Quantity Required:
1,000 - 50,000
Pieces
Payment Terms:
Bank Transfer/ LC
Destination:
Austria, Austria
Looking for suppliers from:
Worldwide
Please quote for the following wholesale product requirement -
Product Name: Perforated Sheet Like Like Stainless Steel Perforated Sheet
Specifications:
Part: Flat, Round Perforated Disc (Screen). Visible Part Of A Consumer Water-Sports Product; Permanent Contact With Fresh And Salt Water.
Outer Diameter: 30.0 mm, Tolerance Plus Or Minus 0.1 mm
Thickness: 0.5 To 1.0 mm; Supplier May Propose The Most Economical Standard Gauge Within This Range
Holes / Aperture:
Hole Shape: Free: Round, Square Or Polygonal (E.G. Hexagonal)
Hole Size: 0.5 / 0.6 / 0.8 mm (Diameter Or Width Across Flats; 3 Variants - Please Quote Each One You Can Produce; Plus Or Minus 0.05 mm)
For Woven Mesh: Equivalent Aperture 0.5 To 0.8 mm
Pattern: Regular Grid Over The Full Face, Square Or 60 Degree Staggered At Supplier's Choice; Maximum Open Area. Approx. 300 To 600 Holes (Round); Exact Count Not Critical. Plain Rim Up To 1.5 mm Acceptable - Please State.
Flatness / Edges: Flat Within 0.2 mm. Burr-Free On Both Sides, No Sharp Edges, No Loose Wires Or Fraying (Woven Mesh: Sintered, Calendered Or Edge-Secured).
Surface: Decorative Quality On One Side: Uniform Finish, No Scratches, Stains, Heat Tint Or Oxide. Clean And Oil-Free. Please State Finish (E.G. Pickled/Passivated, Electropolished, Anodised).
Accepted Manufacturing Routes And Materials (Please Offer Your Most Economical Combination; Alternatives Welcome):
Route A: Woven Wire Mesh - Disc Punched Or Laser-Cut From Woven / Sintered Mesh
Route B: Punched Sheet - Perforated Sheet, Disc Blanked; Please Confirm Min. Hole Diameter Vs. Thickness
Route C: Laser-Cut Sheet - Holes And Contour Laser-Cut; No Dross, No Discolouration
Route D: Alternative - E.G. Photo-Chemical Etching Or Electroforming Welcome If Cheaper In Series
Material (Seawater-Resistant):
Grade / Condition:
Stainless Steel - Preferred 1.4404 / AISI 316L (Or 1.4401 / 316); 304 Not Accepted
Aluminium EN AW-5754 / 5083 (AlMg), Anodised
Bronze CuSn6 / CuSn8 (Phosphor Bronze)
Brass Dezincification-Resistant Or Seawater Grade Only
Commercial and quality requirements • Prices in EUR, net, per piece, per quantity break; validity min. 90 days. Please state MOQ and price basis for material surcharges. • Delivery: DAP 9062 Moosburg, Austria (Incoterms 2020); alternatively FCA with estimated freight. State country of origin and HS code. • Samples: 5 pcs from the intended series process and material, with measurement report (Ø, thickness, hole size). Series order follows sample approval. • Payment terms: please state. Non-EU suppliers: please state export documents provided. • Documents: material certificate EN 10204 - 3.1 for series lots (2.2 for samples); RoHS and REACH compliance declaration. • Packaging: scratch-protected, clean and dry, bulk in sealed bags or layered; labelled with part name, quantity and lot number. • Supply: annual demand according to sales; call-off orders or blanket order possible - please state conditions. • Quality: ISO 9001 or equivalent preferred; 100 % free of burrs and visual defects (AQL proposal welcome).
Quantity (per order lot) 5 pcs test samples 1,000 pcs 5,000 pcs 10,000 pcs 50,000 pcs
Quantity Required : 1000 - 50000 Piece/Pieces
Shipping Terms : CIF
HS Code : 731419
Destination Port : Austria, Austria
Payment Terms : Bank Transfer/ LC
Looking for suppliers from : Worldwide
Contact : Klaus Ruetz
