8 channels video converter Detailed Product Description 8 Channel Video Converter is a fiber optic digital multiplexer for transmitting 8 channels high quality, uncompressed digital video, 4 channels of bi-directional data and audio, 4 E1 and one 100M Ethernet over single fiber cable. Applications for this product include CCTV, video surveillance, homeland security, ITS etc. Technology Characteristic: Transport 8 channels of High quality video over one optical fiber cable Exceed RS250C Medium Haul Specification for DG, DP and SNR 6.5MHz video bandwidth, Compatible with NTSC, PAL and SECAM Uncompressed video, 8 Bit digital encoding/decoding Transmission of 4 channels of any directional audio Provide 4 channels of bi-dir data compatible with RS232, RS422/ RS485 Support 4 E1, G.703 standard One 10M/100M Ethernet compatible with IEEE802.3 Easy installation and adjustment free Transmission up to 60KM over one fiber Interface parameters: Indicators : Power, Optical Link Status Video Signal, Audio status, Data traffic E1 Alarm, Ethernet Link Status Video : Format: PAL/NTSC/SECAM Video Signal: 1Vp-p, 75ª+ Digitization: 8bits,15M Sample Bandwidth 6.5MHz DG 70dB Connector: RJ45 Data : Channel: 1~4, Bi-directional Data Rate: 0~~23.04Kbps/channel Selectable RS-232/RS-422/RS-485 Connector: RJ45 E1 Interface : Bit rate: 2.048Mb Line code: HDB3 Standard: ITU-T G.703 Connector: CC3(1.0/2.8) line impedance: 75ohm Jitter Performance: G.742 and G.823 Ethernet : Data Rate: 10/100Mbps auto detect Standard: IEEE802.3 Connector: RJ45 Auto-negotiation with half/full duplex Working Condition: Power : 220VAC/50Hz, standalone device Power Consumption : < 5W Environment Temperature : 0-50 Other Characters: Size : 434í-200í-30mm Net Weight : 900g
Product Description FE1/V.35 Protocol Converter provide conversion between ITU-T G.703 standard E1 interface and standard V.35/V.24 interface, can convert E1 channel of SDH, PDH, and other Optical Transmission Equipment or microwave, satellite Equipment to V.35/V.24 channel, Extend V.35 channel of DDN. Used widely in data communication networks, Connecting with V.35/V.24 interface of Routers and Optical Transmission Equipments without G.703 interface, realize match between different network equipments, and transparent to upper protocol layer. Technology Characteristics -> Bandwidth range is 64Kbps-2048Kbps Realize data of V.35 transparent transport in the E1 -> Support all kinds of loop function, for testing and opening conveniently -> Support network function, monitor operation condition of facilities -> Support E1 interface of unbalance 75ª+ and balance 120ª+ -> Be possession of testing function of E1 -> Support ITU-T G.703íóG.704 -> HDB3 line coding, comply indication output of route warn -> Coding rate : 2048Kbpsí+50ppm -> 75ª+ physics interface use BNC standard coaxial connector, 120ª+ physics interface use RJ45 connector V.35 Interface: -> Interface Mode : DCE -> Interface Type : DB25 -> Rate : 64Kbps-2048Kbps General characteristics -> Power : 220Ví+20% , -36 ~ -72V -> Power Consumption : < 5W -> Environment Temperature : 0íµ-50íµ -> Size : 220í-165í-35mm -> Net Weight : 900g Packing List -> FE1/V.35 Protocol Converter -> One Power cord (Note : -48v no with power cord) -> Two BNCs Coaxial Connector -> One conversion cable of DB25-M34 -> Manual book
Product Description The E1 to Ethernet protocol Converter is a device that extends Ethernet by means of telecommunication lines (E1 or E1 transport network, such as PDH, SDH, or microwave, etc.) and is also referred to "Net Bridge".It can effectively utilize free bandwidth of telecom operators' lines and can be used instantly once it is deployed, with little increased investment. Technology Characteristics -> Transparent transmission of Ethernet data through E1 lines at 2048Kbps bandwidth -> Plug and play, without any setting or debugging work -> Support automatic negotiation feature in Ethernet and full duplex/half duplex mode -> Support transmission of Jumbo Frames specified in IEEE 802.1Q and Ethernet switches with VLAN capability -> Local data frame filtering -> Provide unbalanced 75ª+ and balanced 120ª+ E1 interfaces E1 Interface: -> Support ITU-T G.703 -> HDB3 line coding, comply indication output of route warn -> Coding rate : 2048Kbpsí+50ppm -> 75ª+ physics interface use BNC standard coaxial connector, 120ª+ physics interface use RJ45 connector Ethernet Interface: -> Fully IEEE 802.3 (2000) compliant -> Bit rate: 10Mbps or 100Mbps -> Interface type: RJ45 General characteristics -> Power : 220Ví+20% , -36 ~ -72V -> Power Consumption : < 5W -> Environment Temperature : 0íµ-50íµ -> Size : 220í-175í-35mm -> Net Weight : 900g Packing List -> V.35/Ethernet Protocol Converter -> One Power cord (Note : -48v no with power cord) -> Two BNCs Coaxial Connector -> Manual book
