Fuel oil treatment general cleaners oil spill dispersant multipurpose cleaner oil industrial cleaner carbon remover electric cleaners motor cleaner oil filter cleaner scale remover scot remover rust remover rust preventive paint remover air conditioner cleaner hand cleaner eliminate odor cutting oil water treatment cooling water treatment boiler water treatment cooling water treatment test kit boiler water treatment test kit oil treatment corrosion inhibitor for gas scale inhibitor oxygen skavenger microbiocide demulsifier pour point depresant paraffin control fire extinguisher liquid foam 3% afff.
Water treatment chemical.
Chemical & waste water treatment, oil, equipment.Cleaning & overhaull
Water disinfectant clo2 clorine dioxide 100%. oxygen and nitrogen generators.
Water treatment chemicals.
Water treatment chemicals.
LC 122 is an effective wide band micro-biocide designed for use in algae and bacteria control. It does not cause foaming and is not lost by evaporation from the system. It is a concentrated blend of organo-sulfur compounds, which should be added only after proper dilution by slug feeding. Application: Use to control algae and bacteria in re-circulating commercial and industrial water cooling towers. Prior to its use, systems be cleaned to remove algae growth, microbiological slime and other deposits. Dosage: Initial slug additions of LC 122 per 1,000 gallons of water should be employed every 1 - 5 days or as needed. The frequency of addition depends upon the relative amount of bleed-off and the severity of the microbiological problem. Slug additions should be made in the sump of the cooling tower. During very hot weather, greater frequency or higher dosage may be required to increase its effectiveness. Handling & Precaution: It is a very strong alkaline treatment and may cause eye damage and skin irritation. Do not get in eyes, skin or on clothing. Wear goggles or face shield and rubber gloves when handling. Avoid contamination of food. Harmful or fatal if swallowed. In case of skin contact wash with plenty of soap and water. Remove contaminated clothing and wash before reuse. If product gets in the eyes, flush immediately with copious amount of clean cool water for at least 15 minutes. If swallowed, call physician. Do not induce vomiting or give anything by mouth to an unconscious person. Packaging: Available in pail of 20 lt.. Can also be custom packaged.
LC 123 is specially formulated for large installations high hardness water. It is developed for effective, economical cooling water treatment at hospitals, hotels, large apartment houses, office buildings and other industrial and institutional cooling installations with high hardness make-up water. It contains no phosphates, chromate, zinc, or other chemicals that cause pollution problem. Helps control mineral deposits, sludge and surface pitting and does not stain automobiles or buildings. Application Use a reliable automatic proportioner with timer for controlled dosage. Follow instructions for calculated bleed of rate and recommended daily maintenance treatment as suggested by the Field Chemist Personnel. The dosage and treatment program depend on size of installation and water hardness (ppm). Dosage Initial treatment : Add 1 gallon of LC 123 per 2,000 gallons of recirculating water. Maintenance treatment as per size of installation & hardness (consult our Technician) Handling & Precaution Wear protective clothing and eye protection should be provided and worn. In case of skin contact, immediately flush thoroughly with plenty of clean water. In case of eye contact, flush with copious of amounts of water for 15 minutes and obtain immediate medical attention. Refer to MSDS for more specific directions. Packaging Available in pail of 20 lt.. Can also be custom packaged.
LC 124 is an effective chlorine based designed for use in algae and bacteria control. It does not cause foaming. It is a concentrated blend of organo-chloro compounds which should be added only by slug feeding. Application: Use to control algae and bacteria in re-circulating commercial and industrial water cooling towers. Prior to its use, it is advisable that systems be cleaned to remove slime and other deposits. Dosage: An initial slug addition of 1 gallon of LC 124 per 2,000 gallons of water should be employed every 1-4 days or as needed. The frequency of addition depends upon the relative amount of bleed-off and the severity of the microbiological problem. Slug additions should be made in the sump of the cooling tower. During very hot weather, greater frequency or higher dosage may be required to increase its effectiveness. Handling & Precaution: It is a very strong treatment and may cause eye damage, mucous attack and skin irritation. Do not inhale, get in eyes, skin or on clothing. Wear goggles or face shield and rubber gloves when handling. Avoid contamination of food. Harmful or fatal if swallowed. In case of skin contact, wash with plenty of soap and water. Remove contaminated clothing and wash before reuse. If product gets in the eyes, flush immediately with copious amount of clean cool water for at least 15 minutes. If swallowed, call physician. Do not induce vomiting or give anything by mouth to an unconscious person. Packaging: Available in pail of 20 lt.. Can also becustom packaged.
