Oil window: The oil viewing window located on the side of the water pump iseasy to inspect and the oil level is easy to repair. High and low pressure water seal components The high and low pressure dual water seal design of the"U" type "Buna N" material enhances the performance of thewater pump and improves its service life. The plunger support guide ringensures the coaxiality of the plunger, extending the service life of the waterseal and plunger. Pump head assembly: Selected forged brass material, high strength, no porositydefects, long service life, high pressure resistance, stable operation,reinforced 6-bolt fastening, 10mm, grade 8.8. Check valve assembly: The valve cage is made of specialmaterials that are sturdy and durable. The stainless steel 303 and 404 poppetvalves and springs, as well as the brass valve seat and cover, are sturdy anddurable, extending their service life. Pommel Precision machined hard solid ceramic plunger, sturdy anddurable. Crank Axle Accurate rounded corners and process treatment ensure durabilityand service life. Oil seal and O-ring A better crankcase oil sealing system, with stainless steelsprings for oil seals and O-ring seals to ensure sufficient tension. Bearing The positioning of large-sized bearings and snap rings ensuresthe concentricity of the crankshaft connecting rod, ensuring stable operationof the water pump. Bearing Block Precision machining ensures coaxiality and concentricity. Plunger Connecting Rod The high-quality alloy connecting rod has high load strength,durability, and stable operation. Crankcase The surface of the crankcase that has been oxidized by precisioncasting is a classic streamline design.
The horizontal slurry pump is a cantilever centrifugal slurry pump, which is suitable for conveying abrasive or corrosive slurry and is widely used in metallurgy, mining, petroleum, chemical industry, coal, electric power, transportation, river dredging, building materials and municipal engineering and other departments. For PHJ pumps, the wetted parts of the pump are made of rubber materials. Its pump body, pump cover and transmission parts are the same as PH pumps; it is suitable for conveying fine particles and corrosive slurry.
The horizontal slurry pump is a cantilever centrifugal slurry pump, which is suitable for conveying abrasive or corrosive slurry and is widely used in metallurgy, mining, petroleum, chemical industry, coal, electric power, transportation, river dredging, building materials and municipal engineering and other departments. For PHJ pumps, the wetted parts of the pump are made of rubber materials. Its pump body, pump cover and transmission parts are the same as PH pumps; it is suitable for conveying fine particles and corrosive slurry.
PPM series froth pump is a new generation of product developed by our factory on the basis of absorbing and assimilating advanced technology at home and abroad. It is widely used in metallurgy, mining, coal, chemical and other industrial sectors. Suitable for transporting abrasive or corrosive slurry containing foam, this series of pumps can effectively eliminate foam in the slurry during operation. It can still work normally in the case of insufficient incoming material, especially suitable for various flotation processes, and is an ideal product for transporting foam slurry.
PPM series froth pump is a new generation of product developed by our factory on the basis of absorbing and assimilating advanced technology at home and abroad. It is widely used in metallurgy, mining, coal, chemical and other industrial sectors. Suitable for transporting abrasive or corrosive slurry containing foam, this series of pumps can effectively eliminate foam in the slurry during operation. It can still work normally in the case of insufficient incoming material, especially suitable for various flotation processes, and is an ideal product for transporting foam slurry.
PPM series froth pump is a new generation of product developed by our factory on the basis of absorbing and assimilating advanced technology at home and abroad. It is widely used in metallurgy, mining, coal, chemical and other industrial sectors. Suitable for transporting abrasive or corrosive slurry containing foam, this series of pumps can effectively eliminate foam in the slurry during operation. It can still work normally in the case of insufficient incoming material, especially suitable for various flotation processes, and is an ideal product for transporting foam slurry.
PPM series froth pump is a new generation of product developed by our factory on the basis of absorbing and assimilating advanced technology at home and abroad. It is widely used in metallurgy, mining, coal, chemical and other industrial sectors. Suitable for transporting abrasive or corrosive slurry containing foam, this series of pumps can effectively eliminate foam in the slurry during operation. It can still work normally in the case of insufficient incoming material, especially suitable for various flotation processes, and is an ideal product for transporting foam slurry.
PPM series froth pump is a new generation of product developed by our factory on the basis of absorbing and assimilating advanced technology at home and abroad. It is widely used in metallurgy, mining, coal, chemical and other industrial sectors. Suitable for transporting abrasive or corrosive slurry containing foam, this series of pumps can effectively eliminate foam in the slurry during operation. It can still work normally in the case of insufficient incoming material, especially suitable for various flotation processes, and is an ideal product for transporting foam slurry.
PPM series froth pump is a new generation of product developed by our factory on the basis of absorbing and assimilating advanced technology at home and abroad. It is widely used in metallurgy, mining, coal, chemical and other industrial sectors. Suitable for transporting abrasive or corrosive slurry containing foam, this series of pumps can effectively eliminate foam in the slurry during operation. It can still work normally in the case of insufficient incoming material, especially suitable for various flotation processes, and is an ideal product for transporting foam slurry.
PPM series froth pump is a new generation of product developed by our factory on the basis of absorbing and assimilating advanced technology at home and abroad. It is widely used in metallurgy, mining, coal, chemical and other industrial sectors. Suitable for transporting abrasive or corrosive slurry containing foam, this series of pumps can effectively eliminate foam in the slurry during operation. It can still work normally in the case of insufficient incoming material, especially suitable for various flotation processes, and is an ideal product for transporting foam slurry.
