Due to its special thermal treatment, tempered glass boasts higher impact strength and freeze-thaw resistance compared to regular glass. All tempered glasses are subject to mandatory edge pre-treatment. If broken, such glass falls apart to small fragments with uncut edges. The glass tempering has the following effects:: impact strength rises 5-10 fold flexing strength rises 2-3 fold operating temperature range increases to -150 to +300°C The tempered glass has quite a broad range of applications: glass panes, multilayer glasses with different properties, all-glass partitions, staircases, stairs, hand rails, car windows etc. The tempered glass can withstand hard blows perpendicular to its plane. Despite its improved properties, however, tempered glass is still a fragile material. It is especially susceptible to end loads, so such glass should be installed with extreme care.
Carbon fiber modification on engine hood,empennage, surrounding surface, car handle, rotary plate, ect,. is the desire of car fans. Car fans are bothered by this problem any more after the carbon fiber vinyl come out as its price is lower and easy to operate Model : K9291, K9292, K9293, K9296, K9297 Material Size : 127cm × 50M Fabric : 0.09mm Glue : 30µ paper : 140g.
Chopped Strand Mat Fiberglass Chopped Strand Mats are non-woven fabrics consisting of randomly distributed chopped strands held together with a powder or emulsion binder. Chopped Strand Mat is compatible with unsaturated polyester, vinyl ester, epoxy and phenolic resins. The products are most widely used in hand lay-up process and can also be used in filament winding, Compression molding and continuous laminating processes. The typical end-use applications include various panels, boats, FRP roof shoot, Autonitive parts, bathroom equipment and cooling towers. Product Features 1.Uniform density ensures consistent fiberglass content and mechanical properties of the composites products. 2.Uniform powder distribution ensures good mat integrity, little loose fibers and small roll diameter. 3.Excellent flexibility ensures good moldability with no spring-back at sharp corners. 4.Fast and consistent wet-out speed resins and rapid air release reduce resin consumption, improving manufacturing costs, productivity and mechanical properties of the end products. 5.The composite products have high dry and wet tensile strength and good transparency. General Data Binding type : Powder or Emulsion; Densily : 85-900g/m2; Width : Max.3300mm, Tapes available. Edge : 1 or 2 untrimmed edge available upon request.
Surfacing Tissue Surfacing Tissue mainly used in the surface layers of FRP products. It features even Fiber distribution, soft feel, level and smooth fiber surface, less glue content, quick resin soak and good pattern fitness. It can improve the product surface property on corrosion resistance, compressive strength, seepage resistance, and longer service life. It is also suitable for spraying; pattern pressing and other FRP pattern technology. Packaging Product is manufacture in form of a roll wrap on a paper tube then after packed in a plastic bag and placed with in a cardboard carton. Rolls can be loaded in a container directly or on pallets. Stroge Should be stored in dry, cool, clean and rain-proof area. Recommended temperature range of storage is between 10~30 and relative humidity between 50%~75%.
3-D spacer fabric construction is a newly developed concept . The fabric surfaces are strongly connected to each other bv the vertical pile fibers which are interwoven with the skins . Therefore, lhe 3-D spacer fabric can provide good skin-core debonding resistance, excellent durability and superior integrity. In addition, the interstitial space of the construction can be filled up wilh foams to provide synergistic support with vertical piles. These products have broad application prospects in automobile, Iocomotive, aerospace, marine, windmills, building and other industries. Product Characteristics The 3-D spacer fabric consists of two bi-directional woven fabric surfaces, which are mechanically connected with vertical woven piles. And two S-shaped piles combine to form a pillar, 8-shaped in the warp direction and 1-shaped in the weft direction. The 3-D spacer fabric can be made of glass fiber, carbon fiber or basalt fiber. Also their hybrid fabrics can be produced. The range of the pillar height:3-50 mm, the range of the width:3000 mm. The designs of structure parameters including the areal density, the height and distribution density of the pillars are flexible. The 3-D spacer fabric composites can provide high skin-core debonding resistance and impact resistance and impact resistance, light weight. high stiffness, excellent thermal insulation, acoustic damping, and so on.
