Request an online quotation for Construction Rolls via our website at indevcogroup.com/building-construction/construction-film/ For users of construction and building films, our high-quality Construction Rolls are practical for protecting personnel and construction equipment. Our cost-effective PE Films are used for the protection of windows, doors, floors, sanitary equipment, radiators, seals, pipes, cables, insulation & floor coverings during indoor completion works. We also produce Concrete Curing Film & under Slab Vapor Barrier.
Bleached kraft or unbleached kraft paper with PE coating, is applied extensively in food packaging, medical packaging, and many other industries. We supply papers in roll and sheet with wide range of substance from 30-120gsm depending on your requirement, which can be either blank/plain or printed. Authorities certification in relation to food packaging is availabe at your request. and any other paper products with PE coating are available as well, for instance paper cups...
Excavators.
Electronic hardware as well as construction materials and equipment..
Construction, and minerals, sesame seeds, soybeans, groundnuts, grains and hibiscus flowers. granite slabs, ceramic tiles, as well as minerals like iron ore, lead ore, zinc, and beryllium among others..Sourcing high quality products, negotiating favorable terms with suppliers, managing logistics and shipping
Led bulb, tube light, panel light, decoration light, wall light, steel wires, steel plate, stainless steel plate, twisted wire rods, galvanized wires, wire mesh, site fencing, mosquito mesh, thread rods, rebar, twisted rods, t bar, nuts and bolts, hardware, pvc pipes, upvc pipes, api pipes, melamine, mdf board, plywood, film faced, shuttering, packing, core veneer, face veneer, hdf molded door skin, door filler, tubular particle boards, pvc boards, wpc boards, doors, block board, hard board, gypsum board, canopy, carpet, flooring wooden, bamboo, laminated engineering, tiles, granite tiles, granite blocks, black galaxy, wash basin, water closets, washbasins, ss sinks, faucets, furniture, pvc edge bending, crew, locks, pvc seals, silicone cartridges, shower enclosures, shower door hinges, handles, knobs, brackets, slides, nails, solar panels, flexible solar panels, solar power station, battery, inverters, rechargeable fans, lights, spring, 3ply disposable face mask, oxygen concentrator ,.Buying office, oem, components sourcing, value added services
Hollow Plastic Concrete Formwork for fundational building Size:1220*2440mm Thickness:15mm/18mm/20mm MOQ:100pcs Advantage:Reusable Application:concrete panels building formwork Color:Grey Weight:31kgs Quick Details: Product Name:Plastic concrete formwork Application:Concrete panels building formwork Material:PP plastic material Surface:Cleanly ,Glossy and smoothy Size: 1220*2440mm Thickness: 15mm, 18mm,20mm Type: Construction formwork Color: Grey Certificate: ISO9001:2008 Weight: 31KGS Packaging & Delivery Selling Units:Single item Single package size: 244X122X2.0 cm Single gross weight:31.0 kg Package Type:carton box packing onto wooden pallet Lead Time : Quantity(Piece)1 - 200201 - 336337 - 810>810 Est. Time(days)5715To be negotiated
Used construction machinery, excavators, dozers, cranes, backhoe loaders, access platforms, boom lifts, dumpers, telescopic handlers.
We make customized rolling, sliding gates, collapsible gates for home, commercial building factories etc. These gates come in Aluminum, Stainless Steel or in Steel. The surface is powder coated to last many years after installation. These gates can be installed on tracks or without tracks. Every aspect of the gates can be customized. These gates are easy to operate with minimal effort. Our standard dimensions Height 1600mm (height can customized) Stretching ratio: 1:0.17 + 0.42 (can be customized) Gate Minimum length :2 Meters Gate Maximum length: upto 90 meters ( double Gates) Operation: Hand operated, Motorized. Colors available: Blue, Red (colors can be customized) Please contact us for competitive pricing.
Steel/steel coils/steel billets/steel rod
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
MATERIAL : LDPE/LLDPE repro pellet film grade CATEGORY : LDPE/LLDPE TYPE : repro pellet GRADE : film grade SPECIFICATION : LDPE repro pellet,made from clean PE roll and film.Japan origin.Best for film maker.MFI 1 and MFI 4 , 1 full container (25 tons) for each grade. datasheet included Origin : JP - Tokyo LOADING WEIGHT: 25 Ton FAS (USD/Ton) : 1200$ Packaging : Jumbo Bag Est. Shipping Time: 15, 30, 45 days