Tobee 300TV-SP Vertical Slurry Pump is designed to be immersed in liquid for conveying abrasive, coarse particles, dirty water and particle contaminated water. Due to the design of the pump assembly, a shaft seal is not required and the pump can be operated in conditions that most pumps would have a low service life and their seal arrangement would not be effective.
40PV-SP Vertical Slurry Pump is ideal for a variety of submerged suction pumping applications. The vertical slurry pumps operate well in a variety of sump conditions, and can also be readily applied on floating dewatering or other floating pump platforms. As a true cantilevered vertical slurry pump, the SP Series does not have submerged bearings or seals, thus, eliminating the primary failure mechanism for similarly fielded pump lines. 40PV-SP Vertical pumps not only provide excellent wear life properties, they also operate efficiently to further reduce operating costs. These vertical slurry pumps can be fully elastomer lined or hard metal fitted. There are no submerged bearings or packing with a unique high capacity double suction design. Optional recessed impeller and suction agitator are available. Tobee 40PV-SP Vertical Slurry Pumps Performance Parameters: Size: 40mm Capacity: 19.44-43.2m3/h Head: 4.5-28.5m Max. power: 15kw Handing solids: 12mm Speed:1000-2000rpm Submerged length:900-2500mm Materials:High chrome alloy, Rubber, Polyurethane etc.
Tobee L Light Duty Slurry Pumps have been developed for continuous use in slurry applications where low to medium developed head is required, designed for lighter slurry densities up to 1,35. Shares proven unique design features with the AH slurry pump range, A key feature is the light duty high efficiency impeller, engineered with the latest hydraulic and wear technologies for high efficiency and increased wear life. With a range of high quality parts and different material combinations the L Light duty slurry pump has the versatility to ensure the most appropriate pumping solution provided for any given application. Design Features: Heavy duty construction with through-bolt design provides ease of maintenance and minimal downtime. Ductile iron fully lined casing provides durability, strength, safety, and long service life. Large diameter, slow turning, high efficiency impellers designed to achieve maximum wear life and low operating costs. Large, open internal passages designed to reduce internal velocities, maximize wear life and lower operating costs. Thick elastomer or alloy bolt-in liners provide superior corrosion resistance plus offer ease of liner change-out and interchangeability to reduce overall maintenance costs and maximize wear life. Designed for rugged duties while offering excellent efficiencies. Minimal shaft/impeller overhang reduces shaft deflection and increases packing life. Cartridge-style bearing assembly allows for maintenance in a clean environment without removal of the pump, resulting in reliable operation and prolonged bearing life. Grease or oil lubrication bearing assembly options offer ease of maintenance and reduced downtime. Full flush gland, low flow, and dry running centrifugal seals reduce flush water usage minimizing pump operating costs. Mechanical seals reduce flush water usage, minimizing pump operating costs.
Tobee E044 Split Packing Gland Assembly is used for 6x4 EAH slurry pump, 8x6 EAH slurry pump and 10x8 EM slurry pump. Slurry Pump Gland Assembly is primarily used to compress the packing to ensure a tight seal between the packing and the bushing. Gland Assembly has a split Gland Assembly that is typically used in slurry pumps. The stuffing box seal is composed of packing box body, packing, gland, bolt and other basic parts. The packing placed between the box body and the rotating shaft is radially extended under the axial force of the bolt force and the gland, so that the packing is tight. Adhered to the periphery of the rotating shaft, the lubricating oil added from the oil cup will form a very thin oil film between the packing and the contact surface of the rotating shaft when the shaft rotates, which not only has lubricating effect, but also prevents the medium in the kettle from escaping and Infiltration of gas outside the kettle. The gland is also available with a pair of open gland assembly used for slurry pumps. The slurry pump gland assembly is prone to damage due to stress during packing replacement and adjustment. Previously, usually with wire binding or replacement of gland assembly of slurry pump, often cause the media to continue to leak, both a waste of material, and unsafe. The packing gland has the characteristics of simple structure, easy to use, safe and reliable, and strong emergency. When the gland assembly is damaged, it can be easily and quickly replaced without affecting the normal use of the centrifugal slurry pumps.
Tobee 12/10 AH Slurry Pumps are the most comprehensive range of centrifugal slurry pumps for use in mining, minerals processing, coal preparation, dredging, metallurgy, power plant, chemical and general industry applications. The wetted parts materials designed by High abrasion and corrosion resistance alloy, rubber or polyurethane etc, Expecially for handling high abrasive, high density slurries.
