Metallized microwave ferrite substrate for antenna use
Metallized YIG Microwave ferrite substrate Technical requirements: 1- The Ferrite Thickness should be 0.37mm. In the process of ferrite production, fine grinding method should be used. The surface of the ferrite should be polished (To reduce the roughness). Material:CY1780 2- Use a soft gold coating. Clad layer: Cu1m4mAu2.5m5.7m. The plating thickness should be 8~10m(Red area ). 3- The bottom side will be attached to a Gold plated carrier by soldering. The solder paste model can be Pb63Sn37. The carrier material is Iron. Clad layer: Cu36mNi14m Au12m. The final carrier dimensions (after plating) are 12mm X 9mm X 0.5mm. 4- The resistive layer should be 75 Ohm/Sq. The final resistor should be 50 Ohm (+/-10% tolerance) (Green area)
Metallized YIG Microwave ferrite substrate Technical requirements: 1- The Ferrite Thickness should be 0.37mm. In the process of ferrite production, fine grinding method should be used. The surface of the ferrite should be polished (To reduce the roughness). Material:CY1780 2- Use a soft gold coating. Clad layer: Cu1 m 4 m Au2.5 m 5.7 m. The plating thickness should be 8~10 m(Red area ). 3- The bottom side will be attached to a Gold plated carrier by soldering. The solder paste model can be Pb63Sn37. The carrier material is Iron. Clad layer: Cu3 6 m Ni1 4 m Au1 2 m. The final carrier dimensions (after plating) are 12mm X 9mm X 0.5mm. 4- The resistive layer should be 75 Ohm/Sq. The final resistor should be 50 Ohm (+/-10% tolerance) (Green area)
Microwave ferrite substrate: Size:60*48*1mm;60*48*0.5mm;48*30*1mm;48*30*0.5mm SATURATION MAGNETISATION (GAUSS):1750-1800 DIELECTRIC CONSTANT:15,0 ±5% DIELECTRIC LOSS TANGENT: 0.0002 CURIE TEMPERATURE (NOMINAL VALUE)(°C):280 LINE WIDTH (Oe):25 SPIN WAVE LINE WIDTH (Oe):2 FINISH: CLEAN.
Microwave ferrite substrate: Size:60*48*1mm;60*48*0.5mm;48*30*1mm;48*30*0.5mm SATURATION MAGNETISATION (GAUSS):1750-1800 DIELECTRIC CONSTANT:15,0 ±5% DIELECTRIC LOSS TANGENT: 0.0002 CURIE TEMPERATURE (NOMINAL VALUE)(°C):280 LINE WIDTH (Oe):25 SPIN WAVE LINE WIDTH (Oe):2 FINISH: CLEAN.
Supplier: Modern and antique car parts, fiber optic parts, ferrule sleeve, antenna accessories, metal stamping/ rolling, plastic, rubber injection, electric parts
Supplier: Heavy machinery, tools, metal products, screws, antenna, cable, exercise bike, relay, GPS, tool and die, connector, mold, mould, wire, plastic film, light, wiring harness, pump, precision part, switch, power supply, engine, terminal, inverter, converter, casting, machining, inductor, transformer, motor, plastic sheet, plug
Type: 0.1 2 12-18mm Ferrite Core Rod Coil./customized your own size Copper Wire Diameter: available wire copper size 0.0112-0.026MM(support customized) Coil Diameter:1 2.3MM(support customized) Coil Turns:20000TS( Support customized) Coil Shape:tube/oval/rectuangle/ roud( support customized) Bobbin:Plastic,Ferrite Rod/Magnet etc Customized Ferrite/Rod: Size,Shape customized Inductance:300â??500mh Support Customized Cost: USD 0.1-1.5/pcs With volume 10,0000 monthly. ChengPin Technology can using 0.0119mm wire diameter to manufacture 1-3mm mirco acoustic inductors Customized all size,shapes,inductance/resistance based on your requirements.
Supplier: Antenna, pogopin, probe pin, test pin, spring pogo pin, metal connector and components
