Radiation Measurement Instruments
Radiation measurement instruments provide accurate radiation measurements in a variety of applications. From performing handheld gamma radiation measurements to measuring alpha and beta, radiation detectors make it easy to perform the measurements that are critical to any radiation safety program. These radiation monitoring instruments provide flexible options for most basic radiation detection scenarios.
1. What are radiation measuring instruments?
Sources of ionizing radiation have important and indispensable uses in various industries to derive maximum benefit from their applications. To ensure radiation safety for radiation professionals, patients and the public; good radiation safety practices should be followed. The most important practice is to use radiation measuring instruments to measure the radiation in and around the source.
2. What are the types of radiation measuring instruments?
The main types of radiation measuring instruments are: Surveyor, Dose Alarm Instrument, Radiation Monitoring System, Contamination Detector.
3. What are the important factors to be considered in the maintenance of radiation measuring instruments?
Instruments should be kept in the best condition.
Periodic calibration should be carried out as recommended by the authorities.
If the instrument is repaired (or) the detector is replaced, the radiation measuring instrument must be recalibrated.
4. Where can these radiation measuring instruments be calibrated?
Calibration cannot be done in any laboratory. The laboratory must be accredited by AERB (Atomic Energy Regulatory Board of India).
AERB has further made it stringent that the laboratory must be accredited by an auditing body i.e. NABL.
Such laboratories are required to calibrate the radiation measuring instruments at regular intervals.
Established wide range of measuring instruments compactable for digitization: CMM - Zeiss make, portable CMM - Faro make, profile projector and testing equipment for special processes.
Measuring Instrument
# Callipers Measuring range of 0-1000 mm; # With and without fine tunning; # Material – constructional or stainless steel; # Mat chromed scale; # Reading – 0.1 and 0.05 mm. # Special callipers 3-point vernier calliper; # 5-point vernier calliper; # Marking-off vernier calliper; # Weld seam gauge; # Other types. # Vernier depth gauges Measuring range of 0-500 mm; # Reading 0.1 and 0.05 mm; # Material – constructional or stainless steel; # Mat chromed scale. # Micrometers Measuring range of 0-25; 25-50; 50-75; 75-100 mm; # Reading – 0.01 mm; # Measurement reading surface of hard alloys (carbide). Range 0-25 mm. # Coordinate small size tables One-coordinate; # Two-coordinate; # Three-coordinate; # Stroke along the coordinate: 0-25 mm # Measuring stands Type A2 – with magnetic switch at the base; # Type A4 – with cast-iron base and T-shaped groove; # Type B3 – with square-riffled table; # Micrometer holder. # Smooth gauges Plug gauges – one sided; # Plug gauges – two sided; # Snap gauges. # Thread gauges Thread plug calipers – one sides; # Thread plug calipers – two sides; # Thread ring gauges. # Smooth rings Reference rings; # Setting rings Range: 6-150 mm. # Squares and rulers Flat squares; # Squares with base; # Checking rulers; # Templates. # Angle gauges Protractor with lock screw Range 80x120 – 300x500 mm; # Protractor with sliding rod Range 120x240 – 300x500 mm Reading - 1° # Marking-off tools (scribers) Straight scriber – one sided (with knurled handle); # Bended tip scriber – two sided (with knurled handle); # Trammel for tracing and marking with small base; # Vernier caliper with two needles and fine adjustment; # Height gauge with fine adjustment.
For all kinds of devices working with electricity; You can use the Wavecontrol WP50 Low frequency probe to measure the electrical field and magnetic field effect created by energy transmission lines (low medium high voltage transmission cables), transformers, electrical appliances etc.