Multiple Protections Dry run protection  Phase loss protection  Overloadno load protection  Short circuit protection  Overvoltage protection  Pump stalledantiseizing protection  Undervoltage protection  Pump shaft rust protection Major Features 1Pressure control electric contact pressure gauge or pressure switch 2Water level control probe or float switch 3Multifunction display visualization of voltage motor current upperlower tank status and alarms 4Upper tank for water supply control and lower tank for drainage control 5Operation mode AUTOMANUAL switch 6Fault indication fault trackinglast 10 fault reason displayaudiolight alarms 7Anticard protectionlongterm nonuse of the pump 15 days to start once 8Setting protection current for motor overloadnoloadnoload delay restart time adjustable 9Automatic restart when voltage comes to normal rating after overvoltageundervoltage protection 10Automatic restart after power failure recovery 11Time setting ONOFF 12Push button for adjustments and set up from display 13Restore factory setting press both Overload and NOLoadfor 3 seconds 14Automatic restarting pump from dry runningrestart time range 0999 minutes adjustable
brands: rexroth, HAGGLUNDS, AVENTICS, Danfoss, Parker, MOOG, sunhydraforce, EOWARDS, Leybold, INFICON. Products: plunger pump, solenoid valve, gear pump, vane pump, direction valve, servo valve, proportional valve, hydraulic valve, hydraulic pump, etc
Replace BUSCH Vacuum Pump Oil Mist Filter 0532140157/V532140157 Applied to R5 / RA / RC 0063 B R5 / RA / RC 0040 B R5 / RA / RC 0025 B R5 / RA / RC 0100 E R5 / RA / RC 0100 C R5 / RA / RC 0063 C R5 / RA / RC 0040 R5 / RA / RC 0025 R5 / RA / RC 0063 R5 / RA / RC 0063 E R5 / RA / RC 0100 R5 / RA / RC 0100 B
Replace BUSCH Vacuum Pump Oil Mist Filter .Applied to R5 / RA / RC 0250 C R5 / RA / RC 0205 D R5 / RA / RC 0160-132 R5 / RA / RC 0160 R5 / RA / RC 0160 B R5 / RA / RC 0302 D R5 / RA / RC 0202 D R5 / RA / RC 0255 D R5 / RA / RC 0250 R5 / RA / RC 0250 B R5 / RA / RC 0165 D R5 / RA / RC 0160-116 R5 / RA / RC 0160 C Eva CB 0250 R5 / RA / RC 0250 D R5 / RA / RC 0305 D R5 / RA / RC 0160 D R5 / RA / RC 0250-116
A continually increasing number of applications in industry and research are relying on vacuum technology. Thus widely differing requirements result regarding the vacuum generating systems. Based on the long-standing experience in the design and manufacture of vacuum pump systems, NSH offers standardized pump systems which will match most applications �¢?? the VR pump systems. Typical areas of application for SINO-NSH VR pump systems are industry, research and chemistry. Here the focus is on processes for metal production and processing, drying and degassing, thermal treatment, coating in the area of semiconductor manufacture as well as surface refinement. VR pump systems are also used as backing pump sets for high vacuum systems in combination with diffusion pumps, turbo molecular pumps .
Sino-NSH-CP series is an oil purification system with thermal, filtering and centrifugal separation processing, with capacity from 1500 liter/hour to 6000 liter/hour. Sino-NSH-CP series is especially designed for the oil industry for the purification and recycling of liquid oil. This series is designed to overcome the harmful effects of oil contaminants, water and solid particles from fuel oil, lubricating oil and other mineral engine unit and land generator unit of power station so as to reduce wear of diesel engine and other machine, and prolong the serving life. The model is also used to separate two unsolvable liquids with different specific gravity or remove small amount of solid particle from liquid.
60000psi to 90000psi high pressure waterjet intensifier pump for waterjet cutting machine
Yinchuan Kester Electronic Technology Co., Ltd. has long served China's metallurgy, oil fields, cement, power plants, ships, and construction machinery industries. Di) MD MICRODETECTORSAECOITALWEBER ELETTRATEAFLEX, Balluff BALLUFF, Pepperl+Fuchs PEPPERL + FUCHS, BERNSTEIN Bernstein, DATALOGIC, Jade filter MP FILTRI, HARTING HARTING, Kerui CONTRINEX, LOVATO, Neumes PNEUMAX, Pizzato PIZZATO, SCHMERSAL SCHMERSAL, ILME, INTERNORMEN and other imported brands, stable foreign partners, quality and delivery can be guaranteed. The company has also set up a group of high-quality and experienced senior technicians and maintenance personnel, with skilled technology and many years of maintenance experience, can provide high-quality product pre-sales and after-sales service, technical support and quality tracking.
brands: rexroth, HAGGLUNDS, AVENTICS, Danfoss, Parker, MOOG, sunhydraforce, EOWARDS, Leybold, INFICON. Products: plunger pump, solenoid valve, gear pump, vane pump, direction valve, servo valve, proportional valve, hydraulic valve, hydraulic pump, etc
brands: rexroth, HAGGLUNDS, AVENTICS, Danfoss, Parker, MOOG, sunhydraforce, EOWARDS, Leybold, INFICON. Products: plunger pump, solenoid valve, gear pump, vane pump, direction valve, servo valve, proportional valve, hydraulic valve, hydraulic pump, etc
