Lap Joint flanges are used on piping fitted with lapped pipe or with lap joint stub ends. The lap joint flange with the stub end assembly are normally used in systems requiring frequent dismantling for inspection and cleaning and where the ability to swivel flanges and to align bolt holes materially eases the erection of large diameter or unusually stiff piping. These flanges are also used in applications where there is a need to facilitate bolt alignment. These type of flanges are similar to slip-on flanges. The only difference is that it has a curved radius at the bore and face to accommodate a lap joint stub end. They may be used at all pressures and are available in a full size range. These lap joint flanges slip over the pipe, and are not welded. They are otherwise fastened to it. Here the bolting pressure is transferred to the gasket by the pressure of the flange against the back of the pipe lap. DIMENSION SPECIFICATIONS AS PER THE INTERNATIONAL STANDARD ASTM, ASME, API, AISI, BS, ANSI, DIN, JIS, MSSP, NACE SIZE : ½" to 48" (As Per Customer Requirement) CLASS : 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS DIN Standard ND-6, 10, 16, 25, 40 Etc MATERIAL GRADE: Carbon Steel Lap Joint Flange : ASTM A105, ASTM A 694 F42 Low Temperature Carbon Steel Lap Joint Flange : A350 LF2/A350 LF3 Copper Alloys Lap Joint Flange : ASTM / ASME SB 61 / 62 / 151 / 152 C 70600 (CU -NI- 90/10 C 71500 (CU -NI- 70/30) UNS NO. C 92200, UNS NO. C 83600,UNS NO C 10100 C 10200, C 10300, C 10800, C 12000, C 12200 Nickel Alloys Lap Joint Flange : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy C22, C276 Duplex Lap Joint Flange : ASTM A 182 UNS F 44, F 45, F51, F 53, F 55, F 60,F 61 Stainless Steel Lap Joint Flange : ASTM 182 F 304, 304L, 304H, 309S, 309H, 310S, 310H, 316, 316TI, 316H, 316L, 316LN, 317, 317L, 321, 321H, 347, 347H, 904L Alloy Steel Lap Joint Flange : ASTM SA 182 F1/F5/F9/F11/F22/F91 ADVANTAGE OF LAP JOINT FLANGES: Lap Joint flanges have certain special advantages over other flanges. These are as follows: Lap Joint flanges have the freedom to swivel around the pipe. This facilitates the lining up of opposing flange bolt holes. Lack of contact with the fluid inside the pipe leads to the greater durability of these flanges. In piping systems which corrode or erode quickly, the lap joint flanges may be salvaged for re-use. The pressure-holding capacity of lap joint flanges is little. But it is better than that of slip-on flanges. The Lap Joint works as a backing ring on the stub. The main advantage of lap joint flange is that the bolt holes can be aligned with the matching flange after the welds have been completed. They allow rotational alignment capability. VALUE ADDED SERVICES : Hot Dip Galvanizing Electro Polish Test Certificate As Per EN 10204 - 3.1 & 3.2
This is similar to the slip-on Flange in outline, but the bore is threaded, thus enabling assembly without welding. This obviously limits its application to relatively low pressure piping systems. The Flange may be welded around the joint after assembly, but this is not considered a satisfactory method of increasing its use in pressure applications. DIMENSION SPECIFICATIONS AS PER THE INTERNATIONAL STANDARD ASTM, ASME, API, AISI, BS, ANSI, DIN, JIS, MSSP, NACE SIZE : 1/8" to 48" (As Per Customer Requirement) CLASS : 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS DIN Standard ND-6, 10, 16, 25, 40 Etc MATERIAL GRADE : Stainless Steel Screwed Flange : ASTM A 182, A 240?Grade: F 304, 304L, 304H, 316, 316L, 316Ti, 310, 310S, 321, 321H, 317, 347, 347H, 904L Duplex stainless steel Screwed Flange : UNS S31803, 2205, Super Duplex stainless steel UNS S32750 Carbon Steel Screwed Flange : ASTM A 105, ASTM A 181 Alloy Steel Screwed Flange : ASTM A 182, GR F1, F11, F22, F5, F9, F91 Nickel Alloys Screwed Flange : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy C22, C276 Copper Alloys Screwed Flange : ASTM / ASME SB 61 / 62 / 151 / 152 C 70600 (CU -NI- 90/10) C 71500 (CU -NI- 70/30) UNS NO. C 92200, UNS NO. C 83600,UNS NO C 10100 C 10200, C 10300, C 10800, C 12000, C 12200 VALUE ADDED SERVICES : Hot Dip Galvanizing Test Certificate As Per EN 10204 - 3.1 & 3.2
