Product introduction:
The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment.
Data:
Brand model size of interface sucking rate
Nanfeng KF25 DN25 8L/S
Product features:
1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition;
2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment;
3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands .
Replacement steps of exhaust filter:
1.After the vacuum pump stops, ensure that the system is under pressure.
2.Remove the quick release v band clamp flange on the filter.
3.Remove the oil mist filter and replace it with a new one.
Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
•Adopt numerical control, include Automatic Mode, Manual Mode, Timing Mode, Error Recording, password protection,etc.
•Be provided with automatic blow down system (Independent patent technology)
•Automatic Scale alarm(Independent patent technology), overpressure protection devices ensure the safety of the boiler
•Easy maintenance, front door of smoke box adopt articulated joint which is convenient to be open, the cleaning of close-by flue tubes become easy too.
•Safe and reliable, before leave the factory, all the boiler have to pass series of strict tests to ensure the safety and reliability of combustion and auto control devices
YYL Vertical oil/gas fired thermal oil heaters use oil or gas as fuel, the heat transfer oils is heated in the boiler furnace first, then the thermal oil will flow in the closed loop pipe to the heated equipment and then return to the thermal oil heater again, in this way, the heated object can reach a high temperature (Max. 320?) with indirect heating. It is especially suitable for industies which are flames prohibited Bidragon Oil/Gas fired thermal oil heater is high efficient compared with other heating systems. 1. Multi-passes thermal conductive structure to improve the thermal efficiency greatly 2. Horizental tubes can reduce the heat loss. 3. Thicker insulated layer to reduce heat loss by thermal radiation. 4. Intelligent control system makes biomass fired thermal oil boiler operation easier and more simple. Features of Oil/Gas Fired Thermal Oil Heaters 1. High Temperature This Oil/Gas fired thermal oil heaters can reach 320? at low pressure. 2. Easy Operation User friendly designed control system, easy to operate. 3. Low Investment Compared with steam boiler and hot water boiler, thermal oil boiler is perfect to give user high temperature in a much safer way. It cost little in maintenance and daily process. 4. PLC Intelligent Control System The PLC control system of thermal oil heaters is suitable for high temperature and high humidity environment of long-term operation.
Features of Horizontal Oil/Gas Fired Thermal Oil Boiler 1. Reasonable Structure: Multiple coil structure, Three passes of smoke and flue, weld joint with high quality. 2. Large Heating Furnace: Aopts a large combustion chamber which increases the radiation heating furnace area, this design increase the thermay efficiency and reduce the NOX emissions. 3. High Efficiency: Adopts high thermal resistance insulating layer, increase the heat transfer and thermal efficiency. 4. High Quality Accessories: All accessories such as burners, pumps, water level controller, valves and other instruments are from international or domestic famous brands. 5. Easy Maintenance: The manhole and hand hole is easy for user to maintain. Bidragon also provide life time support for clients. 6. Professional Customized Service: We provide customized service for clients who has specific requirements for the project, including design, produce and install service.
Oil and Gas Field gloves are made for protection of hands at oil and gas fields. These gloves are heat and flame retardant stitched with kevlar thread which keeps the hands safe during accidental activity during the fields.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
