Ferrite Magnet is manufactured from oxide material by powder metallurgical process. Its advantages include: low-cost excellent corrosion resistance, resistance to be demagnetized etc. The normal working temperature of Ferrite Magnet is between-40C and +250'C.It can be magnetized before or after assembling. Generally, Ferrite Magnet can be machined to regular shapes like segments, blocks, rings and discs etc. The normal grades for sintered Ferrite Magnets are Y10,TY25, Y30, Y30BH, Y35, etc. Advantages of Ferrite Magnet: Ferrites have isotropic characteristics, weak magnetic performance, has the same magnetic performance in any direction, multipolar magnetic charge. The main raw material of ferrite is oxides, so it is not corroded by high temperature, high humidity or chemicals (except strong acid and base); with excellent diamagnetic impedance, no flux loss before and after assembly and magnetic charging; working temperature is-40C to + 250C, poor temperature coefficient; Br temperature coefficient is-0.2% , 0.2% under Br, etc. per 1 increase; high hardness, wire cutting and grinding; ferrite is brittle and fragile during production and transportation. magnetic requirements and good for strict working environment requirement. Application of Ferrite Magnet: It is widely used in permanent magnet motor, DC motor, speaker, dry clarinet, magnetic separator machine, Magnetic Knife Holder/Rack, General Holding Devices and adsorption device and so on.
Chicory is a woody & perennial herbaceous plant of the dandelion family, usually with bright blue flowers rarely white or pink. Chicory is grown as a forage crop for livestock and the roots of Chicory is used in Beverage Industry mainly with coffee. While chicory does not have any caffeine, it does share a similar flavour to coffee, which makes it a decent substitute in times of need. Particle Size : 5mm - 15 mm Availability : Hand Cut & Machine Cut (Standard) Price Range - $450/ MT Load ability : 12 Tone in 20 ft Container and 26 MT in 40 ft Container Pack Size : 40 Kg in HDPE Bags with Polyliner Inside Shelf Life - 2 Yrs.
The frozen taro will be peeled, cleaned, cut as the buyer requests and frozen. Frozen Taro Haft - Cut is packed in 1kg per bag. They are stored at -18 degrees Celsius. The taro are washed with a vegetable washing machine, then they are transferred to the preliminary processing area. Taro tubers are peeled, remove damaged parts then they are washed with clean water many time. Taro tubers are cut and waiting for freezing. They are frozen at -18 degrees Celsius and freezing time must be ensured so that they freeze completely. Frozen Taro is packed in 1Kg bag, then 10kgs/carton box
----VIETNAM COCO PEAT MOSS--- Coconut peat is a multi-purpose development medium made from coconut husks. Coir shells are pre-washed, machine dried, sifted and free from sand and other contaminants such as animal and plant residues. Coconut peat is a very good alternative to traditional peat moss. The air is filled with porosity and high water holding capacity, making it an ideal growth medium for plants. It is 100% organic and environmentally friendly, free of pathogens and weeds. It has a pH of 5.8 - 6.8, EC level
TECHNICAL DATASHEET EcoTexTM -SL55 - PVA FREE ONE-SHOT PRODUCT DESCRIPTION Powder types unique one-shot product which needs no extra native starch, modified starch, binder, softener, lubricant to be added further. It is mainly used for Shuttle-less loom woven warp yarns counting above the 40s to 60�¢??s Cotton. Products are made from grafted starch, anionic polymers, and synthetic fatty matters. It contains a maximum of 13% moisture and an optimized viscosity level. Easily disperse in cold water with little swelling property due to high binding property. SPECIFICATIONS 1.Appearance - Off white powder 2.pH value of 7% solution - 5 to 7 3.Solubility - Partially soluble in cold water 4.Viscosity of size mix - 4 to 5 sec (SITRA -6mm cup) 5.Total Moisture - Max 13% 6.Bulk density - 0.5 to 0.6 g/ml 7.Total ash - Max4% COOKING METHOD 1. Fill the required quantity of water in a cooker 2. Gradually add EcoTexTM-SL55 and min for 2 min. 3. Close the pressure cooker lid. 4. Open the steam value and cook to @ 120�? �ºC or 35psi. 5. Retain in the cooker for 15 to 20 minutes. 6. Then transfer the size mix to storage. PROPERTIES 1. Moisture regain: The formation of thin flexible film absorbs water molecules from atmospheric air that maintains the required moisture content of the sized yarn. This property improves the weaving efficiency by reducing the warp stops. 2. Film property: The very thin strong film gives the inter fiber penetration that improves yarn tensile strength. Optimum elongation and flexible property significantly reduce warp break by overcoming the applied tension during weaving. 3. Abrasion resistance: The strong film withstands the mechanical friction between yarn to yarn and yarn to machine parts like reed, dropper pin, heald wire, weft picking element. DE-SIZING Easily de-sizable product with hot alkali treatment. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY Stable for one year from the date of manufacture. PACKING Available in 25Kg net weight PP bags with moisture-proof liner inside
