Please quote for the following wholesale product requirement -
Product Name: Electrical Immersion Heaters
Specifications:
Qyt: 2 Units initially later LCL.( Relevant IEC Standards )
Note: The proposed supply shall comply with all the attached documents. Any deviations or exceptions shall be clearly identified and detailed in your quotation for our evaluation and approval.
Please note that the heater shell is not included in the scope of supply.
Electrical : SP-1103 & SP-1107
Process/mechanical : SP-2454
Supply Characteristics : as per DEP / deviations:
Allowed Total Harmonic Distortion (THD) : 6.5%
Rated Supply Voltage : 415 V ± 5%, 3-phase, 4-wire
Rated Frequency : 50 Hz ± 2%
Power Supply : 3 kW
Prospective short circuit current at PC : kA r.m.s; kA peak; or protected by fuse rated: A
Service conditions P&C Assembly : as per DEP (specify separately)
Service conditions Heater : as per DEP (specify separately)
Area Classification Heater : Zone 2 Temp class: T3 ;Gas group: IIB
Incoming switch required in P&C Assembly : yes ; key interlock: no
Unit Transformer : no; in scope of heater supplier : no
HV supply (if applicable) :N/A
Transformer data (if applicable) :N/A
Input signal : 4 - 20 mA
Transducers for remote metering : in the heater Suncover required : yes
Over-temperature control : via intrument inferface Cable size : incoming 4C x 16 sqmm M25 Gland *)
Type of fuses :DIN : outgoing 2 x 2 x 1.13 mm *)
Space heater in P&C Assembly : yes Space Heater cable size : 3C x 4 sqmm M20 Gland
Witnessed inspection/test required : no Cable entry : from below
Language on documents :English Cable gland plate : drilled
Language on equipment :English Glands required : yes
Gland type : 3/4" NPT (brass double compression)
Make and type :Vulcanic Flanged immersion Heater
Name / location nearest service organisation :Vulcanic - Spain (Torrelavega)
Maximum power requirements : 3 kW at pf:
Rated input current : A / phase Voltage : V
Maximum heater current : A
Peak inrush current : A
Transformer data (if applicable) :N/A
P&C Assembly space heater included : yes
Main terminal box space heater included : yes
Suncover over main terminal box : yes
Over-temperature devices :PT 100
Cooling : natural
Specified tender documentation attached : no
Detailed test protocol attached : no
Element material :SS 321
Flange Material :SS316
GDD150 box :SS316L No
All materials shall be in line with SP-2337 and SP-2454 S
PECIAL REQUIREMENTS AND REMARKS REMARKS ON REVISIONS
1. Heater is sized for 148 Nm3/hr of Air, Inlet minimum temperature: 5°C,
Outlet temperature: 54°C, maximum Air pressure 950 kPag.
2. Heater element dimensions: OD Head 204 mm, Heating element diameter 86mm, Heating element length 800 mm, Total length 1143 mm.
3. Heater shell dimension: OD 114,3mm (4"), Total lenght 996mm
4. Bellelli scope includes NPT to metric adapters for all cable glands.
Quantity Required : 1 Less than Container Load/LCL
Specifications :
Type: Electric Starter
for 6.5HP and 188F
Lithium Electric Starter Recoil Pull Start,electric Starter For Gasoline Generator Engine
Quantity : 20 Units Initially Later Lcl
HS Code: 851140
Please quote for the following wholesale product requirement -
Product Name: Electric Fireplaces
Specifications:
Heating power levels - ideally a first level around ** 750-1000 W
Hs Code 8516.29
Whether the ** flame effect can operate independently with the heater switched off
