á10"(260mm) neodymium woofer 75mm(3in)coil Components 2¡Á15"(380mm) neodymium woofers 100mm(4in)coil(W-250A) Nominal impedance 16 ohm 4 ohm(W-250A) HF section 2¡Á2"neodymium compression driver with 51mm titanium diaphragm Nominal impedance 16 ohm Output section 2-channel Dispersion pattern 110¡ãH¡Á9¡ãV Finish Water-proof,wear-resistant textured black paint Array design Arrays of less than 3¡ÁW-210A will provide poor dispersion control and are neither recommended nor supported Speaker cables LF 1(+)1(-) HF 2(+)2(-) 1(+)1(-) (W-250A) Rigging system Please refer to the W-210A user manual before any operation Input connectors 2¡ÁNL4MP speakon Recommend crossover LF 45Hz-1200Hz HF 1200Hz-20KHz 35Hz-120Hz(W-250A). Dimensions 855*293*600mm(W*H*D) 855*610*820mm(W*H*D)(W-250A) Package dimensions 925*360*670mm/0.22cbm 925*680*890mm/0.56cbm(W-250A) Enclosure Birch plywood Net weight 42kg (W-210A)/ 81kg (W-250A) Gross weight 45kg (W-210A)/ 84kg (W-250A).
Weatherproof PA speaker YT-520,a model of weatherproof speaker, is innovative and equisite with an excellent timbre.It can play with exacting precision in full range, especially a wonderful blend of sweetness, richness and detail in lows.Thanks to a high sensibility,sound pressure and its punchy performance,it makes a breakthrough in the traditional column and PA speaker,which onlyreproduce the mids and highs.And the sealed structure, allowing them to sustain any tough condition such as snowstorm,and the user-friendly with an adjustable 30 degree angle make it an instant hit in public or entertainment venues such as high class hotels,buidings,superstores,hospitals,schools,meeting rooms,auditoriums,exhibition center It's specification is as follows: Voltage: 70-100v Rms power:20w Sensitivity:92dB Frequency response:80Hz-18kHz Dimension:248x200x160mm Net weight:2.5kg CuFt/CTN:1.12 CBM/CTN:0.0317 QTY(pcs) 1x20'CY: 883 1x40'CY: 1830 1x40'HQ: 2145 Min Order:50 pcs
The vp series power amplifier offers clean, reliable power in a durable enclosure. If you need professional amplification performance, the vp series is perfect for delivering pure, consistent wattage night after night. With six models power upto 1200 watts, the vp series is ideal for powering pa systems and dj rigs. To ensure seamless, reliable performance, the amp features variable-speed cooling fans for thermal stability, along with short-circuit, thermal, over current, thermal protection. For connecting convenience, the vp series boasts xlr and speakon &banana binding post outputs. The unit also provides front panel indicators for signal, limit, protect and power, plus level controls for channels 1 and 2. Selectable modes for stereo and mono bridge give you even more flexibility. Selectable output power range to drive professional loudspeakers without clipping Variable-speed cooling fan for thermal stability and reliability Xlr balanced inputs and speakon &banana binding post outputs Limiter indicator for amp output protection Stereo and mono bridge Variable speed fan for low noise Comprehensive front panel indicators including signal, limiter, protect and power Dc output protection and short circuit protection Frequency response 10hz c 50khz at 1.5 db Total harmonic distortion: less than 0.05% Input sensitivity & impedance: 0.775v Signal to noise (20 hz - 20 khz) > 95db Shipping dimensions (wxdxh) 585x 580 x 165mm
19'' rack case for amplifiers and effects.Constructed with 9mm plywood glued with 1mm fireproof laminate, 1.5mm aluminium extrusion, recessed handles, recessed butterfly Catches, ball corners, casters etc.