Waste tyre to oil recycling process pyrolysis plant the obtain thing as follows: 45%-55% fuel oil, 10%-15% steel wire, 30%-35% carbon black and 8%-10% flammable gas. You can get diesel from fuel oil by distillation plant.www(dot)wastetireoil(dot)com You can get a very high profit by disposing these wastes, and also it's helpful for improving the local environment, avoid garbage pollution. Waste tyre to oil recycling process pyrolysis plant advantages: 1. One week installation:no need to build foundation thus shorten the construction period, 4th and 5th machine installation period is one month, 6th machine install only need one week. Also easy to move. 2. Service life: Special design inside the reactor to avoid direct www(dot)wastetireoil(dot)com heating, so machine service life prolong to 3-5 times and the heating energy can realize 100% utilization. 3. De-dusting system: "Four in one" de-dusting system can reach European standard, 100% environmental friendly.also no need building the water pool, saving cement, brick cost, saving time. 4. Cooling system: A. 36 meters cooling condenser pipe, inner each pipe have 4 small pipe, cooling performance is very good. B. "Four in one" condensing systems. Waste tyre to oil recycling process pyrolysis plant final product application Fuel oil 1. As the fuel material used in Cement factory, glass factory, ceramic factory, electric power factory, steel making factory, boiler factory, etc. 2. Final diesel come out from our distillation plant and deodorant & decolorant can be used in diesel generator. 3. Used in diesel powered cars, such as vans, truck, tractor, etc. 4. Use as heating oil, industrial and home. Carbon black :www(dot)wastetireoil(dot)com 1. Make it to briquette for fuel. 2. Used in rubber and painting factory after carbon black grinding to 200-4000 mesh. Steel wire:Sell to iron and steel factory (you can take out steel wire from tyre before pyrolysis) Waste gas: 1. Recycled into furnace heating reactor instead of coal/wood/oil/natural gas. 2. Storage the exceed gas to restart the next batch.
Dy-6t capacity waste plastic pyrolysis to oil plant (d2200mm*l6000mm) 1. This mode of waste plastic pyrolysis to oil plant can load 6 tons of plastic. 2. After finishing one batch, with auto-feeder, you don't need to wait the pyrolysis machine cooling down since workers will have to go inside to feed material. If you don't have one, in that way it will be time-wasting and dangerous. 3. Built-in spiral plates, these plates will make the waste plastic go ahead. Dy-8t capacity waste plastic pyrolysis to oil plant (d2200mm*l6600mm) 1. It can load 8 tons of waste plastic. 2. The reactor adopts q245r steel plant and its thickness is 16 mm, which can bear 500-750 batches. 3. We can also make reactor by material q245r, which obviously prolong service life 3-5 times. 4. The reactor has two layers, the outer layer built-in cotton insulation, fire cement and steel. Dy-10t capacity waste plastic pyrolysis to oil plant (d2600mm*l6600mm) 1. Working with auto-feeder, it is able to contain 10 tons or 12tons waste plastic. 2. The diameter of feeding port is 1200mm or 1400mm. After 2 hours feeding time, it's time to heat the reactor by coal/wood/natural gas/crude oil. Generally speaking, when the temperature ups to 155 celsius degrees around, the oil gas will generate. Waste plastic working time you may need: Let’s take 10 tons waste plastic that processed by doing waste plastic pyrolysis to oil plant as an example: Model Feeding Processing Cooling Discharge Total 2200*6000 1.5hr 7-8hr 1.5hr 1.5hr 12hr 2200*6600 1.5hr 8hr 1.5-2hr 1.5hr 14hr 2600*6600 2 hr 10 hr 2-3 hr 2-3 hr 16-18 hr Waste plastic pyrolysis to oil plant is a very good investment, not only can efficiently deal with a large number of abandoned tyres, turn waste into treasure, but also can avoid environmental pollution caused by landfill or burning these waste.
Waste plastic pyrolysis to oil plant working process: Feed waste plastic into the reactor with auto-feeder, seal the reactor gate and begin to heat the reactor by burning fuel materials in the combustion system, the fuel material can be coal, wood, natural gas and fuel oil. There is a thermocouple installed at the oil gas outlet valve to test the temperature of the oil gas, when thermocouple shows a certain temperature, the oil gas will come out and flow into the cooling system and be converted into liquid oil. At the same time, the oil gas conations CH4, C2H6, C3H8, C4H10 and H2 which cannot be cooled under normal pressure will be recycled back to combustion system to burn as fuel material. The dust and sulfur gas will be removed by the dust removing system. After the gas oil run out, there are slags (carbon black) inside of the reactor,. As a plastic pyrolysis machine manufacturer-DOING will provide customer a good quality machine with adopt fully automatic vacuum carbon black discharging system that extend the service time. Choosing the suitable raw material is important for customers, it concerns the real profit you can get from your material. Not all kinds of waste plastic can get oil, if you want to get crude fuel oil with high oil yield from waste plastic, please refer to the following form: Here I need to stress that the oil rate only for your reference, as different plastic different result, such as some plastic has very dirty slag, and the plastic is very wet. Let’s see it: Oil rate from different kinds of plastic: This project widely used by all over the world, such as recycling center, waste plastic recycling organization, collecting company etc. Waste plastic pyrolysis oil plant has the advantage of small investment and quick recovery costs, is a very good project in the next 5-10 years. If you want to know more information about details, please contact with us.