LC 255 is a versatile and highly effective rust preventative for use on unpainted metals during outdoor storage or overseas shipping. LC 255 protects metal with heavy waxy film. It does not require any surface cleaning or preparation and covers the metal like a paint, but easily removable. LC 255 provides protection for storage of metal, equipment, tools, tanks, structures, machinery, castings, fittings, valves, doors, frames, fixtures, jigs, etc. Application: LC 255 can be applied by spraying, brushing or dipping. It is recommended to apply by dipping in a tank with water draining facilities which ensures maximum coverage, penetration and cost effectiveness. LC 255 absorbs water and moisture while lubricating plated surfaces and bare metals such as steel, iron, alumunium, copper, brass and lead. Handling & Precaution: Avoid contact with eyes and skin. In the case of contact with eyes, wash immediately with plenty of water. Seek medical advice. If ingested, do not induce vomiting, seek medical attention. Packaging: Available in pail of 20 lt.. Can also be custom packaged.
KB 224 is a special water based polymer with silicone specially designed to protect and keep a shine & wet look on vinyl, rubber, plastic and leather or other such surface materials. KB 224 protect surfaces from fading and cracking by reducing ultraviolet light, while bringing out color, restoring luster and shine, protects against abrasion. Eliminates static electricity to reduce dirt attraction. If less shine is desired, lightly buff with damp cloth. Application: Apply KB 224 with a clean cloth or sponge ( or spray ) with a cleaning action. Spread evenly, allow to penetrate and chemically bond for a few minutes then remove excess for a beautiful protective shine. On some surfaces a two coat application provides best results. Apply as needed to maintain shine and protective coating. Dosage: Use undiluted product. Handling & Precaution: This product may caused slipperiness on certain surfaces until it is completely dry. May caused smearing on glass or other transparent services. Avoid spills on eyes. Should avoid prolonged unnecessary contact with skin. May irritate when exposed for a longer period on certain sensitive skin. Harmful if swallowed. Keep away from children. Keep container capped in a cool dry place Packaging: Available in pail of 20 lt.. Can also be custom packaged.
KB 273 is concentrated degreaser specially formulated to penetrate, emulsify and disperse oil, grease, dirt, soot and burnt / residual carbon from a variety of hard surfaces. Specially designed for use in ovens, grills, chimneys, exitways, smoke escapes, air vents where thick deposit of soot/carbon is common by found. Most effective for oily residues and its water base composition make easy flushing. Application: Allow soaking time ( 5 – 30 minutes ) for effectiveness. Apply a thin layer by spraying or brushing, then leave for soaking. Brush and scrap gently to remove any hard soils if required then flush with water. ( Use KB 212 for best results ) Protective measures is suggested for cleaning personnel Dosage: Dilute with ratio of 1 : 10 ( max. ) with water depending on the dirt thickness. Use concentrated product or lower dilution for tougher stains. Dilute up-to 50 times for regular cleaning work. Repeat if necessary Handling & Precaution: Avoid eye contact. Should avoid prolonged contact with skin. Harmful if swallowed. Use protective gloves where contact is in evitable Packaging: Available in pail of 20 lt.. Can also be custom packaged.
LC 101 is used in steam boiler systems where water is zeolite softened or in natural waters very low in hardness. This treatment will prevent scale formation from residual hardness in addition to conditioning sludge. LC 101 is a balanced blend of polymers which are mildly alkaline scale and corrosion inhibitors in addition to sodium sulfite for added pitting and corrosion protection. If 20 to 30 ppm (mg/l) of sulfite cannot be maintained with a normal dosage of LC 101, add LC 102 to hold this recommended level. Application: Easily fed to the boiler as a slug dosage or by chemical proportioning pump directly in to the boiler. It can also be injected into the feedwater tank. Formula LC 101 contains no heavy metals. Dosage: Initial dosage is one (1) quart per 1,000 gallons and one (1) quart thereafter for every 800 gallons of make-up water. Maintain 20-30 ppm (mg/l) of orthophosphate in the boiler water. Handling & Precaution: Wear protective clothing and eye protection should be provided and worn. In case of skin contact, immediately flush thoroughly with plenty of clean water. In case of eye contact, flush with copious of amounts of water for 15 minutes and obtain immediate medical attention. Packaging: Available in pail of 20 lt.. Can also be custom packaged.
