Application and Brief Intro
HST-01 Heat Seal Tester is for the determination of the heatsealability of a surface, or sealant layer of films, laminates, composites and polymers etc. How well the material heatseals is expressed quantitatively as seal strength as a function of the sealing conditions of temperature, time and pressure. HST-01 Heat Seal Tester is professionally designed for the precise measurement of the three parameters of temperature, time and pressure in the heat seal process. HST-01 Heatsealability Tester conforms to standards of ASTM F2029, QB/T 2358 and YBB 00122003.
Principle
Place a sample between two-heated sealing jaws of HST-01 Heat Seal Tester with flat surfaces when the required temperature reaches equilibrium. The upper seal jaw, driven by a gas cylinder, is pushed down, to exert a certain pressure on the sample and remain for some time. When the preset sealing time ends, the upper sealing jaw returns to its original position and the whole heatsealability testing process finishes.
Brief introduction:
Lt-01 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-01 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-01 leakage tester complies with astm d3078 and gb/t 15171 standards.
The leak detection system is composed of the mainframe and the vacuum chamber. A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated.
Features
Lt-01 leak tester uses vacuum ejector to generate stable vacuum environment. .
The leak detection requires no electricity
High leakage test efficiency
Extra-thick perspex
Different chamber sizes available
No calibration needed
No vacuum pump required
Easy installation, start-up and operation
Low maintenance
Brief introduction:
Lt-02 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-02 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-03 leakage tester complies with astm d3078 and gb/t 15171 standards.
The leak detection system is composed of the mainframe and the vacuum chamber.
A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated.
Features
Brief introduction:
Lt-03 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-03 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-03 leakage tester complies with astm d3078 and gb/t 15171 standards.
The leak detection system is composed of the mainframe and the vacuum chamber. A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated.
Features
Lt-03 leak tester uses vacuum ejector to generate stable vacuum environment. The state-of-the-art human-computer interface and plc control unit on the leakage detection system make the parameter setting and test operation direct and easy. By saving different groups of parameters, users are free from the troubles of setting parameters each time before use. At the same time, different testing results and total test numbers can be saved to avoid any human errors.
1. Leak test process all automatic
2. Touching screen operation
3. Digital vacuum degree and test time input
4. Parameters and test data automatic saving
5. Automatic vacuum maintenance and air back-flushing
6. Extra-thick perspex
7. Different chamber sizes available
8. No vacuum pump required
9. Easy operation and maintenance
Application and Brief Intro
LSST-01 Leak and Seal Strength Tester is suitable for the quantitative determination of sealing strength, heating sealing quality, burst pressure and leakage of flexible and aseptic packages. The Leak and Seal Strength Detector can also be used to determine the sealing performance of pilfer-free bottle caps and soft tubes. The compression strength, connection strength of cap and body, cap losing strength, seal strength and butting strength of tubes are the applications of LSST-01 Seal Strength Testing System.
This Seal Strength Testing System conforms to standards of ISO 11607-1, ISO 11607-2, ASTM F1140, ASTM F2054, GB/T 10440, GB 18454, GB 19741, GB 17447, GB/T 17876, GB/T 10004, BB/T 0025, QB/T 1871, YBB 00252005, YBB 00162002 .
Principle
The three test modes of the positive pressure method, which LSST-01 Leak and Seal Strength Tester satisfies are as follows:
A. Burst Test: LSST-01 Leak and Seal Strength Tester internally pressurizes the packages until the package fails. The test pressure is the maximum pressure detected before the package fails.
B. Creep Test: Pressurize the package internally to a specific pressure and maintains this pressure for a specific time. The test measure is pass/fail.
C. Creep to Failure: The package is creep-tested and held until the package fails. The pressure setting is higher than that of the creep test to ensure the package fails in some time. The measure is the time until failure.
food packaging bag hermetic sealing quality test Leakage tester
GB-M Leakage Tester
Application
To test the hermetic sealing quality and performance of packaging bags, bottles, cans and so on, used in industries of food, beverage, pharmaceuticals, personal care and so on.
Standard
ASTM D3078
Item
Technical Parameters
Vacuum degree
0 -80kPa
Vacuum precision
1%
Vacuum keeping time
0.1 99.99h
Sample size
300 350 mm
Intake pressure
0.7 0.8 Mpa
Consumption of compressed air
20 L/min
Power supply
220 V 50 Hz
Instrument size
Net weight
20kg
Power
100W
Ambient temperature
JHG design shelf glass with different style , functionality, durability ,and affordability ,to meet all clients inquiry . Glass shelves is necessary accent for the kitchen, bedroom, bathroom, furniture and home appliance in our life.
All shelves including :
Clear and white satin colors
Polished and bevelled edges glass shelves
Rectangular ,shape size and curved glass shelves
Coloured glass with back painted
Any sizes available
Package :
Wooden cases
Carton with indicated logo
Thermal plastic sealed package
JHG fire-resistant glass is combined with borosilicate glass and float glass technology, which fire resistant properties much superior to those of sode lime glass , the main character is :
* high performance to bear high temperature , our tempered borosilicate glass 4.0 can withstand 120 minutes fire test .
* Ultra light ,borostilicate glass 8% less than sode lime glass
* Hign soften point in fire
* High ligh transmission
* No SO2 pollution ,no self-explosion
Borosilicate 4.0 Technical data :
Size: 1830*3000mm
Density (g/cm�?�³) : 2.28�?�±0.1
Co-efficient of expansion (�?�±)(20-300�¢??) : 4.0�?�±0.1�??10-6k-1
Softening point(�¢??) : 845�?�±10
Light transmission :�?� �¢?�¥90(6mm)
Main usage :
4.0 building partition ,facade ,door ,ceiling ,floor
3.3 household application ,optics , lighting