HD Observation Machine Advantages Original colour HD Graphics comparison Take screenshots Large viewing area Easy to communicate USB stick storage Depth measurement Local zoom Arbitrary labelling Raster measurcmcnt Mouse measurement Simple operation Specifications Power supply voltage: 220V Frequency: 60HZ Display size: 24-inch 2K display (can be upgraded to 27-inch 4K display) Resolution: 1000~3000W industrial pixel Magnification: 0~80/160/250 times Maximum field of view: 90x50mm Measurement accuracy: 0.01/0.005/0.001mm Measuring stroke: desktop HD observation machine (X-65/Y-65)
Ultrasonic Thickness Meter RUM7401 1.Spec: Used for measuring thickness and corrosion of pressure vessels, chemical equipment, boilers, oil storage tanks,etc.in industries of petroleum, shipbuilding, power station, and machine manufacturing. 2.Features: * Using the latest high performance and low power consumption microprocessor technology. * Bidirectional measurement, for materials within measurement range, thickness is measurable with know velocity, Conversely velocity is measurable with know thickness. * Automatic memory material code and sound velocity value, convenient to use. * Coupling symbol indication. * Use USB/RS-232 data output to connect with PC. * Provide Bluetooth data output choice. 3.Specifications: Display: Large Screen LCD Housing Material: Aluminum Alloy Measuring Range: 0.75~400mm(45#steel,Depend on Probe) Resolution: 0.01mm/0.1mm/0.001 inch Accuracy: ±(0.5%n+0.05) Sound Velocity: 1000~9,990m/s Lower Limit of Pipes: �¦15x2.0mm �¦20x3.0mm(Determined By Transducer) Operating Conditions: Temperature: 0~40�º; Humidity:
MDC-K120 Slab Mold Taper Measuring Instrument Overview The taper of the narrow face of the mold has an important influence on the quality of the casting billet. Excessive taper will cause the mold to squeeze the billet shell, and a small taper will increase the air gap. With the continuous increase of the requirements of the casting billets quality and the continuous introduction of high-precision molds, the current taper measuring instrument in the domestic market generally have low measurement accuracy and complex measurement methods, which restrict the development of production. The new-generation taper measuring instrument developed high-precision inclination sensor, combined with ultra-low power consumption processor, which can quickly and accurately measure the actual taper value of the narrow copper plate of the mold. The instrument is fully functional, easy to use and suitable for slab molds of various lengths. Most of the current slab molds are single-taper, a narrow flat copper plate. The taper value required for production can be achieved by adjusting the angle between the narrow copper plate and the direction of gravity. The taper measuring instrument directly measures the angle between the narrow copper plate and the direction of gravity. According to habits and production needs, the angle is converted into the value of one-sided shrinkage of the upper and lower ports. The main features 1. Easy to calibrate, stable performance, easy to operate 2. Self-supporting, self-aligning, self-balancing 3. High measurement accuracy 4. LCD data reading 5. Fast response, real-time display reading 6. Adjustment of dynamic intelligent system 7. Lithium battery power supply, suitable for on-site use of mobile operations 8. The continuous measurement time is more than 36 hours 9. The sensor adopts multiple protections to meet the needs of on-site harsh environment measurement 10. The weight of the whole system is less than 3.8 kg, and it is equipped with a set of zero-point calibration table, which is convenient for on-site installation and measurement 11. Applicable to various arc, parabolic and straight molds The performance and index 1. Measuring range: 3 3 (measurement length can be customized according to users needs) 2. Measurement accuracy: 0.01mm 3. Temperature range: -25 85 4. Linearity deviation: -0.03mm 0.03 mm 5. The longest usage time after fully charged: 36 hours 6. The longest storage time after fully charged: 2 months The main components 1. Measuring instrument: central measurement and control unit, measuring sensor 2. Measuring stand 3. Standard table: standard surface, support frame, spirit level
MDC-K400 Square and Round Billet Taper Measuring Instrument The product description The square, rectangular and round billet taper measuring instrument adopts high-precision displacement sensor as the measuring element, which has high precision and good repeatability. The measuring trolley ensures that the measuring sensor is in the correct position. The round copper tube taper measuring instrument ensures that the sensor is located at the diameter of the measuring section circle. Due to the characteristics of the round copper tube, one measurement action can measure multiple physical quantities on the copper tube section. The square billet taper measuring instrument can arrange measuring points in four directions and can measure straight or curved surfaces respectively, while the rectangular billet taper measuring instrument needs to install six measuring points to measure the taper of multiple faces at the same time. The product features 1. Use a high-precision vector displacement sensor 2. Battery powered, compact and flexible, easy to carry and use, strong anti-interference ability 3. Use wireless communication function and CRC check technology to ensure no error code and accurate signal transmission 4. SPI all-digital interface, programmable 16-bit A/D converter, with program-controlled digital filtering and program-controlled lossless amplifier inside, fully meeting the measurement requirements 5. High-power rechargeable battery, long standby time, suitable for on-site use of mobile operations 6. The measuring body and the display instrument are connected by wireless WIFI communication, which is easy to use The performance and index 1. Measurable copper pipe length is more than or equal to 1200mm, the measurement range of straight surface and arc surface displacement is 0-10mm, and the measurement cavity size can be customized according to user needs 2. The measuring range of straight face and arc face displacement is 0-10mm, and the measuring accuracy is less than or equal to 0.01mm 3. It can measure single taper, multi-taper, parabolic taper, continuous data acquisition, and continuous working time not less than 72 hours 4. Use wireless WIFI communication technology and CRC verification technology to ensure no error code and accurate signal transmission 5. Operating temperature of the product: 25 85 6. Power supply: 12V rechargeable battery, continuous measurement time is no less than 16 hours, standard USB interface The components of the product 1. A set of measuring trolley 2. Dedicated charger 3. Portable computers and wireless transceivers 4. Data processor discriminating software 5. Calibrator 6. Integrated transceiver system
Automatic quantitative packing scale is designed for quantitative packaging, which is divided into doAutomatic Quantitative Packing Scaleuble bucket packing scale and single bucket packing scale. Double bucket packing scale adopts the integrated structure, and has proper height, compact structure, efficient energy conservation, novel appearance, simple installation, convenient maintenance. The system quantitative precision is two thousandths.
