Construction Chemicals Suppliers and Manufacturers

Its used in construction industry. For price, specifications and more details please contact us.

Polycarboxylate superplasticizer products have been extensively used in cement or gypsum-based mortars with high fluidity and high strength requirements. It is widely used in fluid mortars, such as fluid mortar for pouring, paving, and painting. For price, specifications and more details please contact us

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

Product Category- Construction Chemicals Product Name- Zoriscott Clear Water base Description of the product- Transparent coat for pavers and painted surface Area of Use (Application)- "1. Paver block, painted surface, mosaic tiles, vertical and horizontal painted walls 2. Easy application by brush or spray" Category (For Painters, Carpenters, etc.)- Contractors USP of the product- 1. Single component, ready to use concentrated liquid material 2. Excellent adhesion properties for ceramics 3. Excellent gloss with low dirt pick up" Area of application- Stones & Marbles

Product Category- Construction Chemicals Product Name- Scottproof 200 Description of the product- Filling of normal plaster cracks upto 5mm wide Area of Use (Application)- Concrete and plasters Category (For Painters, Carpenters, etc.)- Contractors USP of the product- 1. Remarkable improvement in flow and workability 2. Most economical waterproofing additive for plaster and concrete 3. Reducing water cement ration an increases the compressive strength" Area of application- Concrete & Plaster

Product Category- Construction Chemicals Product Name- Rapidite Description of the product- For extra rapid setting Area of Use (Application)- All plaster and mortar Category (For Painters, Carpenters, etc.)- Contractors USP of the product- 1. Quick setting 2. Rapid hardening and waterproofing compound for cement/concrete" Area of application- Plaster

Product Category- Construction Chemicals Product Name- Plaxem Description of the product- Admixture for concrete with waterproofing properties Area of Use (Application)- Concrete and plasters Category (For Painters, Carpenters, etc.)- Contractors USP of the product- 1. This product is designed to give most satisfactory waterproofind performance even in poorly graded cement/concrete mix. Its highly economical 2. Increases workability and cohesiveness of the mix 3. Reduces water cement ratio and increases the compressive strength" Area of application- Concrete

Product Category- Construction Chemicals Product Name- Krack seal XL Description of the product- Filling of normal plaster cracks upto 5 mm wide Area of Use (Application)- Internal and external plastered brick masonry surfaces wall cracks of upto 5 mm width Category (For Painters, Carpenters, etc.)- Contractors/Painters USP of the product- 1. Flexible & UV resistant, does not crack, accomodates minor movements in cracks 2. Over coatable after 24 hrs by any type of polymer based paints 3. Excellent adhesion with cementitious surfaces" Area of application- Interior & Exterior

Product Category- Construction Chemicals Product Name- Krack seal Powder Description of the product- Filling of normal plaster cracks upto 2mm wide Area of Use (Application)- Repairing of internal and external cracks in plastered surfaces upto 5mm size Category (For Painters, Carpenters, etc.)- Contractors/Painters USP of the product- 1. Strong adhesion to common building substrated 2. Does not contain solvent thus no emission of vapors 3. Acts as a surface leveller before painting, it reduces paint consumption and increases the life of the paint, making it economical" Area of application- Interior & Exterior