LC120 thermal silicone pad is a very cost-effective general economic thermal gap filling gasket, soft with its own micro-stick, easy assembly. Under low compressing force to show good thermal conductivity and electrical insulation properties. Bedding on the gap between the heat device and the heat sink or the machine shell to extrude air to reach the full contact forming a continuous thermal conduction. Using heat sink or machine shell as a cooling device can effectively increase the cooling area to achieve a good cooling purposes. Features & Benefits: Low cost, high efficiency, cost-effective Replace the volatile pollution of the thermal grease Natural sticky, easy to install, can be reused Wide range of thickness, can fill any uneven size gap Electrical insulation Typical Applications: Communication equipment New energy vehicles / power batteries Computer Car equipment / charger Switching power supply PC server / workstation Flat-panel TV Optical drive / COMBO Security equipment Notebook computers Video equipment Any heating element and radiator For more , please kindly feel free to contact
LC120 thermal silicone pad is a very cost-effective general economic thermal gap filling gasket, soft with its own micro-stick, easy assembly. Under low compressing force to show good thermal conductivity and electrical insulation properties. Bedding on the gap between the heat device and the heat sink or the machine shell to extrude air to reach the full contact forming a continuous thermal conduction. Using heat sink or machine shell as a cooling device can effectively increase the cooling area to achieve a good cooling purposes. Features & Benefits: Low cost, high efficiency, cost-effective Replace the volatile pollution of the thermal grease Natural sticky, easy to install, can be reused Wide range of thickness, can fill any uneven size gap Electrical insulation Typical Applications: Communication equipment New energy vehicles / power batteries Computer Car equipment / charger Switching power supply PC server / workstation Flat-panel TV Optical drive / COMBO Security equipment Notebook computers Video equipment Any heating element and radiator Physical Properties: Test Item Test Method Unit LC120 Color Visual - Off white Thickness ASTM D374 mm 0.3~15.0 Hardness ASTM D2240 Shore 00 40±5~80±5 Specific Gravity ASTM D792 g/cm3 2.1 Tensile Strength ASTM D412 Mpa 0.34 Elongation ASTM D412 % 100 Tear Strength GBT 529-2008 KN/m 1.4 Breakdown Voltage ASTM D149 KV/mm â?¥10 Volume Resistivity ASTM D257 Ω·cm 8Ã?1012 Continuous Use Temp EN344 -40~150 Flame Rating UL 94 - V-0 Weight Loss @150240H % â?¤0.5% Dielectric Constant ASTM D150 @1MHz 5.41 Thermal Conductivity ASTM D5470 W/m·K 1.2 Standard sizeï¼?200mmÃ?400mmï¼?300mmÃ?400mmï¼?Customized size available; Coated with fiberglass/one side or double side adhesive/aluminum foil available
High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material. Benefits: Cost-effective, high conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect electronic devices Natural sticky, easy application, reworkable Meet ROHS and UL environmental requirements Applications: High thermal conductivity module new energy vehicles Microprocessors, memory chips and graphics processors Network communication equipment Car equipment, charger High-speed hard disk drive For more , please kindly feel free to contact rita(at)szutd.com
High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material. Benefits: Cost-effective, high conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect electronic devices Natural sticky, easy application, reworkable Meet ROHS and UL environmental requirements Applications: High thermal conductivity module new energy vehicles Microprocessors, memory chips and graphics processors Network communication equipment Car equipment, charger High-speed hard disk drive For more , please kindly feel free to contact
LCN is a kind of thermal conductive pad which do not contain silicone oil and do not volatilize and apply in optical instrument and those have sensitivity on silicone oil. There is silicone oil exuding from traditional thermal pad after heating, however, LCN absolutely solve this problem of silicone oil leakage. Whats more, the LCN series are especially fitting for filling no flat and high cumulative tolerance interface. Features & Benefits: No siloxane, no volatilization, no pollution Soft and low hardness material, good for filling High thermal conductive, low contact heat resistance Electric insulator Typical Applications: The products you are afraid of being polluted by silicone oil Optical precision equipment Laptop and projector Mobile and communication equipment, high speed large storage driver Heat pipe assembly, control equipment of car engine Telecommunication hardware and equipment High-end industrial control, and medical electronic area
Ultra-high thermal conductive silicone sheet is a high-performance heat conducting interface material made of 100% imported materials for fillingthe air gaps between the heating device and the heat sink or metal base.Its softness and elasticity characteristics enable it to be used for coveringa very uneven surface. Heat is transferred from the separation device or the entire PCB to the metal casing or diffuser to improve heat dissipationand improve the efficiency of heating electronic components and service Features & Benefits: High thermal conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect sensitive electronic devices Natural sticky, easy assembly, re-workable Meet ROHS and UL environmental requirements Typical Applications: CPU, memory module Communication hardware equipment High-speed hard disk drive Automotive engine control module Microprocessors, memory chips and graphics processors Military electronic equipment For more , please kindly feel free to contact rita(at)szutd.com
