Product: al-ztw80a sbec
Code: 3080201
1.Specification: 1.1 output :continuous current 80a , burst current 90a for 10 seconds1.2 battery cell :5-18nc/2-6lipo1.3 weight :87g1.4 bec output :5v/2a1.5 size :68*37*17mm(l*w*h)
2. Features: 2.1 extremely low internal resistance2.2 super smooth and accurate throttle linearity2.3 safety thermal over-load protection2.4 auto throttle shut down in signal lose situation2.5 supports high rpm motors2.6 power arming protection (prevents the motor from accidentally running when switched on)2.7 new advanced programming software
2ch.3ch.3.5 ch .All helicopter we can sale to you. Weight 12
RC helicopter
This helicopter is designed for indoor and outdoor flight. Emitter adopt newest 2.4g make band pair technology, could auto make band pair, separate and exact make band pair. After making pair, you can fly helicopters at same time. Features: charging time: 40-60 min. Flying time: 8-10 min. Channels: 4 ch Length: 15 inches Width: 3 inches Height: 5 inches Weight: 0.5 lb. Battery: 7.4v polymer battery / 850mah For ages: +14 Comes 8 in a box
Hello, I Hope you are keeping well . is a leading supplier of MI 17 - MI 35 new / used helicopters and spares or Overhaul kits (Military & Civil variants) / OVERHAULING MI 17 - MI 35 Helicopters
DESCRIPTION Four cylinders,horizontally opposed engine,aircooled,single magneto ignation,wet sump pressure lubrication FEATURERS 1.The ratio of power weight is higher. 2.Extremely low failure rate. TECHNICAL DATA: Maximum Power 44 kW/60 HP at 3600 rpm Displacement 1680 cm3 / 102.52 cub. in Compression ratio 8:1 Two carburetors Fuel min. octane 98 RON (Unleaded) / AVGAS 100 LL Dry weight 73 kg, plus accessories Fuel consumption 10L/hour APPLICATION: Used for fixed wing, manned/unmanned, helicopter, gyrocopter, sailship. OTHER INFORMATION: We can provide propellers, generators(for UAV), start-generators and other accessories.
DESCRIPTIONï Four cylinders,horizontally opposed engine,aircooled,single magneto ignation,wet sump pressure lubrication FEATURERSï 1.The ratio of power weight is higher. 2.Extremely low failure rate. 3.Turbo charger,full take off power up to 3500 meters. TECHNICAL DATA: Maximum Power 64 kW/87 HP at 3200 rpm Displacement 2424 cm3 / 147.91 cub. in. Compression ratio 8.5:1 Two carburetors Fuel min. octane 98 RON (Unleaded) / AVGAS 100 LL Dry weight 82 kg, plus accessories Fuel consumption 14L/hour APPLICATION: Used for fixed wing, manned/unmanned, helicopter, gyrocopter, sailship. OTHER INFORMATION: We can provide propellers, generators(for UAV), start-generators and other accessories.
Product Featureï 1,Designed for unmanned aerial vehicle (uav) 2,The ratio of power weight is higher 3,Extremely low failure rate Product Specificationï Power: 16 kW / 7200 rpm Displacement: 274 cm3 Weight: 7.8 kg with magneto ignition Fuel: 90 RON (unleaded) / AVGAS 100 LL - oil mixture 1:25 for mineral oil or 1:50 for synthetic oil Optional accessories:Electric starter,Shielded ignition leads,Exhaust stacks (stainless steel 150mm long, 2 needed),Generator 28V/1200W2,Generator coupling kit (engine side),Certificate of Conformance / Test - run Application: Remote control airship,fix wing plane,helicopter,sailship etc. Other Information: We can also provide propellors for L275E engine,such as 27*20,28*20,34*10,34*12,also we can provide generator and other accessories.
Bearings for aircraft of russia & china aircraft Mi-17/171;an-12/24/26/32;ka-35;il-76; y-12; k-8;f-7;cj-6, etc Bearings for aircraft of russia & china aircraft
The talon fastener was designed to give the end user the ability to install a bolt where access to the rear of the bolt is unavailable for the placement of the nut (i.E. Walls, tanks, floors, etc). For additional safety, the talon fastener has a built in, spring loaded locking device to prevent accidental release of the fastener after installation. This provides the end user with a visual indication when the talon fastener is properly engaged. Having the ability to provide quick and secure attachment points, utilizing a single person, equates to savings by reducing material and labor cost.
