3D Wheel Alignment Aligner Equipment Ds-953D

Image acquisition: A digital camera Signal Processing: DSP Measuring system: 2 group industrial camera, four goals reflex plate and special software Measuring principle: The camera takes a candid photograph of the dynamic car wheel, car body and level surface on the speed of 0.5 seconds/times. The geometrical image will be contrasted with a predetermined standard image, and then got the four-wheel location data through calculation formula. Measurement methods: 1. got a complete measurement through lifting vehicles 2. All the measurements completed through moving vehicles 3. The static measurement (not open) Help system: 1. Built-in help operation software, help users grasp and used correctly 2. Built-in 3d adjusts software, help users adjust and repair the chassis fault effectively and quickly. 3. Guide menu, easy to find the models data. Stable accuracy: 1.The stability of 3D product has been raised with his simple structure, advanced technologies, non light, temperature disturbance and non hidden faults of electronic, circuit, batteries of traditional four-wheel alignment. 2. Measurement precision of 3D is more stable and reliable with non requirements of the accuracy for clamp, rims and lift platform. 3. Non 0 points shift in 3D product, so only one calibration for forever use. RangePrecision Accuracy Total toe 200.02 Individual Toe 100.02 Camber 90.01 Caster 200.04 KPI 200.04 Setback 50.01 Thrust Angle 50.01 Track width 2600mm0.5mm Wheelbase 3800mm0.62mm Voltage 110/220V. Plywood case.

Power supply: 110/220V Location Theory: Thrust Line Means of Communication: Bluetooth communication / Cable transmission Measurement: CCD digital image measurement Signal Processing: DSP Range Precision Accuracy: Total Toe 400.02 Single Toe 200.02 Camber 140.01 Caster 200.04 Kingpin Inclination 200.04 Thrust Angle 100.01 Setback 100.01 Inclusive Angle 400.05 Tread Width 2.2m1mm Wheelbase 3.6m1mm. Function: 1.Four-point manual/automatic ROC optional features 2.1420measuring range of kingpin optional features 3.With A4A6A8 and B5 toe curve special measurement and adjustment software 4.Operation with Chinese timely reminder 5.With the new data increasing menu 6.New wave filtering technology to enhance the stability of device 7.With data memory function£¬supporting to measure and adjust the camber in the vacant state 8.CCD permits measuring at a large range and automatically measures Kingpin parameters 9.The host computer and measuring head, with dual electronic level settings, can monitor the level of measurement state of measuring head all the times, and ensure accurate measurement data reliability 10.With measurement function of tread difference, wheelbase difference and declination axis 11.Supporting the function of swapping measurement head and calibration-free 12.With measurement function of unit rod and dual rod 13.With customer file database, can renew and access to the customer information, It's useful for users to manage customer's resource 14.Improved circuit design, using environmentally friendly batteries, can be used continuously for 5-8 hours 15.The head and computer, with dual operating system, can realize that synchronization purpose of ¡°up¡±and ¡°down¡± is up to you completely. Cabinet:1040*790*1320mm Spare parts:1030*1020*960mm.

Power supply: 110/220V Location Theory: Thrust Line Means of Communication: Bluetooth Communication Measurement:CCD digital image measurement Signal Processing: DSP Functions: 1.With the A4A6A8B5 special toe measurement and adjustment software 2.Quick-type positioning system, optional measurement of the process and positioning the way, the quickest way to just 6 seconds 3.There are 20,000 Chinese and foreign models vehicles models database, and are free to upgrade 4.Can automatically switch to Kingpin measured parameters, without E-corner disc 5.Supported in lifting the state of the next adjust camber function 6.Can measure tread difference and wheelbase difference 7.With tips and guide operating system 8.The level of built¨Cin electronic device, and has prompted the level of error function 9.The measuring head can be interchangeable and calibration for free 10.Test head with self-diagnosis function and electronic clear. RangePrecision Accuracy Total Toe 200.03 Single Toe 100.03 Camber 100.02 Caster 100.04 Kingpin Inclination 100.04 Thrust Angle 90.02 Setback 90.02 Tread Width 2.2m1mm Wheelbase 3.6m1mm Plywood case.

Supplier: New and used tires for a variety of vehicles.