Ultra-high thermal conductive silicone sheet is a high-performance heat conducting interface material made of 100% imported materials for fillingthe air gaps between the heating device and the heat sink or metal base.Its softness and elasticity characteristics enable it to be used for coveringa very uneven surface. Heat is transferred from the separation device or the entire PCB to the metal casing or diffuser to improve heat dissipationand improve the efficiency of heating electronic components and service Features & Benefits: High thermal conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect sensitive electronic devices Natural sticky, easy assembly, re-workable Meet ROHS and UL environmental requirements Typical Applications: CPU, memory module Communication hardware equipment High-speed hard disk drive Automotive engine control module Microprocessors, memory chips and graphics processors Military electronic equipment For more , please kindly feel free to contact
LC1001 is the semi-flowing heat-resistant silicone adhesive sealant which is made of special silicone rubber material the addition of thermal powders. With excellent conductivity,V0 flame retardant grade, excellent temperature resistance, can be in the range of 60 ~ 280 Long-term use. As well as good adhesion, long term use will not fall off, will not produce Contact gap to reduce thermal conductivity, moisture-proof, anti-seismic, anti-corona, anti-leakage and aging .The properties are widely used for the adhesion and sealing of the electronic components with high thermal conductivity, which is a single part of the acetone oxime type, It can be cured silicone rubber and conforms to the requirements of ROHS REACH UL. Typical Applications High power LED lamps and lanterns, electrical power, microwave oven, electronic components and other industrial products of thermal conductive adhesive sealing, alternative thermal conductive silicone used in high-power electric module and radiator thermal conductivity between fixed filling adhesive, no card buckle screw, more reliable filling heat, simple process and lower cost. Applying Process 1.Surface clean : Clean the surface of the adhesive object and remove the rust, dust and oil. 2.Sizing: Twist the cap of the hose, squeeze the gel into the clean surface, and make it natural. 3.Curing: Place the bonded or sealed parts in the air while them to solidify naturally. Curing is a process from surface to the internal, within 24 hours (at room temperature and 55% relative humidity) will cure the depth of the 2 ~ 4 mm, if the site location is deeper that completely curing time will be postpone, especially it is not easy to come into contact with air. if the temperature is low, cure time also will be postpone .Prior to further processing or wrapping the bonded parts, it is recommended that the user wait long enough to ensure that the adhesion and integrity of the adhesion are not affected. For more , please kindly feel free to contact rita(at)szutd.com
LCK-10 silicon pad is a high-performance insulating material substrate of Kapton membrane coating with silicone and has good thermal conductivity and anti-pierce.LCK-10 is designed For those ceramic insulator substitutes like beryllium oxide�??boron nitride and bauxite. As we know that ceramic insulators very expensive and easy broken,however,LCK-10 is hard To broke and the price of it is low. Features & Benefits: Heat emission, insulation , fire prevention, shock resistance. Thermal impedance: 0.41-in2/w(50psi) Breakdown voltage can reach at 7000V Designed for the substitutes of the ceramic insulators Typical Applications: Heating power components; Automobile electronic heating module; Power module; Household appliances;
The material is heat reinforced polymer, designed to meet the Thermal conductivity and reliability demand for the thermal conductivity of high application terminal. In addition, the heat sinks performance benefits a lot from the low heat resistance. And improve the microprocessor, DC - DC converter of memory module and the reliability of power module. The phase change characteristics: the material is solid in room temperature and installation is completely convenient, used between heatsink and devices. The material can be softened and flowing when the products reach phase-change temperature to fill the devices tiny irregular contact surface. Thus, the material has the ability to fill the gap between the devices and heat sink completely, make the phase change better than non-current elastomers or thermal graphite pad and get the performance of thermal conductive silicon grease. The material is nonconductive, however, as the material has endured the phase change at high temperature, may make the metal get to the metal, so the phase change interface material cannot Features & Benefits: Low heat resistance and low stress Natural sticky, easy to use-no need to use glue No radiator preheating Flow but not silicon oil Low volatility--less than 1%