This is similar to a slip-on Flange in outline, but the bore is counter- bored to accept the pipe. The diameter of the remaining bore is the same as the inside diameter of the pipe. The Flange is attached to the pipe by a fillet weld around the hub of the Flange. An optional internal weld may be applied in high stress applications. Its biggest use is in high-pressure systems such as hydraulic and steam lines. DIMENSION SPECIFICATIONS AS PER THE INTERNATIONAL STANDARD ASTM, ASME, API, AISI, BS, ANSI, DIN, JIS, MSSP, NACE SIZE : ½" to 60" (As Per Customer Requirement) CLASS : 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS DIN Standard ND-6,10, 16, 25, 40 Etc. MATERIAL GRADE : Carbon Steel Socketweld Flange : ASTM A105, ASTM A 694 F42 Low Temperature Carbon Steel Socketweld Flange : A350 LF2/A350 LF3 Copper Alloys Socketweld Flange : ASTM / ASME SB 61 / 62 / 151 / 152 C 70600 (CU -NI- 90/10) C 71500 (CU -NI- 70/30) UNS NO. C 92200, UNS NO. C 83600,UNS NO C 10100 C 10200, C 10300, C 10800, C 12000, C 12200 Nickel Alloys Socketweld Flange : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy C22, C276 Duplex Socketweld Flange : ASTM A 182 UNS F 44, F 45, F51, F 53, F 55, F 60,F 61 Stainless Steel Socketweld Flange : ASTM 182 F 304, 304L, 304H, 309S, 309H, 310S, 310H, 316, 316TI, 316H, 316L, 316LN, 317, 317L, 321, 321H, 347, 347H, 904L. Alloy Steel Socketweld Flange : ASTM SA 182 F1/F5/F9/F11/F22/F91 VALUE ADDED SERVICES : Hot Dip Galvanizing Epoxy Coating Test Certificate As Per EN 10204 - 3.1 & 3.2
This is a Flange without a bore and is used to shut off a piping system or vessel opening. It also permits easy access to vessels or piping systems for inspection purposes. DIMENSION SPECIFICATIONS AS PER THE INTERNATIONAL STANDARD ASTM, ASME, API, AISI, BS, ANSI, DIN, JIS, MSSP, NACE SIZE : ½" to 60" (As Per Customer Requirement) CLASS : 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS DIN Standard ND-6,10, 16, 25, 40 Etc. MATERIAL GRADE : Carbon Steel Blind Flange : ASTM A105, ASTM A 694 F42 Low Temperature Carbon Steel Blind Flange : A350 LF2/A350 LF3 Copper Alloys Blind Flange : ASTM / ASME SB 61 / 62 / 151 / 152 C 70600 (CU -NI- 90/10) C 71500 (CU -NI- 70/30) UNS NO. C 92200, UNS NO. C 83600,UNS NO C 10100 C 10200, C 10300, C 10800, C 12000, C 12200 Nickel Alloys Blind Flange : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy C22, C276 Duplex Blind Flange : ASTM A 182 UNS F 44, F 45, F51, F 53, F 55, F 60,F 61 Stainless Steel Blind Flange : ASTM 182 F 304, 304L, 304H, 309S, 309H, 310S, 310H, 316, 316TI, 316H, 316L, 316LN, 317, 317L, 321, 321H, 347, 347H, 904L Alloy Steel Blind Flange : ASTM SA 182 F1/F5/F9/F11/F22/F91
This Flange is designed to be joined to a piping system by butt- welding. It is relatively expensive because of its long neck, but is preferred for high stress applications. The neck transmits stresses to the pipe, reducing stress concentrations at the base of the Flange. The gradual transition of thickness from the base to the neck to the wall thickness at the butt weld provides important reinforcement of the Flange. The bore of the Flange matches the bore of the pipe, reducing turbulence and erosion. DIMENSION SPECIFICATIONS AS PER THE INTERNATIONAL STANDARD ASTM, ASME, API, AISI, BS, ANSI, DIN, JIS, MSSP, NACE SIZE : ½" to 60" (As Per Customer Requirement) CLASS : 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS DIN Standard ND-6,10, 16, 25, 40 Etc. MATERIAL GRADE : Carbon Steel Weldneck Flange : ASTM A105, ASTM A 694 F42 Low Temperature Carbon Steel Weldneck Flange : A350 LF2/A350 LF3 Copper Alloys Weldneck Flange : ASTM / ASME SB 61 / 62 / 151 / 152. C 70600 (CU -NI- 90/10) C 71500 (CU -NI- 70/30) UNS NO. C 92200, UNS NO. C 83600,UNS NO C 10100, C 10200, C 10300, C 10800, C 12000, C 12200 Nickel Alloys Weldneck Flange : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy C22, C276 Duplex Weldneck Flange : ASTM A 182 UNS F 44, F 45, F51, F 53, F 55, F 60, F 61. Stainless Steel Weldneck Flange : ASTM 182 F 304, 304L, 304H, 309S, 309H, 310S, 310H, 316, 316TI, 316H, 316L, 316LN, 317, 317L, 321, 321H, 347, 347H, 904L. Alloy Steel Weldneck Flange : ASTM SA 182 F1/F5/F9/F11/F22/F91 VALUE ADDED SERVICES : Hot Dip Galvanizing Test Certificate As Per EN 10204 - 3.1 & 3.2