V880 3d wheel aligner The measurement principle: Forming the basis plane and position of the quadrilateral by the four wheel centers, constituting the angle of the wheel aligner by the geometric relationship between the wheel plane and wheel plane with the basic plane together. Calculating the axis of kingpin by the wheel rotation axis during the wheel steering. Constituting run-out compensation by the wheel rotation axis while vehicle moving and angle changes of the wheel plane geometry. Four target reflectors are mounted above the vehicles four rims then scrolling wheel and continuous shooting the geometry of the reflective target board by the camera, analyzing the changes of the geometry by computer then to get the corresponding positional parameters of the wheels and chassis and so on. The technology is the use of machine vision technology and computer information processing technology. Product features: Two industrial ccd digital camera, four target goals The carts dynamic measurement. Can realize the automatic compensation of the positioning data, so that get more accurate measurement data Simple operating. Four target plates hanging on the rim then push the car to complete the traditional positioning kingpin measurement except the kingpin No need periodic calibration. Calibration is completed before leaving the factory. Measurement and the tilt are independent of impact of level of platform No electronic components on the target reflector board, very low failure rate. Lifting measuring range up to 1 meter.

KWA-300 3D Wheel Aligner is a precision measurement instrument designed to measure the wheel alignment parameters and compare them with the specifications provided by vehicle manufacturer. It also gives instructions to the user for performing corresponding adjustments so as to get the best steering performance and reduce tire wear. Functions and Features Complete test: The KWA-300 3D Wheel Aligner can be used to measure the most wheel alignment parameters, such as front wheel toe-in, front wheel camber, caster, Kingpin inclination, maximal steering angle, thrust angle, toe-out on turns, rear wheel toe-in, rear wheel camber, thrust angle, wheelbase difference, tread difference, etc. Brand new 3D computer vision measurement: Automatically test the aligning angles with high performance camera. Positive targets: There are any electronic elements inside the targets, and no cables between the targets and the main unit, so the targets are easy to be fastened on the wheel clamps. Provides many kinds of auto test processes and diagram operating interfaces, very simple and clear to operate; The whole test process can be performed automatically, and there are some humanity tips on the corresponding interfaces. Complete databank: Wheel alignment data of over 20, 000 vehicle models is stored in the system. User can also add new data to the databank. Automatically record the history data, easy for customer measurement. Standard printer to print test result. Provide real-time help with help system.

3D wheel aligner Model:SX-G6 Characteristics of 3D Wheel Alignment 1.3D cameras alignmentùBased on the car and not influenced by the platform 2.Measurement systemùequipped with double digital cameras and four target disk, supplying revolutionary measurement mode 3.Target diskùThere is no electronic components, so the wheel alignment will not has a component failure problem. 4.Equipment Calibration - once calibration before delivery, workable immediately after installation, no need for periodic calibration 5.Measurement progressùno need to compensate for steel ring , the precise eccentric compensation will be just once pulling or pushing the car back and forth 6.Software systemùùEasy to operate, complete conventional basic parameters within two minutes ,significantly faster than conventional aligners 7.Daily MaintenanceùEasily maintenance , download and upgrade freely for the model data. Technical Specification: Measurement project Accuracy Measurement range Measurement project Display accuracy 1¦/1mm Display accuracy Camber ¦2¦ ¦10¦ Camber Caster ¦6¦ ¦20¦ Caster Kingpin Inclination ¦6¦ ¦20¦ Kingpin Inclination Toe-in & Toe-out ¦2¦ ¦20¦ Toe-in & Toe-out Set back ¦2¦ ¦5¦ Set back Thrust angle ¦2¦ ¦5¦ Thrust angle Wheel Deviation ¦2mm Wheel Deviation Axis Deviation ¦2mm Axis Deviation Measurement project Accuracy Measurement range Measurement project. Woodedn carton.

Vision based 3D Imaging technology using 2 High Performance SI (Scientific Image) Camera Simultaneous Front and Rear wheel alignment (4,4) Push Pull Runout /Setback / Thrust angle compensation Lift level compensation at adjustment level Unlimited memory for vehicle specifications Option for selection of vehicle specification during alignment Power failure data protection Automatic tracking of Left & Right turns for Caster/Kingpin measurements Adjustment of Camber in wheel Jacked-up position & Toe curve measurement Rear Setback & Track width difference, Toe adjustment in single Tie rod vehicle, Vehicle geometry measurements Effortless Toe (Easy Toe) adjustment program Camber measurement at Zero Toe Drag link adjustment Toe out on Turns & Lock angle measurements Animated pictorial display of angles during alignment Zoom in option for live parameters Two Color Bar display for adjustment of all angles Quick Wheel Alignment program by user defined Data Manager Software for storing alignment results Customer Address in printout & customer data edit option 3-D Pictorial & Two color text printout Multi-lingual program & Voice prompt Two wheel Alignment program by fixing only front two target plates