pump impellers are interchangeable with AH/HH/LM pump impellers, The Impeller is one of the most important parts for slurry pump. Centrifugal slurry pumps need impeller to produce the centrifugal force which transfer the . The centrifugal force is produced by the impeller which rotates to a certain speed, As main rotating component which normally has vanes to impart the centrifugal force to the liquid, Usually, slurry pump impellers have a plain or a Francis type vane.
11 inch Impeller 19121-70-30 is used for 6x5x11 Mission Magnum Centrifugal Sand Pumps.
provides 19121-xx-30 impellers for Mission Magnum centrifugal pump 6x5x14:
19121-70-30 Impeller 6 x 5 11 inch
19121-80-30 Impeller 6 x 5 12 inch
19121-90-30 Impeller 6 x 5 13 inch
19121-A0-30 Impeller 6 x 5 14 inch
Fully open impeller, best design for the chemical process industries services. Ideally suited for corrosives and abrasives, handles solids and stringy fibers with ease. Allows for simple restoration of clearances when wear takes place. Back pump-out vanes reduce pressure on the shaft seal, reduce axial thrust on the bearings.
Part size cast into the impeller. This makes part identification easier.
Impeller gasket in included with impeller
All impellers are dynamically balanced
Offered Hard iron and other materials upon request
Product Specification
Power Range : 1.0 HP to 2.0 HP
Operating Speed : 0 - 3100 RPM
DC Power Range : 900 Wp - 2000 Wp
DC Voltage Range : 70 Vmp - 110 Vmp
Head Range : 30 Mtr - 90 Mtr
Discharge Range : 8000 LPD - 30000 LPD
Type of Duty : S1
- Zero Running Cost
- Less Maintenance
- Eco-Friendly
- Simple Installation
- Pollution Free
Material Of Construction - Motor
Part Grade
Mechanical Seal : Graphite Ceramic
Motor Shaft : Stainless Steel
Motor Body Pipe : SS-304
Lower Hosing : Aluminum
Diaphragm : High Nitrile butyl rubber
Top Cap : Stainless Steel
Bottom Plate : Stainless Steel
End Cap : Stainless Steel
MATERIAL OF CONSTRUCTION SCREW (HELICAL) PUMP
Part Grade
Outlet : SS-304
Suction : SS-304
Outer Shell : SS-304
Rotor Screw : Stainless Steel
Stator : Rubber Coated Alloy
MATERIAL OF CONSTRUCTION â?? CENTRIFUGAL PUMP
Part Grade
Check valve housing : SS-304
Check valve : PC
Suction : SS-304
Outer Shell : SS-304
Impeller : POM
Bowl : PC
Pump Bush : NBR
Pump Sleeve : Stainless Steel
Pump Shaft : Stainless Steel
Coupling / Pump Couple : Stainless Steel
Falcon Dlx. 250 mm ( 9 & 10) Borewell Submersible Pumpsets are powered by water filled, rewindable submersibleMotor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressureand rigidly locked in stainless steel stator shell. T-Bolt design in all motor ensures rigid construction.
Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow MRS series 27Mtr head per stage in radial flow series.
- FG 250 Cast Iron Bowl with CED Catted and SS-304 Grade Impeller in Mix flow FMC Series 22Mtr head per stage in
Mix flow series.
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads.
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set.
- Dynamically balanced rotating parts ensures minimum vibration and longer life.
- Designed for wide voltage fluctuations.
- Motor portion covered with corrosive resistance Stainless steel (SS 304) shell.
- More durability and hygiene & High operating efficiency.
- Specially designed thrust bearing to withstand high axial thrust load.
- Extremely hardwearing water lubricated bearing.
- Thread type motor construction ensures service feasibility.
- Designed for wide voltage operation.
- Best alternative for JET & Compressor pump set.
- Additional intermediate bearing in higher stage pumps.
Specification
- Power Range : 55 kW to 112 kW (75 HP to 150HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Speed : 2900 RPM
- Head Range : 12 mtr. To 300 mtr.
- Discharge Range : 3600 LPM to 960 LPM
- Outlet Size in Inch : 4.0" & 5.0"
- Degree of Protection : IP 58
- Maximum Starts Per Hour : 10 Times
V4 Borewell Submersible Pumpset
Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410.
Salient Features
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and
Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.
Specification
Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP)
- Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply.
Single Phase available in 0.5 HP to 5.0 HP
Three Phase available in 1.0 HP to 6.0 HP
- Speed : 2880 RPM
- Head Range : 10 Mtr. To 340 Mtr.
- Discharge Range : 450 LPM to 12 LPM
- Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0
- Degree of Protection : IP 58
- Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph
- Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs,
2.2kW, 7.5 kW -1500 lbs.
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph
Direct Online (D.O.L)
- Maximum Starts Per Hour : 20 Times
Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410.
Salient Features
- Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.
Specification
- Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP)
- Version : Single Phase 160V to 230V, 50Hz, AC Supply
- Speed : 2880 RPM
- Head Range : 14 Mtr. to 96 Mtr.
- Discharge Range : 70 LPM to 15 LPM
- Outlet Size in Inch : 1.25"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m�²/sec (max.)
- Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset
Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410.
Salient Features
- Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell
- More durability and hygiene
- High operating efficiency
- Specially designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps.
Specification
- Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP)
- Version : Single Phase 160V to 230V, 50Hz, AC Supply
- Speed : 2880 RPM
- Head Range : 14 Mtr. to 96 Mtr.
- Discharge Range : 70 LPM to 15 LPM
- Outlet Size in Inch : 1.25"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