Tobee M Medium Slurry Pumps are designed for continuous pumping of medium duty abrasive/dense slurries in processes from minerals processing, cyclone feed to regrind, flotation and tailings. 10x8E-M Medium Duty Slurry Pump is cantilevered, horizontal and centrifugal with double casing structure, It mainly suitable for pumping medium concentration slurries, 10x8E-M slurry pump applies in coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station etc.
EAM029A05 Slurry Pump Expeller Ring is an important Hi-seal wearing spares of 10/8 E-M Slurry Pump, Slurry Pump High Seal Parts mainly included: expeller, expeller ring, frame plate liner insert and stuffing box,there will be HS1 after the basic part numbers to represent Hi-seal pump parts, and compare with standard pump parts, the HS1 slurry pump parts are more suitable for sealing at high intake pressures as the large diameter slurry pump expeller. Slurry Pump Expeller Ring is used for AH/HH/L/M slurry pumps, The expeller ring is together work with expeller for the slurry pumps. They can not only help seal the pump, but also reduce the centrifugal force. The design and material of expeller is significant to its service life, Tobee offers expeller in cast iron, high chrome and rubber materials for options.
12x10E-M Centrifugal Slurry Rubber Impeller F10147R55 Wearing Spares Parts Supply. Tobee manufactures impellers with metal, rubber, and polyurethane materials etc, impeller for horizontal slurry pump, impeller for vertical slurry pump, impeller for gravel sand pump, and impeller for forth slurry pump etc. Tobee offers three different types of slurry pump impellers: open, closed, and semi-closed. Each has its own strengths and weaknesses, depending on the application. Some are better for solids handling, others are better for high efficiency. To learn more about the specifics of each type of slurry pump impeller. Tobee Rubber Slurry Pump Main parts: Bearing assembly - A large diameter shaft with short overhang minimizes deflection and contributes to long bearing life. Only four through bolts are required to hold the cartridge-type housing in the frame. Liners - Easily replaceable liners are bolted, not glued, to the casing for positive attachment and ease of maintenance. Hard metal liners are completely interchangeable with pressure-molded elastomers. Elastomer seal rings back all liner joints. Casing - Casing halves of cast or ductile iron with external reinforcing ribs provide high operating pressure capabilities and an extra measure of safety. Impeller - front and rear shrouds have pump out vanes that reduce recirculation and seal contamination. Hard metal and molded elastomer impellers are complete interchangeable. Cast in impeller threads require no inserts or nuts. High efficiency and high head designs are also available.
Sandman 20612-02-33 H20612-02-33 Shaft can be used for Mission Magnum 6x5x14 Pump and Mission 2500 Supreme 6x5x14 Pump. Mission I Pump Parts The Magnum is available in Magnachromeâ?¢, hard iron, stainless steel, and aluminum bronze fluid ends. 2500 Supreme Pump Parts The 2500 Supreme is available in hard iron, supreme hard iron, and aluminum bronze wearing spare parts. Sandmasater Pump Parts The Sandmaster centrifugal pumps contain almost all the features and designs of MAGNUM I for hydraulic motor drives. Magnum XP Pump Parts The Magnum XP pump parts are available in high chrome alloy or hard iron material options for different applications.
Sandman Crane Type Mechanical Seal 24036 (658416102) can be used for Mission Magnum XP series centrifugal pumps from 8x6x18, 12x10x23 and 14x12x22 XP Frac Pumps. Mission Magnum XP Blender Pump and MCM XL Pump are ideally suited for pumping high volumes of heavy slurries that are abrasive, corrosive, and difficult to pump. The compact overall dimensions make it an excellent choice for high volume mobile and stationary applications where a small footprint is critical. High chrome alloy or hard iron material options for different applications.