Waste tyre pyrolysis plant cost How to convert waste tyres to useful resources Now, it is no longer a problem. With 18 years' experience in the field of tyre pyrolysis, and continuous research, development and improvement, Doing group provides the latest waste tyre pyrolysis plant which has reached a high level in technology. The Waste tyre pyrolysis plant adopts the new green pyrolysis technology. Through the use of the tire pyrolysis oil plant, waste tyres can be effectively converted to fuel oil, carbon black and steel wire. The oil from tyres plant can be widely used as fuel oil in industries such as steel and iron and boiler factories, ceramics, power or chemical industries etc. And it can be used for generators to get electricity. Carbon black can be used for making construction bricks with clay, and also can be used as fuel. Steel wire can be recycled into smelting plant. The tyre pyrolysis oil market price is quite high in the market, which will surely get you tyre pyrolysis plant cost back soon as well as help relieving energy crisis.
Doing group continuous waste plastic pyrolysis plant can process 30-50 tons of waste plastics (such as PE, PP, PS, ABS, pure white plastic, pure plastic cable, pure purchase bag etc.)per day, which can work continuously for 24 hours without a stop. In a word, the latest continuous waste plastic pyrolysis plant has the features of small size, small floor area, simple operation, less operator etc. To a large extent, the new device not only saves the operating costs, but also improves the work efficiency.www(dot)doinggroup(dot)com Continuous waste plastic pyrolysis plant is mainly composed of moving horizontal pyrolysis reactor, hot air circulation heating system, oil gas filter, spray cooling system, secondary fire retardant damper, strong spray de-dusting system, oil gas recycling system, feeder system, discharging system, pressure and temperature multipoint monitoring system, central electric control system. All of parts are manufactured with high-quality materials and advanced technologies, so the quality of this plant can be guaranteed.www(dot)doinggroup(dot)com The latest continuous waste plastic pyrolysis plant adopts the screw feeding sealing system technology, which is hold by the companyâ??s invention patents, hot air heating furnace circulating heating technology, heat drying technology with high heat exchange efficiency and capacity. Impeccable electrical control system save labor costs. Three waste utilization reasonable recovery can basically realize of zero emissions, safety and environmental protection. z
More than 250 million scrap tires are generated annually in the United States and their proper management continues to be a solid waste management concern. Sound markets for scrap tires are growing and are consuming an ever increasing percentage of annual generation, with market capacity reaching more than 75 % of annual generation in 1996. Of the three major markets - fuel, civil engineering applications, and ground rubber markets - the use of tires as a fuel is by far the largest market. The major fuel users include cement kilns, pulp and paper mills, electrical generation facilities, and some industrial facilities. www(dot)wastetireoil(dot)com Scrap tires are an ubiquitous by-product of contemporary social and economic society. Our personal mobility is almost entirely dependent on the pneumatic tire, whether in automobiles, buses or even airplanes. The transport and delivery of most goods is also dependent on the pneumatic tire. To recall an old slogan of the American Trucking Association, "If you got it, a truck brought it", and it goes without saying that the truck was riding on pneumatic tires. The tire derived fuel recycling pyrolysis plant can effectively convert waste tire into fuels, like Oil, Carbon Black, and Hydrocarbon Gas etc. Here, the raw material is either waste tire or waste plastic. Then, the recycleables are heated from the reactor to be able to generate fuels, oil, and gas.www(dot)wastetireoil(dot)com 1.Using tire derived fuel recycling pyrolysis plant available for sale, stick to experience an excellent, eco-friendly & cost-effective solution for tyre recycling.www(dot)wastetireoil(dot)com 2.On an average, the entire pyrolysis process may lead to a yield of around 45-52% oil, 30-35% charcoal, and 15% gas. The oil produced is mainly made up of diesel, kerosene, benzene, fuel oil & heavy fuel oil. Hence, the produced oil may be further refined and useful for operating any vehicle.www(dot)wastetireoil(dot)com 3.The plant pollution has truly get to be the most problem nowadays. Obviously, scrap tire derived fuel pyrolysis plant give you a meaningful strategy to it while promoting an eco-friendly solution by reduction of the hazards of land pollution due to the waste tire.