Ceramic Tiles are available in Various designs, quality ans sizes Few of Qualities available with are are Digital Wall Tiles,Digital Vitrified Tiles,Double Charged Vitrified Tiles Polished Vitrified Tiles,Digital Sugar Finish Tiles,Ordinary Tiles (Economic) Tiles are available in following Sizes 1200x600, 1200x800, 800x800, 600x600, 605x605, 400x400, 300x300, 300x450, 375x250, 300x300, 300x200, 250x250
Product Code Product Description PRS-ASVP00127 Vakuum Pyknometer STANDARDS : EN 12697-5,EN 13108,ASTM D2041,AASTHO T209,T283 Transparent plexiglass made, complete with valve and gauge. it is used for a rapid determination of asphalt content, bulk specific gravity of aggregates. The max. theoretic specific gravity of bituminous uncompacted road mixtures and the percent air voids in compacted mixtures. Dimensions dia. 300x450 mm Weight 10 Kg
Product Code Product Description PRS-ASFP00129 Asphalt Flash Point Apparatus STANDARDS : BS 4689, ASTM D92, AASHTO T48, UNI4160, IP 36/67, UNE 7075, EN 22592, NFT60-118, CNR N0 72 It is used to determine the â??open-cupâ?�, flash and fire points of oil products with a flash point above 80Â°C. Calibrated cup. Gas or liquid gas lighting device above the cup. 550 W electric thermostatic heater. Power supply 220-240 V 1ph 50 Hz 550 W Dimensions 220 x 220 x 450 (h) mm. Weight 11 Kg
Product Code Product Description PRS-ASKW00126 Kinematic Viscosity Apparatus STANDARDS : ASTM 2170,AASHTO T201,EN 12595 The temperature, from room temperature to 135Â°C, remains constant within Â± 0.1Â°C. Electric stirrer, electric heater and cooling (COIL) system. Digital read-out and regulation of temperature. Safety device for temperature and water level with alarms. 19 litre bath in pyrex glass with external protection in plexiglass. Support base with housing seats. Capacity: Five viscometers to be ordered separately according to viscosity. Dimensions 300 x 300 x 500 (h) mm. Power supply 220 V, 50 Hz, single phase, 1700 Watts Weight 12 kg.
Product Code Product Description PRS-CM0090 Jolting Table, EN, 220-240 V 50 Hz, (60 Hz version is available upon request) PRS-CM0091 Jolting Table with Soundproof Safety Cabinet, EN, 220-240 V 50 Hz PRS-CM0092 Three Gang Mould for 40x40x160 mm PRS-CM0093 Feed Hopper 40x40x160 mm for PRS-CM0092 PRS-CM0094 Short and Long Spreaders and Straightedge, for PRS-CM0092 STANDARDS : EN 196-1; ISO 679 Jolting Table is used for compacting of cement specimens in 40x40x160 mm mould and consists of mould table seated on a rotating cam driven at 60 r.p.m. The falling height is 15 mm conforming to EN 196-1. The machine is equipped with a counter which provides automatic shut off at end of preset drop numbers. Weight and dimensions of the jolting table fully comply with the requirements of EN 196-1 standard. When used with PRS-CM0092 Three Gang Mould and PRS-CM0093 Feed Hopper, the total weight of the moving part is 20 kg Â± 0.5 kg. Without PRS-CM0092 and PRS-CM0093 the weight of the moving parts is 6.85 kg. Rapid mould lock and release system allows easy and quick operation. The supporting frame of the machine has been designed to ensure precise dimensions, table flatness, correct centering of the three gang mould on the table. The motor and gearbox assembly is enclosed in a protective housing, which promotes user safety (the moving parts are inaccessible) and long life for the gearbox. The standard model can be supplied with a safety/noise reduction cabinet. The cabinet is lined internally with soundproofing material to reduce sound level conforming to CE directives. PRS-CM0093 Feed Hopper is used for filling PRS-CM0092 Three Gang Moulds placed on the Jolting Table. PRS-CM0092 Three Gang Mould, PRS-CM0093 Feed Hopper, PRS-CM0094 Short and Long Spreaders and Straightedge should be ordered separately. Product Code PRS-CM0090 PRS-CM0091 Dimensions 1050x350x500 mm 1440Ã?500Ã?575 mm Weight (approx.) 55 kg 125 kg Motor Speed 60 r.p.m Drop Height 15 mm Power 250 W