The Flange is slipped over the pipe or tube and welded (usually both inside and outside) to provide strength and to prevent leaks. These flanges are at the low cost end of the scale, and do not require high accuracy when cutting the pipe or tube to length. They can sometimes have a boss or hub, and can be made with a bore to suit pipe or tube. Dimension Specifications : As Per The International Standard Astm, Asme, Api, Aisi, Bs, Ansi, Din, Jis, Mssp, Nace Size : ½" to 60" (As Per Customer Requirement) Class : 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS DIN Standard ND-6,10, 16, 25, 40 Etc. Material Grade : Carbon Steel Slipon Flange : ASTM A105, ASTM A 694 F42 Low Temperature Carbon Steel Slipon Flange : A350 LF2/A350 LF3 Copper Alloys Slipon Flange : ASTM / ASME SB 61 / 62 / 151 / 152. C 70600 (CU -NI- 90/10) C 71500 (CU -NI- 70/30) UNS NO. C 92200, UNS NO. C 83600,UNS NO C 10100,C 10200, C 10300, C 10800, C 12000, C 12200 Nickel Alloys Slipon Flange : Monel 400 & 500, Inconel 600 & 625, Incolloy 800, 825, Hastelloy C22, C276 Duplex Slipon Flange : ASTM A 182 UNS F 44, F 45, F51, F 53, F 55, F 60,F 61. Stainless Steel Slipon Flange : ASTM 182 F 304, 304L, 304H, 309S, 309H, 310S, 310H, 316, 316TI, 316H, 316L, 316LN, 317, 317L, 321, 321H, 347, 347H, 904L. Alloy Steel Slipon Flange : ASTM SA 182 F1/F5/F9/F11/F22/F91 Value Added Services : Hot Dip Galvanizing Test Certificate As Per EN 10204 - 3.1 & 3.2
Coat Hook
Coat Hook
Nylon Coat Hook
Coat Hook
Coat Hook
SS Partition Clamp
SS Urinal Clamp
Ss Urinal Clamp With Cover Also
Nylon Urinal Clamp
Minimum Order Quantity : 1000 Number Features : SELF DRILLING SCREW WITH RUBBER WASHER Usage/Application : FASTENING Type of Heads : Milled Head, Centre Head, Round-head Type : SCREW Product Type : SCREW Packing Type : 100 NOS BOX Grade : SILVER Material Grade : GI Head Type : HEX HEAD,CSK SLOT ROUND HEAD Finishing : SILVER Surface Finishing : SILVER Screw Diameter : 4.2MM Head Shape : HEX HEAD ROUND HEAD CSK Coating : SILVER Place Of Origin : INDIA,TAIWAN Material : Mild Steel Carton Contain : 10 Is It Polished : Polished Quantity Per Pack : 100 Our reputation in the market is largely attributable to our precision-designed Self Drill Screw that is used for precise drilling without any effort and error.
Size : ALL Quantity Per Pack : 144 1000 Brand PATTA Keeping in mind the precise demands of clients, we offer a wide range of Metal Screws. These are ergonomically engineered from top quality components which are directly sourced from reliable vendors of the industry. Following the precise demands of clients, we offer these Metal Screws in various range, designs and dimensions. One can avail these Metal Screws in various technical specifications. Features: Varied lengths Market leading price Premium quality
Approx. Price: Rs 650 / Unit To meet the precise demands of clients, we offer a wide range of Vertical Lifting Clamps. These are ergonomically engineered using best available technologies and following international industrial standards. Our devices are applauded for their maximum durability and robustness. These can be availed in various technical specifications and range. Features: Longer service life Low maintenance Highly demanded
Approx. Price: Rs 450 / Unit We are a leader in supplying best quality Horizontal Lifting Clamps.
The polished rod clamp is of butterfly structure, it is fixed on the polished rod as retaining device for the wire hanger. It makes the pumping unit horse-head connected with polished rod through rod eye lifting device, and then the polished rod append and support the load of sucker rod string. The polished rod clamp is an important part connecting oil pump and sucker rod, it is required not only reliable, have a certain capacity, but also can not cause damage for sucker rod.