Tobee Mission Sandmaster Pumps have compact and adaptable that includes virtually all of the features of the MAGNUM I pumps. Mission centrifugal Sandmaster pumps to suit for all kinds of drilling sand pump application. Bare shaft pumps, matching motors are available from 7.5KW to 90KW, with rotation 800, 1000, 1150,1450, 1750 to 3500 RPM at 50Hz or 60Hz. The model 10x8x14 and 8x6x14 centrifugal sandmaster pump used on solid control system over 3000 meter-long drilling rigs, with big viscosity and heavy specific gravity drilling fluid. 8x6x11 centrifugal mud solid control feeding pump applies to under 3000 meter-long drilling rigs, and it also can be used to supply mud to triplex mud pump as a filling pump. 6 5 1 centrifugal pump applies to truck-mounted drilling rigs or pocket drilling rigs. 4x3x13 drilling centrifugal pump is usually used as measuring pump or replenishment pump. 3x2x13 model pump is usually used as clean water pump. Mission Sandmaster Pump Designs: Compact heavy-duty frame design for small space; Multiple application in the oil and gas industrial; Full open impeller reduces shaft loading; Replaceable stuffing box cover, Available in hard ductile iron, high chrome alloy fluid ends(casing, impeller, wear pad, stuffing box), customized fluid ends in stainless steel or aluminum bronze acceptable; Available in 8 different size, 3x2, 4x3, 5x4, 6x5, 8x6, 10x8; One-piece concentric and thicker casing with same power end; SKF bearings or equal; Oil or grease lube available; oil lube is for speeds in excess of 2400rpm; 3500rpm is available for 3x2x13 and 4x3x13 pump; Completely interchangeable with Mission Sandmaster and MCM Mud Master and all other popular brand design in the market; Spare parts are interchangeable with the standard model. The pumps can be unitized with hydraulic motors driven.
Tobee 100RV-SPR vertical slurry pumps and slurry pump spares to South Africa. The SP/SPR Vertical cantilever Sump pumps is a vertical spindle slurry pump. It is designed to transport corrosive, coarse particles, and highly concentrated slurry. It can operate normally without a shaft gland or shaft gland water, and the length of the shaft can be customized to the depth of the liquid level. The SP/SPR vertical slurry pump is a vertical type slurry pump. The inlet is oriented vertically and downward on one side of the vertical pump, and the outlet is oriented vertically and upward on the other side. It composed of the lower filter platform, pump body, impeller, shaft, guard plate, and bracket. The upper part of the SP/SPR pump is supported by bearings; the pump is installed under the liquid, and no shaft seal is used. It uses a belt drive (BD) and direct drive (CD) transmission type. The depth of the immersion liquid in the standard size range can be adjusted according to the needs of the user. Vertical Pumps Design features: 1. Vertical sump pumps are vertical, centrifugal slurry pumps submerged in sump to work. 2. They are designed for delivering abrasive, large particle and high density slurries. 3. These pumps have no need of any shaft seal and sealing water. 4. They can also be operated normally for insufficient suction duties. 5. Wet parts of type SP metal vertical slurry pump are made of abrasion-resistant metal. 6. All parts of type SP(R) rubber lined vertical slurry pump immersed in liquid are lined with rubber outer liner. They are suited 7. To transport non-edge angle abrasive slurry.
100RV-SPR Rubber Vertical Slurry Pump Parts including No.: SPR10206AR55, SPR10092R55, SPR10041R55, etc. Metal Model: 40PV-SP, 65QV-SP, 100RV-SP, 150SV-SP, 200SV-SP, 250TV-SP, 300TV-SP Submerged depth: E 900mm, G 1200mm, J 1500mm, L 1800m, M 2000m, Q 2400mm Wet End parts: Pump Impeller: SP40206A05, SP65206A05, SP10206A05, SP15206A05, SP20206A05, SP25206A05, SP30206A05 Pump Casing: SP40092A05, SP65092A05, SP10092A05, SP15092A05, SP20092A05, SP25092A05, SP30092A05 Pump Back Liner: SP40041A05, SP65041A05, SP10041A05, SP15041A05, SP20041A05, SP25041A05, SP30041A05 Rubber Model: 40PV-SPR, 65QV-SPR, 100RV-SPR, 150SV-SPR, 200SV-SPR, 250TV-SPR, 300TV-SPR Wet End parts: Pump Impeller: SPR40206, SPR65206,SPR10206, SPR15206, SPR20206, SPR25206, SPR30206 Pump Casing: SPR40092, SPR65092, SPR10092, SPR15092, SPR20092, SPR25092, SPR30092 Pump Back Liner: SPR40041, SPR65041, SPR10041, SPR15041, SPR20041, SPR25041, SPR30041 Impeller O-ring: RV064-S10, Discharge Pipe Gasket: SP10204, Rubber Back Liner Seal: E4124S01 RV004-1 100RV-SP Rubber Lined Vertical Slurry Pump is designed for handling abrasive and corrosive liquids and slurries, while submerged in sumps or pits. Suited for applications requiring greater reliability and durability than conventional vertical process pumps can offer. It is mainly used for pumping the slurries with high abrasive, strong corrosion and high concentration liquids contain suspended solid particles.