Air Entrainment Meter for Mortar Product Code Product Description PRS-CM0066 Air Entrainment Meter for Mortar 1 lt. STANDARDS : EN 413-2, 459-2, 1015-7 The PRS-CM0066 Air Entrainment Meter for Mortar is used for determining the air content of cement paste, cement mortar and lime mortar. The air entrainment meter is manufactured from cast aluminum, the upper part and the lower test pot are held together with an air-tight seal which are easily adjusted by using the two spring clamps. The pressure gauge is installed in the head of the meter and the scale works in the 0-20 volumetric % range. The air is compressed with a hand pump installed in the system and the smart configuration of the test and correction buttons enables fast and simple testing. Dimensions 200x200x320 mm Weight (approx.) 3,5 kg
Product Code Product Description PRS-KA0800 Slake Durability Apparatus, 220-240 V 50 Hz PRS-KA0802 Pair of Mesh Drums for PRS-KA0800 STANDARDS : ASTM D4644 This test method has been developed to assess the deterioration of rocks over a period of time when subjected to water immersion. Slake durability is a simulated weathering test to determine abrasion resistance during wetting and drying cycles of shale and similar soft rocks as used in embankments and other construction-related applications. Samples are alternately tumbled in mesh drums through a water medium and oven-dried for two cycles. The percent loss of mass is referred to as the slake durability index. The PRS-KA0800 Slake Durability Apparatus consists of a motorized drive unit which is mounted on a baseplate and which can rotate two or four drums at a speed of 20 r.p.m. The tank assemblies are filled with water to a level 20 mm below the drum axis. The test drums are manufactured from 2.00 mm mesh, 140 mm dia. x 100 mm long. Dimensions 1300x150x450 mm Weigth (approx.) 15 kg
Product Code Product Description PRSD-1295 Laboratory Oven 50 lt., 220-240 V 50-60 Hz PRSD -1300 Laboratory Oven 120 lt., 220-240 V 50-60 Hz PRSD -1305 Laboratory Oven 250 lt., 220-240 V 50-60 Hz PRSD -1310 Laboratory Oven 500 lt., 380 V 50 Hz PRSD -1315 Laboratory Oven 700 lt., 380 V 50 Hz STANDARDS: EN 932-5, 1097-5; ASTM C127, C136, D558, D559, D560, D698, D1557, D1559 BS 1377:1, 1924:11; UNE 103300 PARSROS * PRSD Series Laboratory Ovens have been designed for drying asphalt, soil, rock, concrete, aggregate or similar materials. 50, 120, 250, 500 and 750 liter capacity models are available. Temperature range is from ambient to 200Â°C. The interior is manufactured from stainless steel and the exterior is robustly constructed from sheet steel finished in powder coated paint. All models are fan circulated (forced convection), fitted with direct reading digital control unit and equipped with an analogue overtemperature protection thermostat. Laboratory Ovens are supplied complete with 2, 3, 4 or 5 shelves according to the capacity. Product Code Internal Dimension External Dimension Weight (approx.) PRSD-1295 410x350x360 mm 580x600x570 mm 20 kg PRSD -1300 610x500x400 mm 770x750x650 mm 56 kg PRSD -1305 800x600x570 mm 970x840x790 mm 85 kg PRSD -1310 1100x790x580 mm 1401x920x770 mm 130 kg PRSD -1315 1400x890x570 mm 1600x1130x770 mm 170 k
PRSG-0413 Sieve Shaker with Frequency and Time Adjustment, for 200/300/400mm Dia. Frame Sieves. 220-240 V 50-60 Hz PRSG-0413/110 Sieve Shaker with Frequency and Time Adjustment, for 200/300/400mm (8â?/12â?