Scrap Tires are an ubiquitous by-product of contemporary social and economic society. Our personal mobility is almost entirely dependent on the pneumatic tire, whether in automobiles, buses or even airplanes. The transport and delivery of most goods is also dependent on the pneumatic tire. To recall an old slogan of the American Trucking Association, "If you got it, a truck brought it", and it goes without saying that the truck was riding on pneumatic tires. The Scrap tire derived fuel pyrolysis plant can effectively convert waste tire into fuels, like Oil, Carbon Black, and Hydrocarbon Gas etc. Here, the raw material is either waste tire or waste plastic. Then, the recycleables are heated from the reactor to be able to generate fuels, oil, and gas. 1.Using Scrap tire derived fuel pyrolysis plant available for sale, stick to experience an excellent, eco-friendly & cost-effective solution for tyre recycling. 2.On an average, the entire pyrolysis process may lead to a yield of around 45-52% oil, 30-35% charcoal, and 15% gas. The oil produced is mainly made up of diesel, kerosene, benzene, fuel oil & heavy fuel oil. Hence, the produced oil may be further refined and useful for operating any vehicle. 3.The pyrolysis plant pollution has truly get to be the most problem nowadays. Obviously, scrap tire derived fuel pyrolysis plant give you a meaningful strategy to it while promoting an eco-friendly solution by reduction of the hazards of land pollution due to the waste tire. 4.By converting the waste into energy, Scrap tire derived fuel pyrolysis plant offers an alternative energy source too. Scrap tire derived fuel pyrolysis plant falls beneath the following kinds of industrial projects 1.Waste to energy project 2.Renewable energy project 3.Waste tire and plastic control equipment 4.Petrochemical Fuel Oil The fuel oil is between 45 and 52 percent. This fuel oil does apply in power plant factory, ceramic factory, aluminum factory, glass factory, painting factory, boiler system factory and boiler factory. The proportion found as soon as the recycling is 30 to 35 percent of carbon black. This device works extremely well within the electric cable jacketing, doormat and hose mat, conveyor ban, rubber addictive, automatic spare parts, heat isolation plus more.
Pyrolysis is a thermochemical decomposition of orgnic material at elevated temperatures in the absence of oxygen. Pyrolysis typically occurs under pressure and at the operating temperatures at 430?. Pyrolysis is a special case of thermolysis, and is the most commonly used for organic materials, being, therefore, one of the processed involved in charring. In general, pyrolysis os organic substances produces gas and liquid products and leaves a solid residue richer in carbon content. Extreme pyrolysis, which leaves mostly carbon as the residue, is called carbonization. The process is used heavily in the chemical industry, for example, to produce charcoal, activated carbon, methanol, and other chemicals from wood, to convert ethylene dichloride into vinyl chloride to make PVC, to produce coke from coal, to convert biomass into syngas, to turn waste into safely disposable substances, and for transforming medium-weight hydrocarbons from oil into lighter ones like diesel or gasoline. All these specialized used of pyrolysis may be called various names, such as dry distillation, destructive distillation, or cracking, but all same principle. For us, we mainly specialized in manufacturing and supplying waste tire/plastic/rubber pyrolysis plant, mostly for processing the rubber products to get fuel oil. On one hand, with the modernization of the society, rubber industry develops at a rapid speed, rubber manufactures are widely used in many field of life. On the other hand, the pollution of scrap rubber or plastics is increasing for its difficulty in disposing safely, which is also called “Black Contamination”, has become a big threat to the environment and is getting increasingly serious. Sale fully automatic continuous tyre pyrolysis plant In the early years, the most commonly used pyrolysis plant is mainly the batch operation process, which has low investment but complicated operation process and high labour cost. With the technology improving and customers’ requests, we DOING Company developed a new technology continuous pyrolysis plant. This continuous pyrolysis plant has fully automatic process, which can be controlled by PLC system or computer, thus to save the labour cost. And with the automatic and continuous feeding and discharge system, it can make the the pyrolysis system keep running 24/7 without stop, thus to save the valuable time and energy which are consumed in the batch manual operation system.
Pyrolysis is a thermochemical decomposition of organic material at temperatures between 400 ° C and 900 ° C without the presence of oxygen or other reagents . The pyrolytic breakdown of wood produces a large number of chemical substances . Some of these chemicals can be used as substitutes for conventional fuels . The distribution of the products varies with the chemical composition of the biomass and the operating conditions. Pyrolysis Plant include 45-52% tire oil, 35% carbon black; 12-15% steel wire; 5-8%. Tire oil is also called fuel oil, can be directly sold (they are also used for processing or used for boiler combustion, bath center, restaurants, burning fuels such as floor brick) or deep processing into organic solvent with refining equipment and automotive fuel, etc.
This small tyre doubling machine is ideal for any workshop or used tire dealer, used to double or undouble (unpack tires). It is powered by compressed air only so there is no risk of electrocution. We recommend this doubling machine for small workshops wishing to save space for storing or transport their scrap or part worn tyres. Due to its small dimensions and weight it is ideal for moving from one place to the other. For some tyre pyrolysis factories, they want to fill as many tires as possible inside the reactor for pyrolysis to oil. But as we all know that tires contain steel wire which is difficult to press. This time you will need to use a tire cutter to cut tyres into small pieces. But after cutting, the steel wire inside tires will become small pieces mix with carbon black after pyrolysis process, which is difficult to separate. For tire packing machine, you can use it to make several complete tires together, then put them into the reactor. It can not only save the plave, the steel wire inside tires also can keep complete. After pyrolysis, the big steel wire can tangling together, which is easy to pull out by a hook.