Product Description 4/8E PDH is developed based on the VLSI chips. Relying on the advanced multiplexing technique, 4/8E PDH realizes 4/8 E1 and 100Mb/s fast Ethernet transmission with the function of Auto-Laser-Shutdown (ALS,optional). Technology Characteristics -> Transmits 4/8 E1 and one wire speed Ethernet -> Line bit rate is 150Mb/s -> Complies with ITU-T G.703 on interface and G.742, G.823 on jitter performance -> Complies with ITU-T G.802.3 on Ethernet interface and supports auto-negotiation for 10M/100M and half/full duplex working mode -> Supports VLAN and pause follow control for Ethernet -> All necessary alarm functions, supervises the status of remote terminal -> Supports E1 tributaries loop back for network fault diagnostics -> Supplies standard order wire telephone -> Supplies one customer RS232 data channel -> Supplies RS232 for equipment management -> AC 220 or DC-48 is optional -> Single board design, 1U, and 19 Inch standard Optical interface: -> Transmit Mode : Single/ Multi-mode -> Module : Single/Double Fiber -> Interface : FC/SC/ST -> Wavelength : 1310nm/1550nm -> Distance : 2Km/40Km/60Km/120Km E1 interface: -> Bit rate : 2.048Mb/s , í+50ppm -> Impedance : 75ª+ unbalanced(Declaration is needed if 120ª+ balanced required) -> Coding: HDB3, according to ITU-T G.703 -> Jitter: complies with ITU-T G.823 and G.742. Seeing appendix Ethernet interface: -> 10M/100M through auto-negotiation -> Full/Half duplex through auto-negotiation -> Connector: RJ-45 -> See appendix for Throughput, Packing error rat, Delay, and others Order wire interface: -> Phone set: Standard 2-wire phone set -> Bandwidth: 64Kb/s -> Coding: PCM RS232 for management: -> Bit rate: 9600b/s -> Data width: 8bits -> Stop bit: 1bit -> Parity check bit: None -> Connector: DB9 (pin) RS232 for customer data channel: -> Bit rate: í_250kb/s -> Connector: DB9(pin) General characteristics -> Power : 220Ví+20% , -36 ~ -72V -> Power Consumption : < 5W -> Environment Temperature : 0íµ-50íµ -> Size : 483í-200í-44mm -> Net Weight : 2.5Kg
Product Description E1 modem is called single of E1 PDH , which can connect the data one port E1 or one port RS232 to the optical interface . the equipment is wildly used in the mobile phone net station. and FTTH interface parameters the VIP optical insert . Technology Characteristics -> Realized one E1 transmitting over fiber in transparent mode -> Allow the equipment to interoperate over V.35 fiber modem and ethenet fiber modem -> Relaize one RS232 data transmitting in optical fiber line with 4800bps rate -> Have a loop setting function and easy to open and test -> Enable to manage networks and supervise equipment running and settings -> Provide unbalanced 75ª+ and balanced 120ª+ E1 interfaces E1 Interface: -> Support ITU-T G.703íóG.704 -> HDB3 line coding, comply indication output of route warn -> Coding rate : 2048Kbpsí+50ppm -> 75ª+ physics interface use BNC standard coaxial connector, 120ª+ physics interface use RJ45 connector Optical Interface: -> Rate : 4.096Mbpsí+50ppm -> Wavelength : 1310nm -> Power of optical signal output: ¿C2~-11dBm -> Receipt sensitivity : better than ¿C36dBm -> Interface : FC -> Interface mode :DCE General characteristics -> Power : 220Ví+20% , -36 ~ -72V -> Power Consumption : < 5W -> Environment Temperature : 0íµ-50íµ -> Size : 220í-165í-35mm -> Net Weight : 900g Packing List -> E1 Optical Modem -> One Power cord (Note : -48v no with power cord) -> Two BNCs Coaxial Connector -> Manual book
Features: 100/1000BASE-T1 via Marvell 88Q2112 PHY DC Voltage Requirements: 4.5-40Vdc Item will require the following items to work fully: Software, Cables, USB C cable Items Included: Intrepid Rad Moon 2 Media Converter Cable W/ power connector on one end 4500 units available
Supplier: Lcd monitors, lcd monitor panels, laptops, t shirts, shirts, polo shirts