/16â?) Dia. Frame Sieves, 110 V 60 Hz STANDARDS : EN 932-5; ISO 565, 3310-1, 3310-2; ASTM E11, 323; BS 410-1, 410-2 The PRSG-0413 Sieve Shaker is fitted with a very efficient clamping device that ensures sieves are held firmly without over-tightening and allows them to be quickly removed and replaced. The shaker is fitted with a timer which can be preset to any duration up to 60 minutes. The PRSG-0413 sieve shaker has been specially designed to operate with heavy samples without loss of performance. It is equipped with a dynamic power source which ensures the right vibration is imparted to the sieves and sample for fast, accurate and reproducible tests. The vertical movement is fixed to ensure the sample spends maximum time on the sieve surface. The unique vibratory action also helps keep the apertures clear and free from binding. Technical Specifications Sieve Capacity 15 pieces of 200 mm (8â?) sieves + pan and cover 10 pieces of 300 mm mm (12â?) sieves + pan and cover 7 pieces of 400 mm (16â?) sieves + pan and cover Dimensions 650x650x400 mm Weight (approx.) 147 kg Power 370 W
PRSG-0411 Sieve Shaker with Time Adjustment for 200/300 mm(8â?�/12â?�) Dia. Frame Sieves, 220-240 V 50-60 Hz PRSG-0411/110 Sieve Shaker with Time Adjustment for 200/300 mm (8â?�/12â?�) Dia. Frame Sieves, 110 V 60 Hz PRSG-0412 Sieve Shaker with Frequency and Time Adjustment, for 200/300mm (8â?�/12â?�) Dia. Frame Sieves, 220-240 V 50-60 Hz PRSG-0412/110 Sieve Shaker with Frequency and Time Adjustment,for 200/300mm (8â?�/12â?�) Dia. Frame Sieves, 110 V 60 Hz STANDARDS : EN 932-5; ISO 565, 3310-1, 3310-2; ASTM E11, 323; BS 410-1, 410-2 The PRSG-0411 and PRSG-0412 Sieve Shakers impart a circular motion to the material being sieved so that it makes a slow progression over the surface of the sieve. They are equipped with a dynamic power source which ensures the right vibration is imparted to the sieves and sample for fast, accurate and reproducible tests. The vertical movement is fixed to ensure the sample spends maximum time on the sieve surface. The unique vibratory action also helps keep the apertures clear and free from binding. The PARSROS Sieve Shakers are fitted with a very efficient clamping device that ensures sieves are held firmly without over-tightening and allows them to be quickly removed and replaced. The timer can be preset for any duration up to 60 minutes. The PRSG-0412 model has the additional frequency adjustment property. Technical Specifications Sieve Capacity 15 pieces of 200 (8â?�) mm sieves + pan and cover 10 pieces of 300 mm (12â?�) sieves + pan and cover Dimensions 510x510x370 mm (for both models) Weight (approx.) 86 kg (for both models) Power 250 W (for both models)
Product Code : Product Description PRSG-0420 High Capacity Screen Shaker Time-Controlled, 220-240 V 50-60 Hz PRSG-0420/110 High Capacity Screen Shaker Time-Controlled, 110 V 60 Hz PRSG-0422 High Capacity Screen Shaker Frequency & Time-Controlled, 220-240 V 50-60 Hz PRSG-0422/110 High Capacity Screen Shaker, Frequency and Time-Controlled, 110 V 60 Hz PRSG-0425 Pan PRSG-0426 Soundproof Safety Cabinet STANDARDS : EN 1339, 1367-1; TS 2824 The PRSG-0420 and PRSG-0422 are ideal for sizing large quantities of crushed stones, sand, gravel, slag, coal, coke, ores, pellets and similar materials. The screen shaker has a capacity of approx. 30 kg of sample. To be use with 667x452x67 mm dimension screens. The shaker has 6 screens and 1 pan capacity. PRSG-0420 model is time-controlled, PRSG-0422 model is frequency and time-controlled. Various sized wowen wired from 100 mm (4â?�) to 4 mm (no.5) or perforated plate from125mm to 5.6mm screen trays are available on request. PRSG-0426 Soundproof Safety Cabinet is manufactured from sheet steel lined internally with soundproofing material to reduce noise and for protection from dust. Screen trays and Soundproof Safety Cabinet (PRSG-0426) should be ordered separately. The PRSG-0420 or PRSG-0422 is supplied complete with; â?