Tobee Wear Parts Impeller SPR10206 of 100mm SPR Vertical Sump Pumps are made of Ethylene Propylene Diene Monomer (EPDM) material which replace original 100RV-SPR Vertical Pump Parts on site. Tobee Vertical slurry pump named vertical spindle pump, Vertical sump pump, vertical cantilever pump. vertical submerged pump. Vertical sewage pump, Column pump as well. Impeller SP10206 - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary. Casing SP10092 - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR. Back Liner SP10041 - It forms a pump chamber with throat bush and volute liner where the slurry would flow through them, Tobee offers back liners are interchangeable with stardard pump back liners with high chrome, natural rubber, polyurethane for different working condition.
Tobee Vertical Slurry Pump Casing SPR10092 has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR. Tobee�® Vertical Slurry Pumps without submerged bearings or packings, Customized submerged length and suction agitator available. They are been called Spindle pump, sump pump, column pump, cantilever pump, submerged pump, and open-pit pumps as well. Tobee�® Identical Vertical Cantilever Pump Metal Model: 40PV-SP, 65QV-SP, 100RV-SP,150SV-SP, 200SV-SP, 250TV-SP, 300TV-SP Tobee Analogues Vertical Cantilever Pump Rubber Model: 40PV-SPR, 65QV-SPR, 100RV-SPR, 150SV-SPR, 200SV-SPR, 250TV-SPR, 300TV-SPR Tobee�® Replacement Vertical Metal Slurry Pump Wet End Parts: Vertical Sump Pump Impeller SP40206A05, SP65206A05, SP10206A05, SP15206A05, SP20206A05, SP25206A05, SP30206A05 Vertical Sump Pump Casing SP40092A05, SP65092A05, SP10092A05, SP15092A05, SP20092A05, SP25092A05, SP30092A05 Vertical Sump Pump Back liner SP40041A05, SP65041A05, SP10041A05, SP15041A05, SP20041A05, SP25041A05, SP30041A05 Tobee Alternative Vertical Rubber Slurry Pump Wet End Parts: Vertical Spindle Pump Impeller SPR40206, SPR65206, SPR10206, SPR15206, SPR20206, SPR25206, SPR30206 Vertical Spindle Pump Casing SPR40092, SPR65092, SPR10092, SPR15092, SPR20092, SPR25092, SPR30092 Vertical Spindle Pump Back liner SPR40041, SPR65041, SPR10041, SPR15041, SPR20041, SPR25041, SPR30041
Tobee 4x3C-AH Slurry Pump with ceramic shaft sleeve C075J04 that widely used as ash handling pump in as handling system in power plant. Slurry Pump Ceramic Shaft Sleeve, which has undergone destructive field tests for over 18 months, has proved to extend part life several times that of steel shaft sleeves on the same pump, same service. Total maintenance costs and down-time were reduced accordingly. Tobee's slurry pump ceramic shaft sleeves are precision formed of high density alumina, fired, and ground to size. The hardness of ceramics (9.0 to 9.5 MOH Scale) resists this destructive action, In addition, the ceramic coated sleeve surface is highly polished which, together with its lower co-efficient of friction, results in extended sleeve life and long service from the packing. One of the problems of concern to operators of centrifugal slurry pumps is the wear of shaft sleeves and the deterioration of packing material in the gland. This matter has also been under study by the Materials Research and Development Department of TOBEE PUMP for some time. The result is the development of a shaft sleeve of much superior wearing qualities. Tobee Slurry Pump Ceramic Shaft Sleeve, which has undergone destructive field tests for over 18 months, has proved to extend part life several times that of steel shaft sleeves on the same pump, same service. Total maintenance costs and down-time were reduced accordingly. Slurry Pump Steel Shaft Sleeve has always been the here-to-fore accepted material for shaft sleeves for most centrifugal slurry pumps. However, steel in shaft sleeves is subject to pitting, fritting and wear that often results in short part life. So Tobee Pump developments of a ceramic coating shaft sleeve of much superior wearing qualities.