EcoTexTM-SL20 - PVA FREE ONE-SHOT PRODUCT DESCRIPTION New generation eco-friendly one-shot product for a high-speed shuttleless loom. It is mainly used for 6 to 203 cotton yarns sizing. This product is entirely biodegradable and ecological. Products are made from grafted starch, anionic polymers, and synthetic fatty matters. It contains a maximum of 13% moisture and an optimized viscosity level. Easily disperse in cold water with little swelling property due to high binding property. Having high penetration power and plasticizing power for heavy construction fabrics weaving. SPECIFICATIONS 1.Appearance - Off white powder 2.pH value of 5% solution - 6 to 8 3.Solubility - Partially soluble in cold water 4.Viscosity of size mix - 5 to 6 sec (SITRA -6mm cup) 5.Total Moisture - Max 13% 6.Bulk density - 0.5 to 0.6 g/ml 7.Total ash - Max4% COOKING METHOD 1. Fill the required quantity of water in the cooker. 2. Gradually add EcoTexTM-SL20 and mix for 2 min. 3. Add other ingredients and mix for 2 min. 4. Close the pressure cooker lid. 5. Open the steam value and cook to @ 120�? �ºC or 35psi. 6. Retain in the cooker for 15 to 20 minutes. 7. Then transfer the size mix to storage. PROPERTIES 1. Moisture regain: The formation of thin flexible film absorbs water molecules from atmospheric air that maintains the required moisture content of the sized yarn. This property improves the weaving efficiency by reducing the warp stops. 2. Film property: The very thin strong film gives the inter fibre penetration that improves yarn tensile strength. Optimum elongation and flexible property significantly reduce warp break by overcoming the applied tension during weaving. 3. Abrasion resistance: A strong film withstands the mechanical friction between yarn to yarn and yarn to machine parts like reed, dropper pin, heald wire, and weft picking element. DE-SIZING Easily de-sizable product with hot alkali treatment. STORAGE Keep away from direct sunlight and store in a cool, dry, and well-ventilated place. STABILITY Stable for one year from the date of manufacture. PACKING Available in 50Kg net weight PP bags with moisture-proof liner inside.
Starch production line machine small capacity to big capacity design ,manufacture,installation,training for clients. Cassava,potato,sweet potato,corn,wheaten and so on can produce starch. Cassava starch production line process flowing : cassava feeding----first time drying washing (removing impurities)----second time water washing(remove small impurities----cassava crush----sieve off cassava residue ----starch milk purification----dewater drying----screening packaging .Whole process are sealing process no-touch hand keep sanitary ,good quality starch .The starch are wildly use for raw materials such as food ,medical and cosmetics ,textiles,papermaking ,candy, beverages, animal feed, biodegradable materials, adhesives , chemicals, ethanol /alcohol , etc.
Materials: carbon steel and stainless steel (302,304,304L,316,316L etc). Characteristics:The welded stainless steel water well screen is made up of rods and warp. The rod can be round wire, triangular wire or trapezoid wire. The warp is triangular wire (V-shaped wire). Water well screens have a structure and high open area, as well as accurate slot dimension. At the same time, water well screen have heat-resisting, anti-corrosive, good machine capability, last long, safety and reliability and so on characteristics. It can be used in many kinds of medium filtering. Uses: The strainer is a kind of filtered water tubing with the perforation .it can use with the deep well pump, dive the water pump, also may use in the water-treating equipment, the environmental protection, the sea water transforms into the industrial water and life use water desalination treatment, running water treatment, water softening treatment, the petroleum industry: The petroleum product terminal filters and the chemical acid, the alkali liquid filters, the ethyl alcohol and so on the organic solution recycling filters. Continuous slots significantly increase discharge area,thus providing greater access to water-bearing zone . We can produce this pipe with diameter 80mm-550mm ,slot size 0.1mm-10mm,length 50mm-5850mm .
HIPS Regrind from post consumer materials Thermoplastic PS has two representatives as GPPS and HIPS resin. In particular, PS HIPS plastic is more popular thanks to many advantages and applications. PS HIPS belongs to the group of hard, transparent resins that are easy to color, machined by suction lamination method and easy injection technology. Common HIPS applications: In packaging technology, it is used as a single-layer packaging for products that do not require strict antioxidant requirements. Make coating HIPS plastic film to increase water vapor and gas resistance. Making a printing surface to increase printing ability, making the outer plastic packaging with the ability to tear easily and create gloss. Making bottle caps, pen cases, jewelry boxes, beer tanks, fresh food containers. Making pharmaceutical bottles, pipes, cap for solvent containers. Making high-frequency insulating materials, insulation clamps. Making imitation leather sandals, textile packaging. Pressing students' tables and chairs, pressed motorcycle details, yogurt cup, plastic candy tray. MATERIAL: HIPS Regrind from post consumer materials ,Yes No Fr, NO pc abs, no iron, no circuit etc CATEGORY: HIPS TYPE: Regrind SPECIFICATION: Hips from post consumer materials.Yes No Fr, NO pc abs, no iron, no circuit etc. Hips per month 52 mt Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days