Stand alone Managed 10/100/1000Base-Tx to 10/100/1000Base-Fx Media Converter
SUN Telecoms stand alone Ethernet Media Converter is offers a cost-effective product to transmit distances up to 120km (Single-mode fiber). It makes it easy to incorporate the advantages of fiber-based connection technology in a managed Ethernet/Fast Ethernet network. Integrated Auto Cross-over MDI/MDI-X and NWay capabilities make it simple to deploy within a network. Also, the í¦hot-swappableí¦ design is ideal for scaling the system up or down quickly.
Features:
Web, SNMP, Console management
Hot-swappable module
Available with ST, SC, or WDM Simplex SC single-fiber connectors
Auto MDI/MDI-X on copper port
Auto-negotiation on copper port
LED status for Link/Activity, LFS, 100, Loopback, and Full Duplex/Collision
Link-Fault Signaling illuminates to indicate link failure
Link-Fault Signaling function can boot up redundant link if network is installed with primary and redundant link
Local and remote loopback
Parameter
Specifications
Access mode
10/100mbps
Standard
Ieee802.3 10base-t ethernet, ieee802.3u, 100base-tx/fx fast ethernet, ieee802.3x flow control, ieee802.1q vlan, ieee802.1p qos, ieee802.1d spanning tree
Wavelength
850nm/1310nm/1550nm
Transmission distance
Single-fiber single-mode: 25/40/60/80/100km ; category-5 twisted pair: 100m
Port
One rj45 connector, connected to stp/utp category-5 twisted pair one fiber port: multi-mode - sc or st (fiber size: 50, 62.5/125µm) single mode - sc/fc fiber port (fiber size: 9/125µm) single-fiber single-mode - sc/fc fiber port (fiber size: 9/125µm)
Conversion mode
Medium conversion, storing and forwarding
Mac address table
I k
Buffer space
1mbit
Flow control
Full duplex state: flow control; half duplex state: back pressure mode
Delay
9.6us
Bit error rate
<1/1000000000
Mtbf
100, 000 hours
Led
Power tx link ( fiber link action ), tp link1000, tp link100, tp act ) fdx (fx full duplex mode), fx100 (fiber, with a transmission rate of 100m) tp1/2/3/4 link/act (1/2/3/4-port twisted pairs connection action) tp1/2/3/4100 (1/2/3/4-port twisted pairs, with a transmission rate of 100m)
Two 10/100m electrical ports, one single-mode or multi-mode optical port
Multi-mode transmission distance: 2km, single-mode transmission distance: 120km, single-strand double-directions /double-strand double-directions.
Set - in 1m cache, supporting 2k mac address self-learning and self-updating capability
Supports forcible execution the cross of 10m, 100m, full-duplex, half-duplex, twisted-pair and automatically adapt to connect auto mdix function directly
Supports rate control function and the rate can been controlled between nx64k (n=1~1600) to 100mbps
Supports renovate system automatically function, support system regular refresh automatically via setting time, protect from system halted
Supports management based on web, snmp, telnet or local console
Supports lld(search disconnected link automatically), llr(return alarm message when disconnected link found)
Supports llcf(report the disconnected alarm message to local network administration)
Detect and control the operational states of electrical port and optical port of the near end and the far end via interface of management
Supports open or close electrical and optical ports through via the far end network management
Supports legal maximum packet size up to 1912 bytes, support cisco, isl and vtp
Physical property:
Input power: ac 100v~220v or dc 48v
Dimension: 191mm x 110mm x 25mm
Environment requirements:
Operating temperature: 0¦-50¦
Storage temperature: -40¦-70¦
Environment humidity: 5-90%(non-condensing)
GVE-Tplus is an upgrade of GVE-T. It is based on the ASIC circuitry design technology. It is a multi-functional, multi-purpose E1/G.703 to V.35 and LAN three-in-one multiplexer, which is also knowns as the three-in-one interface converter.