LC 232 is a very strong concentrated descaler, specifically designed to remove silica based scales and other stubborn scales. It is a special blend of volatile acids, corrosion inhibitors & dispersing agents. It effectively removes stubborn silica scale and soil of silicate/phosphate nature from metal and other surfaces. LC 232 is an excellent additive for the LC 231 & LC 233 for additional effectiveness against silica based scales and effectively bring down cost by reducing the amount of other descalers. Its special formulation dissolves scale and rust deep down with the selective inhibitors protecting metal surfaces. Application Spray or brush on surfaces. Clean surface free from rust, soil and dirt. Apply LC 232. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat and then flush off with water. Flush with water until all scale is removed. Add with other descaler like LC 231 & LC 233 for stubborn and difficult to remove scales. For best results use circulation or dipping method use of passivating agent like LC 252 or LC 253 is essential. Make test strip before use. NOT TO BE USED ON GLASS/SILICATE BASED SURFACES. Dosage Dilute one part of LC 232 with up to 10 parts of water or depending on the thickness of scales. Handling & Precaution Irritating to eyes and skin. Protective clothing and eye protection should be provided and worn. After contact with skin, wash immediately with plenty of water. In case of eye contact irrigate thoroughly with water for at least 15 minutes. Seek medical advice. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 202 is a water based general purpose cleaner to Penetrate, emulsify and disperse oil, grease, dirt and grime And other types of soils from a variety of hard surfaces. Ideal for cleaning walls, floors, desks, light fixtures, Automobiles, painted woodwork. Also can be used on metal Surfaces such as stainless steel, aluminum, cooper and Brass. Application Spray, mop, brush wipe, dip method are recommended. Use for cleaning Walls, floors, desks, light fixtures, automobile, painted wood work. Dosage Dilute with ratio of 1 : 15 (min) up to 1 : 200 with water depending on the dirt Thickness & type of the surfaces Handling & precaution Avoid spills on eyes. Should avoid unnecessary contact with skin. Can Irritate when exposed for a longer period. Harmful if swallowed. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 219 is a technical specialty cleaner designed to remove difficult deposits & residue on glass surfaces arrising from long exposure to external weather Conditions. The stains & marks, including dried fungus generally builds up on Exposed glass surfaces can easily be removed using lifechem’s lc 219. It Is a technical product & requires complete attention to the “guidelines on Application” during it’s use. Lc 219 effectively removes the stains & deposits Which is generally not removed by standard glass cleaners. It leaves glass Sparkling clean, smear-free. The anti static components repel tiny dust particles and thus reduces Deposits efficiently. Use lifechem’s lc 203 ; glass cleaner regularly to keep Your glass surface in a sprkling condition. Application 1. Use undiluted or diluted product as required depending on the stains & Deposits. A small test patch must be made to select dilution. 2. Damp a piece of clean white wiping cloth with lc 219 and squeeze out any Extra liquid to avoid spreading & flowing during wiping. 3. Spread a this layer using the damp/wet cloth on the stained glass or mirror Surface. Select only a small area depending on drying rate. 4. Wipe-off using a separate piece of clean, white cloth to a shining lusture. A Soaking time may be required in some cases. 5. Use lc 203 to rinse the cleaned surface using glass-wiper in the usual Method. 6. Leave it to dry. 7. Repeat if necessary for highly soiled stains, deposits etc. 8. Never be used on coated glass unless proved to be safe after testing. Dosage May be used undiluted or may be diluted to suit method of application and extent Of contamination. Suggested dilution is 2:1 or 1:1. Use clean & softened Water only. Un attended application may result into damage. Handling & precaution Avoid spill & stains of lc 219 on ceramic tiles, glass as prolonged exposure to Lc 219 direct effect. Keep away from children. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 250 is a water displacing anti corrosion compound Used to prevent rust on metal surfaces with unlimited Applications in the fields of marine, automobile, aviation Farming, etc. Lc 250 creeps along surfaces and into cracks to Lubricate, loosen frozen parts and displace water. The Loosened rust can easily be removed. The displacing Mechanism works by preferential wetting. The attraction, Of the preventative that of water, thus displacing water. Application Apply lc 250 to metal surfaces either by brushing or dipping. When dipping is used, allow excess chemical to drip prior to Storage. Handling & precaution Avoid unnecessary skin contact. Prolonged contact may cause Irritation. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 270 is a water based general purpose cleaner to Penetrate, emulsify and disperse oil, grease, dirt and Grime and other types of soils from a variety of hard Surfaces. Ideal for cleaning walls, floors, desks, light Fixtures, automobiles, painted woodwork. Also can be Used on metal surfaces such as stainless steel, Aluminum, cooper and brass. Application Spray, mop, brush wipe, dip method are recommended. Use for Cleaning walls, floors, desks, light fixtures, automobile, painted Wood work. Dosage Dilute with ratio of 1 : 10 with water depending on the dirt Thickness Handling & precaution Avoid spills on eyes. Should avoid unnecessary contact with Skin. Can irritate when exposed for a longer period. Harmful if Swallowed. Packaging Available in pail of 20 lt. Can also be custom packaged.
Lc 300 is a designed specifically for stains on granite Surfaces arising out of contamination during production Or due to storage. It is very effective for stains on granite Surfaces due to poor quality water, inproper storage & Soil contamination. It is an acid based special blend of Selected penetrants, emulsifiers, dispersant & solvent Carriers designed to effectively penetrate, react, dissolve & remove the stains from the surfaces as well as deeper Into the granite structure without affecting the surface. Application Make sure that the granite surfaces are free from dust, soil & dirt. Apply lc 300 on The pre-treated surface by brushing to leave a thin uniform film on the whole Surface. Do not leave any surface untreated. Wait until 15-30 minutes or more until The stains start dispersing. Rinse and wipe clean the whole surface with demin Water. For deeper & thicker stains, repeat the process. May not be suitable for Certain types of granite & marble. Always make a test sample before final Application. Handling & precaution Avoid contact with eyes, skin and clothing. In case of contact, immediately wash With plenty of water. Harmful if swallowed. Packaging Available in pail of 20 lt.. Can also be custom packaged .
Multi type glass cleaner
