Buyer is interested to receive quotations for the following RFQ -
Product Name: Bredent Dental Implant Abutments
Specifications:
• Compatibility: Must be compatible with main BREDENT dental implants
• Material: Ti6Al4V-ELI
• Size: Various sizes available to fit different BREDENT implant systems and platforms
• Certification: CE and ISO certified would be a plus
• Packaging: bulk
**Service Requirements:
• Warranty: Minimum one-year warranty on all abutments
• Delivery: Prompt delivery from STOCK
• Support: for long term co-operation, all defective parts should be replaced. We always perform 100% quality check for arriving parts
Quantity Required : 1 Less than Container Load/LCL
Please provide a quotation to the following requirement from importer -
Product Name: Bredent Dental Implant Abutments
Specifications:
**Product specifications:
• Compatibility: Must be compatible with main BREDENT dental implants
• Material: Ti6Al4V-ELI
• Size: Various sizes available to fit different BREDENT implant systems and platforms
• Certification: CE and ISO certified would be a plus
• Packaging: bulk
**Service Requirements:
• Warranty: Minimum one-year warranty on all abutments
• Delivery: Prompt delivery from STOCK
• Support: for long term co-operation, all defective parts should be replaced. We always perform 100% quality check for arriving parts
Quantity Required : 1 Less than Container Load/LCL
Specifications:
Hik OEM 4MP 5MP 6MP 8MP Outdoor Turret Bullet Dome Motion Detection Two Way Audio Network Camera 4K Poe IP Camera
Category:
Network Camera
Quantity: 100 Piece/Pieces
Please provide a quotation to the following requirement from importer -
Product Name: Collaborative Industrial Robots
Specifications:
Quantity 2 robots
for Overhead Rail-Mounted Automated Warehouse
Robots will perform picking, placing, transfer and recovery operations in a narrow warehouse environment.
The robots will be mounted on a fixed overhead linear rail and must operate reliably 24/7.
2. WORKING ENVIRONMENT (FIXED CONDITIONS)
Indoor warehouse, steel structure
Internal clear height: 2700 mm (floor to ceiling)
Linear rail mounted directly under the ceiling
No vertical (Z) axis on the rail system
3. STORAGE LAYOUT
3.1 Central Rack
Longitudinal central rack - Width: 600–700 mm
Height: NOT fixed
Final height must be calculated by supplier
Height depends on:
- rail system height
- robot body height
- safety clearance
Estimated usable rack height: approx. 1800–2100 mm
3.2 Side Racks
Left and right side racks
From floor level up to maximum usable height
Open bins with partial front wall (anti-drop lip)
3.3 Aisles
Left aisle: small / very small parts
Right aisle: medium / large parts
4. ROBOT SYSTEM ARCHITECTURE (MANDATORY)
Quantity: 2 robots
Robots must be 100% identical
Type: Collaborative industrial robots
Axes: 6-axis
Mounting:
- Robot base mounted on a moving carriage
- Carriage runs on a fixed overhead linear rail
Rail configuration:
- One common rail for both robots
- Rail mechanically splits into two independent park branches - Park A / Park B
Critical requirement
No robot may physically block the other robot, including in fault or emergency conditions.
5. FUNCTIONAL REACH REQUIREMENT (NO FIXED NUMBERS)
The robot reach must be calculated and demonstrated by the supplier.
Each robot must be able to reach and operate in all of the following positions without collision:
5.1 Vertical Coverage
From floor level (0 mm)
Up to the highest usable rack level on:
- side racks
- central rack
5.2 Lateral Coverage
From the rail centerline, robot must reach:
- left aisle
- right aisle
Robot must pass over at least half of the central rack width
Minimum lateral offset: 300–350 mm
5.3 Oblique Access (Mandatory)
Robot must be able to:
- approach bins at an inclined angle
- pick parts from bins with partial front walls
Vertical-only picking is not acceptable
5.4 Supplier Obligation
Supplier must provide:
- Reach envelope
- Collision-free motion paths
- 2D/3D simulation proving:
- floor-level picking
- upper-level picking
- left/right aisle access
- oblique bin access
Offers without reach simulation are not acceptable.
6. ROBOT TECHNICAL REQUIREMENTS
Collaborative industrial robot
Payload (nominal): = 12 kg
Payload (max parts): 10 kg
Repeatability: ±0.05 mm or better
Continuous operation: 24/7
Approved for:
- overhead mounting
- inverted or suspended installation (manufacturer confirmation required)
7. SAFETY REQUIREMENTS
Force limiting
Safe torque
Safe stop
Collaborative operation according to international safety standards (CE / ISO)
8. PARTS TO BE HANDLED
Weight range: from grams up to 10 kg
Types:
- metal parts
- boxes
- bags
- irregular shapes
Orientation: random inside bins
9. INTERFACE WITH CONVEYORS
Pick & place to/from conveyor zones
Digital I/O or industrial fieldbus interface
Placement accuracy requirement: ±2 mm
10. REDUNDANCY & FAULT HANDLING (MANDATORY)
Robots must be fully interchangeable
In case of robot failure:
- faulty robot automatically moves to its own park position
- second robot continues operation and covers full working area
11. INTERFACE WITH LINEAR RAIL (PROVIDED SEPARATELY)
The robot must:
- Be suitable for mounting on a moving linear carriage
- Support cable routing via energy chain
- Support external axis synchronization
- Provide standard mechanical flange and electrical interfaces
12. DELIVERABLES REQUIRED WITH QUOTATION
Suppliers must include:
Full robot datasheet
Confirmation of overhead /