3/2C-AH Slurry Pump is a heavy-duty slurry pump that designed to handle the most abrasive and dense slurries. The 3/2C-AH slurry pump offers users a wide range of seal and liner configurations, allowing the pump to be fully customized to meet any specific application requirements. 3/2C-AH slurry pumps offer unmatched power consumption, long component life, and unmatched reliability. Tobee�® 3/2 C AH Slurry Pumps Performance Parameters: Size: 3" x 2" Capacity: 39.6-86.4m3/h Head: 12-64m Speed: 1300-2700rpm NPSHr: 4-6m Eff.: 55% Power: Max.30kw Handling solids: 25mm Seal arrangement: Packing seal, Expeller seal, Mechanical seal
Tobee S Paper Pulp Pump is one kind of centrifugal single stage single suction paper pulp stock pump .it is widely used in such as paper making industry, pulp and paper, steel, chemical, food, sugar, or bioethanol industries .It can transport less than 6% concentration paper pulp, sewage water,chemicals or fine slurries etc.,and it can also transport the non-abrasion medium in other industries. Tobee�® S Series Paper Stock Pumps are widely used in papermaking, pulp mills, pulp medium of transportation, also applies to enterprise sugar, starchprocessing, chemical raw materials, such as the transmission medium. Available Interchangeable Andritz S Pumps Models and Spares:S80-265, S100-265, S125-265, S3 100-350.3, S125-350, S150-330, S3 125-400, S3 150-400.3, S3 200-380, S8 200-380, S3 150-470.3, S3 200-470.3, S3 250-430.3, S3 350-470.3, S8 350-470.6, S500-600, etc 100% Equivalent Andritz S pump spare parts including: Impeller (2 vanes, 3 vanes, 6 vanes, 8 vanes), Volute Casing, Casing Cover, Front Lining, Rear Lining, Stuffing Box Body, Shaft Wear Sleeve etc which for Andritz S series paper-pulp pumps.
20616-1 Stock no. 648408201S Bearing O.B for Magnum Centrifugal Pump 8x6x14, 6x5x14, 6x5x11, 5x4x14, 5x4x11, 4x3x13, 3x2x11. The Mission MAGNUM I has been engineered for the toughest jobs in drilling, production, well-servicing, and industrial applications. The revolutionary design of the MAGNUM I provides supreme-duty performance in all types of fluid pumping operations. Although it offers greater capacity and higher heads, the MAGNUM I remains the competitive pump of choice for aggressive applications. The MAGNUM I is more powerful, more durable, and easier to maintain than any conventional pump in use today. The Magnum has an open impeller design that contains wide-tipped vanes and a more tangential circumference of the suction allowing the pump to create a smoother flow pattern when handling abrasive fluids. The Magnum is available in Magnachrome, hard iron, stainless steel, and aluminum bronze fluid ends. The pumps can be unitized with electric motors, diesel engines, and hydraulic motors (horizontal, vertical, or close-coupled configuration). Also available, Horizontal and Vertical Close Coupled Magnum.
19123-01-30A Casing is an important Wear Parts for Mission Magnum 6x5x14 Centrifugal Pump. All of the pumps feature a concentric casing. This casing averages 37% thicker than conventional pump casings, and up to 50% thicker for the larger, mud pumping models. They are pressure rated at 1 .5 times the flange rating and are designed with a 1 /8â?³ erosion allowance. The concentric style casing has proven to offer the greatest pump life and reduced downtime. The walls of a concentric style casing are an equal distance from the impeller throughout the impeller circumference, which results in a smooth flow pattern. A volute style casing has a cutwater point that disturbs the fluid flow pattern creating an eddy. The concentric casing eliminates vibration, turbulence and aeration that is caused by the cutwater point in conventional volute pumps. It also reduces the high bearing loads and shaft deflection even at near shutoff flows. The Mission MAGNUM I has been engineered for the toughest jobs in drilling, production, well-servicing, and industrial applications. The revolutionary design of the MAGNUM I provides supreme-duty performance in all types of fluid pumping operations. Although it offers greater capacity and higher heads, the MAGNUM I remains the competitive pump of choice for aggressive applications. The MAGNUM I is more powerful, more durable, and easier to maintain than any conventional pump in use today.