¢ Pan (PRSG-0425) Woven Wire Cloth Screen Trays ASTM E11 Perforated Plate Screen Trays Product Code Aperture mm (in) Product Code Aperture mm (in) PRSG-8WC1000 100 mm (4 in) PRSG -8PC0056 5.6 PRSG-8WC0900 90 mm (3 Â½ in) PRSG -8PC0080 8 PRSG-8WC0750 75 mm (3 in) PRSG -8PC0112 11.2 PRSG-8WC0630 50 mm (2 in) PRSG -8PC0160 16 PRSG-8WC0500 45 mm (1 Â¾ in) PRSG -8PC0224 22.4 PRSG-8WC0450 37.5 mm (1 Â½ in) PRSG -8PC0315 31.5 PRSG-8WC0375 31.5 mm (1 Â¼ in) PRSG -8PC0450 45 PRSG -8WC0315 25 mm (1 in) PRSG -8PC0630 63 PRSG -8WC0250 22.4 mm (7/8 in) PRSG -8PC1250 90 PRSG -8WC0190 19 mm (Â¾ in) 125 PRSG -8WC0160 16 mm (5/8 in) PRSG -8WC0125 12.5 mm (Â½ in) PRSG -8WC0112 11.2 mm (7/16 in) PRSG -8WC0095 9.5 mm (3/8 in) PRSG -8WC0080 8 mm (5/16 in) PRSG -8WC0063 6.3 mm (Â¼ in) PRSG -8WC0056 5.6 mm (No. 3 Â½ in) PRSG -8WC0047 4.75 mm (No. 4 in) PRSG -8WC0040 4 mm (No. 5 in) SCREEN SHAKER Dimension 587x787x850 mm Weight (approx.) 170 kg Power 550 W SCREEN TRAYS Dimensions 667x452x67 mm Weight (approx.) 7 kg
Testing Sieves STANDARDS : EN 933-2; ISO 565, 3310-1, 3310-2; ASTM E11, 323 PARSROS offers a wide range of High Quality Testing Sieves which are used in all types of sieve testing applications, from sampling and classification of soils, aggregates and other powdered and granular materials. PARSROS testing sieves are of the highest quality to ensure consistent fit, accurate specifications and durable construction. Woven Wire Cloth and Perforated Plate Sieves are supplied in 200 mm and 300 mm frame diameters in various nominal aperture sizes suitable for several applications and standards. Wet Washing Sieves are used for wet testing of various materials enabling to wash the fines through the sieve without losing any of the sample. Available in 200 mm diameter with 100 mm and 200 mm deep models. All parts of testing sieves are manufactured from stainless steel. Receiving Pans and Lids are available in stainless steel with 200 mm and 300 mm diameters.
Product Code Product Description PRSD-1450 Muffle Furnace 3 lt. 1000Â°C, 220-240 V 50-60 Hz PRSD-1455 Muffle Furnace 6 lt. 1100Â°C, 220-240 V 50-60 Hz PRSD-1460 Muffle Furnace 5 lt. 1200Â°C, 220-240 V 50-60 Hz PRSD-1462 Muffle Furnace 5 lt. 1200Â°C Programmable Timer, 220-240 V 50-60 Hz PRSD-1465 Muffle Furnace 5 lt. 1600Â°C, 380 V 50 Hz The PRSD Series Muffle Furnaces are widely used for determining various properties of construction materials, and they cover a temperature range from 1100Â°C to 1600Â°C, they are all front loading for easy operation and are of a double skin construction to maintain a cool outer case. Up to 1300Â°C, open wire based models are also produced. Excellent temperature control is provided by a PID digital control system. A vertical counter balanced door keeps the hot insulation away from the operator which opens in an upward movement. The Furnace has a safety switch which isolates the power when the door is opened.
Product Code Product Description PRS-ZE1500 Pinhole Test Apparatus PRS-ZE1502 PVC Tubing Ã? 10x8 mm 10 m Coil STANDARDS : BS 1377:5; ASTM D4647 Water flowing through fine-grained soils with high sodium content makes them highly erodible. The PRS-ZE1500 Pinhole Test Apparatus is used for evaluating the erodibility of clay soils by flowing water through a small hole that is drilled through the compacted specimen. The apparatus consists of a cylindrical metal container fitted one end with a water inlet and the other end with an outlet connection, a standpipe tube with scale and a stand to support the apparatus. Dimensions 150x200x1200 mm Weight (approx.) 3.5 kg
Product Code Product Description PRS-ZE0160 Soil Lathe / Trimmer and Extruder PRS-ZE0162 Open Wire Saw PRS-ZE0164 Wire Saw PRS-ZE0166 Trimming Knife PRSGG-2205 Porcelain Mortar with Pestle 130 mm dia PRSGG-2215 Rubber Headed Pestle The PRS-ZE0160 Soil Lathe, Trimmer and Extruder is used to extrude and trim soil samples from 35 mm to 100 mm diameter to reduce samples. It should be used together with PRS-ZE0162 Open Wire Saw. Open Wire Saw, Wire Saw, Trimming Knife, Porcelain Mortar with Pestle. The Rubber Headed Pestle can be ordered separately. Technical Specifications Specimen Lathe 35x70 mm to 100x200 mm SpecimenTrimming and Extrusion 35x70 mm to 50x100 mm Vertical Daylight 260 mm Dimensions 220x300x450 mm Weight (approx.) 15 kg