Ritver Tweed Grey Primer Is A Special Primer With Moisture Sealing Qualities
Ritver tweed grey primer is a special primer with moisture sealing qualities
Ritver Synthetic Grey Oxide Primer
Description Two component Epoxy based anti corrosive primer pigmented with Zinc Chromate as corrosion inhibiting pigments. Recommended Use :- It is recommended as primer on M.S surface for original equipment manufacturing as well as for process industry as in various fertilizer, refineries, petrochemical, chemical and other plants, applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application. Physical Data COLOUR : Assorted FINISH : Matt SOLIDS BY VOLUME : 40 ± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS : SURFACE DRY : 60 90 minutes (At 65% Relative Humidity & at 30�°C) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy thinner 190 POT LIFE : 4 hours min at 30 C RECOMMENDED DFT : 30 - 40 au. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats. Application Method Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application :- By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application For Conventional Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Nozzle Orifice : 1.2 -1.4 mm Nozzle Pressure : 40-70 psi For Airless Spray application :- Thinner : Epoxy Thinner 190 Addition : 10-15% Addition : Max 5% if required Nozzle Orifice : 0.37- 0.42mm Nozzle Pressure : 1400-1800 psi
Nc Grey Primer For Vehicles
NC Wood Primer White/grey For Pigmented Wood Surfaces
Epoxy Primer Grey is a two pack polyamide cured primer generally used for epoxy system on masonry surface and cement works. PROPERTIES Colour : Grey Finish : Matt Theoretical Coverage 6-7 m2/lit on masonry surface Spreading rate is theoretically calculated and can be effected by substrate preparation thinning and methods of application. Solids (volume) : 24�±2% Curing time : 3-6 hours at 25 �° C Full cure : 7 days Flash point : 25 �° C (ISO 367 â??83) Specific gravity : 1.00 when mixed A+B Pot life : 4 hours at 25 �° C Mixing ratio : 4 parts base"A" : 1 part hardner "B" Solvent : Epoxy thinner. High temperature will accelerate dry times and decrease pot life; lower temperature will lengthen cure times and slightly increase pot life. Normally Tollens Epoxy primer grey A+B mixing pot life is 4hrs.As a diluent use Tollens Epoxy thinner 15 â?? 25 %.
Description Two component metallic zinc rich epoxy high performance primer. Recommended Use :- The zinc pigment in dry film renders excellent protection to steel structure, tanks, bullets, dam gates, pipelines, plant equipments, jetty, etc. in both interior and exterior exposed conditions of fertilizer units, chemical plants, steel plants, cement plants, pulp and paper industries, ports, power plants, petrochemical and pharmaceutical industry, transformer, machines & other heavy duty OEMs. It also provides cathodic protection to steel and gives good resistance to corrosion at local damaged areas. It is useful in heavy-duty protective paint systems. It is recommended not to expose the primed coat alone to chemical and saline atmosphere for a long time. Physical Data COLOUR : Grey FINISH : Matt SOLIDS BY VOLUME : 50 �± 3% THEORETICAL SPREADING RATE : 10 sq.mt / ltr at DFT of 50 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (at 30�°C & at 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to minimum Sa 2 1/2 Standards is recommended with a profile of 35 - 75 microns. The surface should be absolutely dry and salt free before application. The primer should be applied preferably immediately or within 4 hours of blasting. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30�°C RECOMMENDED DFT : 30 50 µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : Infinite COMPATIBILITY : Compatible with Epoxy, PU, Chlorinated Rubber intermediate/finish coat.
Supplier: Premium Enamels, Synthetic Enamels, Furniture Enamels, Hammertone/hammertex Finishes, Metallic Texture Finishes, Knifing Putties, Red Oxide Primers, White Primers, Green Primers, Yellow Primers, Grey Surfacers, Brown Primers, Greenboard Paint, Blackboard Paint, Pink Surfacers, Aluminum Paints, Gold Paints, Clear Varnishes, Insulating Varnish, Auto Finishes, & Water Based Exterior & Interior Finishes.
TOA Primer Surfacer Grey Spray No.56 is the special primer to highlight topcoat for long lasting and durability - Formulated by high quality concentrated resin - Used for exterior and Interior - 2 nozzles, normal and unique adjustable nozzles - Able to spray upside down - Good for all surfaces : wood, steel, and plastic - Excellent durability , quick drying, and good adhesion