GVE-Tplus can not only be set up into GVE-T, but also can distribute the whole E1 capacity to V.35 data interface, although E1 must be framed N*64Kbps(N=1--31). The work mode can be either internal clock and slave-clock, or N*64Kbps(N=1--31) external clock to achieve end-linking line.
GVE-Tplus can be set up into long-range Ethernet bridge from V.35 to LAN interface. With low cost, it is suitable for use in bridge connection which is sensitive to cost or use in LAN as a stretcher or subsection. It can learn automatically MAC address in the connected LAN and only transmit the aim address to frame in another LAN. There are more than 10000 addresses in its LAN table. And they can be updated automatically. The highest speed of filtrating and transmission is 30000 frame/second(line speed). The buffer size is 64M. The throughput delay is 1 frame. When it is used as a stretcher or subsection, it can forbid filtration so that all traffic can be broadcasted in WAN. 10baseT interface can run in full duplex Ethernet with topology and improve data throughput by eliminating filled blanks in the 64 bytes frames. Without any negotiation in V.35 port, it is specially suitable for use in satellites and other wireless broadcast.
-10/100M self-adaptive Ethernet Interface
-Support ATUO MDI/MDIX, allowing crossover cable connection or straight-through cable connection
-Selectable Baud rate between 1299bps and 921.6Kbps -Build-in WEB server, allowing users to configure their webpage easily
-Auto reconnection after a network break, ensure the reliable TCP connection for the whole network
-Support DNS, can achieve a communication using the domain name
-Compatible to SOCKET working modes (TCP Server, TCP Client, UDP and etc.), the upper layer machine software is written strictly following the SOCKET rules
-TCP modes supports multi connections, specific data sending after password verifying, allowing up to 4 user to manage a single embedded device at a same time
-Advanced security mechanisms, prevent illegal access from unauthorized visitors, provide IP verifying firewall, and up to 8 configurable IP or IP segment certifications
-Support the local and remote upgrading of the firmware;Support AT Command configuration;Support remote configuration
-16 bits ARM7 CPU;
-Ethernet: 10/100Mbps
-Protections: build-in 2KV surge protection
-Type:RS232, RS485
-Control Signals :TXD,RXD,GND
-Parity: None, Even, Odd
-Data Bit: 5, 6, 7 or 8 bits
-Stop Bit: 1 or 1.5 bits
-Flow Control: Non
-Baud Rate: 1200bps~921.6Kbps
-Compatible Protocol: Ethernet, ARP, IP, UDP, TCP, BootP
-Network Services: DHCP, DNS, PPPoE, TFTP, HTTP, UDP Broadcasting -Client/Server: Server
-Ethernet Connector: RJ-45
-Ethernet Speed/Duplex: Auto-negotiation 10/100Mbps, Full/Half duplex -Auto-MDIX: Yes -WOL: Magic Packet, Wakeup Frame, Link-Up events
-Software Tool: VSP Driver, DS Manager, Web Server
-Configuration Mode: Web browser configuration tool, Windows Hyper Terminal, Telnet, Serial port configuration
-Power Input: 3.3V DC
-Physical Size (Wí-Dí-H): 77.5í-41.7í-22.7(mm)
SFP Slot 10/100/1000M Optic Media Converter
pls contact us for more details
info[at]hongkien[dot]com
10/100/1000Base-TX to 1000Base-FX Converter
Standards: IEEE802.3 IEEE802.3U, 10/100/1000Base-TX, 1000Base-FX
Interface: 1x RJ-45 connector 1x SFP Slot
Flow Control: TEEE802.3x Flow control for full duplex mode.
Back-pressure flow control for half duplex model
10gbps media converter, 90 to 240v ac, 12v dc adapter power source type
Specifications:
Interface:
Left side:
One 10gbps rj-45 port
One 10gbps sfp + port (mini-gbic)
Right side:
One rs-232 console port (rj-45 connector)
One power jack
Wire speed cable length: up to 100m cat6a cable for wire speed transmission
Transceiver (phy), teranetics chip for 10gbase-t and net logic chip for 10gbase-r
Temperature:
