Waste Plastic Suppliers and Manufacturers

We can produce and sell biomass gasifier, such as city waste plastic gasifier, garbage gasifier, MSW gasifier Gasifier PRODUCT FEATURE 1. The gasifier uses fixed bed down-draft type, produce syn-gas continuous and stably with low tar content, it can generate electricity continuous. 2. Easy to use and operate, use Siemens PLC touch screen control panel to realize automatic control and semi-automatic control. Independent operation room, adjust parameter directly by controlling LCD touch screen. Then gen set will operate with separately control system. 3. Due to MSW gasification process adopts pyrolysis and accurate control in different stage, so it can reach specified flue gas standard. 4. Due to low temperature gasification combustion(gasifier furnace) under anaerobic condition and low temperature gasifier and combustion, only producing combustible gas, particulate matter emission is precious little. 5. Finish low temperature oxidation process in high temperature combustion cha ber (combustion furnace), not producing harmful gas secondary pollution. 6. Due to combustion process is complete, the ash is completely non- pollution matter. 7. The removal rate of organic is over 90%, so it reduce the follow-up treatment cost greatly. 8. All kinds of waste with different composition can burn stably at the same time. 9. Safety separation combustion, restrict dioxin and other harmful matter output. 10. Operation 24 hours/day continuous. 11. Waste need to sort out, and improved operation efficency, ensure the safety of working environment. 12. Haiqi gasification system is fully closed, it is neat and beautiful look at site, no harmful to operation people. Automatic fuzzy control, easy to operate. All fuel feeding, slag discharge door, overhaul hole use soft seal, On the top of furnace has a seal cover to avoid gas leakage. The sealing of furnace is good, realizing good effect of oxygen controlling and pyrolysis. 13. When pyrolysis gas spontaneous combustion take place, then it enter into a process of spontaneous combustion, auxiliary combustion device will stop automatically. The whole process of spontaneous combustion is over 90%, greatly lower running cost. Realized resource utilization of waste thermal energy. Flue gas emission is no harmful and total CO2 emission is reduced. APPLICATION SCOPE 1. Oil/gas/coal fired boiler, Boiler Industry (steam boiler, thermal oil furnace, hot water boiler) 2. Smelting Industry (aluminum melting furnace, reverberatory furnace) 3. Drying Industry (food drying, sawdust/wood chips/biomass drying) 4. Spray Coating Industry (metal spraying, electroplating heating) 5. Greenhouse, Building Industry (asphalt heating)

Convert waste plastic into fuel oil of Doing oil pyrolysis machine which can turn waste plastic into fuel?www(dot)china-doing(dot)com How to convert waste plastic into fuel oil ? Doing waste plastic into fuel oil pyrolysis machine working process as follows:www(dot)china-doing(dot)com 1. Put raw materials into reactor by auto-feeder, then heat the reactor with any one of the following fuel materials: coal, wood, natural gas, oil. Do not stop heating the reactor, when the temperature reaches nearly 250 degree Celsius, waste tyre will be transferred to oil gas.www(dot)china-doing(dot)com 2. The liquid oil will be cooled by condenser from oil gas and then collected by oil tank. Third, the exhaust gas which can not be cooled in normal pressure will be recycled to heat the reactor. In this way, you can not only saving energy, but also protecting environment. 3. Smoke produced by processing the plastics can achieve national emission standard through dual desulfurization and dusting removal device. 4. After you get oil, the temperature will be low, at this time, carbon black will be discharged automatically.www(dot)china-doing(dot)com Last, when the temperature falls to 100 degree Celsius, After all these steps, you can start another batch.

The pyrolysis of plastics waste is a new green technology to recycle plastic and we Doing group have applied this technology in our plant. By using the plastic to fuel oil pyrolysis plant, finally you can get oil from the plastic waste, and you can also get the carbon black and combustible gas, all of which have a wide range of applications. www(dot)wastetireoil(dot)com According to the demands of different customers, we provide three types of plastic to fuel oil pyrolysis plants for customers, including batch operating plant, semi-automatic operating plant and auto continuously operating plant. Each set of plant is www(dot)wastetireoil(dot)commanufactured with advanced technologies and has the features of high efficiency and low cost. The following are some technologies applied in the plant: 1. The first in the world to have created the new heating structure that combines the advantages of burning the reactor directly and heating the main reactor by hot air. 2. The technology of avoiding the reactor of being burnt through by reforming the furnace, which will lengthen the life span of the main reactor for 5 to 8 years and save quite amount of money for customers to maintain and update the plant. 3. The technology of improving the oil yield by another 5% compared with the traditional plant. 4. The technology of guaranteeing 100% safety in the whole working process. 5. The technology of ensuring the released gas reach the European pollution control standards. z

Waste plastic to oil machine cost can pyrolysis down of waste plastic to energy. Plastic pyrolysis to oil machine is an industry conducted pyrolysis . In the Scrap plastic pyrolysis to oil machine , the long- chain polymers break down into smaller chains of hydrocarbon gases and pyrolysis oils. Heat required for the catalytic reaction .www(dot)wastetireoil(dot)com Every year a large amount of plastic waste is discarded in the Earth. These plastic to with stand the natural process of decomposition of all. According to statistical analysis , Waste plastic generated more than 250 million tons each year. A lot of these plastic garbage is used to fill the land , which in turn may result in a waste land to create a major threat to the environment in the future. People use and dump waste plastics almost every day. Waste plastic to oil Solution: Waste plastic to oil machine cost www(dot)wastetireoil(dot)com Usage: Waste plastic Recycling to Fuel Oil Input: Different plastic type, (PP,PE,PS,ABS) etc. Output: 20%-95% fuel oil, 30%-35% carbon black , 5%-8% gas. Heating material: coal/wood/fuel oil/natural gas Machine cover area: usually 400 square meters. Reactor material: Q245R Boiler plate.

Pyrolysis technology offers a practical solution to recycling of waste plastics by converting it to liquid fuel oil as main product with high marketing values. Plastic types including HDPE, LDPE, PP, PS and others produce high ratio of liquid fuel oil, while PET and PVC doesn t contribute to oil yield. The configuration of main systems of Model C series pyrolysis plant. PYROLYSIS REACTOR: 5/10/15 Tons Of Unit Capacity FEEDING SYSTEM: Hydraulic Feeder CONDENSING SYSTEM: Square Box Condenser HEATING SYSTEM: Oil Burners And Gas Burners EMISSION CONTROL SYSTEM: Water Film Deduster DISCHARGING SYSTEM: U-Shape Screw Conveyor Features of the waste plastic plant: 1. Advanced Choice The condensing system and emission control system of Mode C series provide better performance. Therefore it s more efficient on production and emission control. 2. High Emission control Stainless steel deduster with internal ceramic filters provide better purification of flue gas. It can meet higher environmental standard of more developing and developed countries. 3. Quicker Installation The more integrated design makes installation easier and quicker.

Specification of the 10 ton waste plastic pyrolysis plant: PYROLYSIS REACTOR: 5/10/15 Tons Of Unit Capacity FEEDING SYSTEM: Hydraulic Feeder CONDENSING SYSTEM: Horizontal Condensers HEATING SYSTEM: Oil Burners And Gas Burners EMISSION CONTROL SYSTEM: Water Film Deduster DISCHARGING SYSTEM: U-Shape Screw Conveyor Features of the 10 ton waste plastic pyrolysis plant: Basic Choice to Start Model A series are the basic choices to start pyrolysis business of massive production capacity. Medium Emission Control Water film deduster is suitable for developing countries. It provides basic purification of flue gas. The air emission has no black smoke or bad smell. Onsite Installation The parts need to be assembed on site. Our engineer would travel to the customer's site for installation and training service.

Waste plastics pyrolysis plant refining equipment is now very common. Common, but with the social progress, economic development, the energy crisis has become more and more serious trends. The fuel oil cracked by the refinery equipment can also alleviate the energy crisis to some extent. In order to expand the use of the oil developed by the refinery equipment, DoingGroup has developed a recycling waste plastic pyrolysis plant oil to diesel oil equipment. It mainly uses high-temperature distillation and condensation to refine the fuel oil to obtain a clean and transparent non-standard diesel fuel. The main working flow of the recycling waste plastic pyrolysis plant oil to diesel oil equipment is as follows: 1. Pour the thermal oil into the heat transfer system and heat the base of the heat transfer system. The reactor is preheated. 2. The base of the reactor is heated and the fuel oil is distilled at a high temperature. The residue in the heavy oil can be separated and the light oil and gas will go to the next procedure. 3. Light oil and gas are liquefied through the condensing system and flow into the tank. 4. The light oil collected in the oil tank is degreased and desulfurized to obtain the final clean and transparent non-standard diesel oil. So where does the final revenue from running our recycling waste plastic pyrolysis plant oil to diesel oil equipment come from? The main products of the recycling waste plastic pyrolysis plant oil to diesel oil are non-standard diesel and carbon black. Their specific uses are as follows: 1. Non-standard diesel: mainly used for heavy machinery, generators, boilers. 2. Asphalt: Mainly used for paving and asphalt plant refining. The main advantages of DoingGroup's recycling waste plastic pyrolysis plant oil to diesel oil equipment are as follows: 1. The vertical reactor is easier to discharge than the horizontal reactor. 2. Double heating system, both base heating, heat conduction system, heating fast, short heating time, improve equipment operating efficiency. 3. The reactor can be customized according to the processing volume. One reactor has a capacity of 5 tons. If a capacity of 10 tons is required, two reactors can be customized, and so on.

Waste EPS foam has pollution on the environment if not recycled as soon as possible. But now with the help of an EPS beads shredder, waste EPS foam could be smashed into granules. The waste EPS scraps and waste EPS foam could be reused once combined with EPS raw material. That is, waste EPS foam could be used by the producer according to definite proportions after processing.

Baled pet bottles, 90/10 and 80/20, mixed colores. 16/17mt per container 40hc

Pet bottles flakes, hot washed, pvc less than 300ppm, moisture is less than 2%. Clear color, light blue and green colors. Not mixed others plastics and colors. Big bags

Polymer resins off grade, cotton waste & plastic scrap, Plastic products.

Ground film from greenhouse. Weight per container: ca.(18-22)mt, packed in bales.

Main configuration characteristics This kind of model adopts two-row fixed blade design, with powerful comminuting capability and is specially designed for larger chassis with big pulverizing room, such as TV shell, computer shell, etc. The category of crushed materials: the process of material changing and material cleaning is simple and efficient. The work efficiency and output is improved as the result of stable running and low noise. Our advantage A:Where is our factory? We are in Zisheng street,Gaokeya Garden,Licheng District,Quanzhou City,Fujian Province. B:How to get to our factory? (1)You can get to the Jinjiang airport directly,then,connecting us and we will pick you up by car (2)You can take the train to Quanzhou station,then,we will pick you up by car C:Why choose us? (1)We have complete system of designing of our equipment (2)We can provide the perfect management solutions  (3)We could make you in a leading position in the industry D:What's the payment method? L/C,T/T,Western union E:Can we see the running machine in ur factory? Yes.Before making your decision buying the equipment or not,you can bring some material here to test-run the equipment F:How long of the warranty time? Our warranty period is 1 year

1.Working process: Firstly , put the raw material into furnace, then seal the feed inlet system. Secondly, burned the fuel material(coal, or wood, or natural gas , oil ) in the combustion system, the reactor will slowly heat , when the temperature reaches around 250 degree celsius, it will produce oil gas, oil gas will be processed by our technology , then go to cooling system to cold liquid oil. The gas which can not be liquid under normal pressure , which will be designed to back to combustion system to instead the fuel material to burn the reactor, which can save energy very much . After finishing oil produce , the temperature of reactor will be down, At the same time , carbon black will be discharged automatically. Lastly, when the temperature falls to 100 degree celsius, worker could open the door of reactor to discharge of steel wire . Then can start another batch working. 2.The usage of final production-----fuel oil Fuel oil from waste tyre are used in below industries A.Power plant factory B.Glass factory C.Cement factory D.Ceramic factory E.Aluminum factory F.Boiler factory G.Central heating factory H.Painting factory The usage of final production-----carbon black Carbon black from waste tyre are used in below industries A.Electric cable jacketing B.Conveyor ban C.Hose and doormat D.Black nylon bag E.Rubber additive F.Automatic spare parts G.Heat isolation H.Black colorant in rubber materials I.Plastic pipes J.Industries rubber products K.Fire fighting The usage of final production----- steel wire Steel wire from waste tyre can be re-sale to steel factory. It varies according to diffrent capacity.

The advantages of our rotomolding: 1) Economic tooling costs. 2) One-piece construction. 3) Weight reduction-as compared to most metals. 4) Uniform wall thickness-nothing in the extremites. 5) Thickness can be varied if required 6) Variety of finishes and color. 7) The ability to produce multi-wall moldings. 8) Design flexibility-from small and intricate to large and complex. 9) Metal inserts as integral parts. 10) Short lead-time. 11) Resistance to stress-cracking and corrosion. International standard

We would like to introduce our company Habricus Group as group of companies. We are working since 2005 in the field of manufacturing of Pre Engineered Buildings, Industrial Machines and trading of furniture. We also exports all our products worldwide. We manufacture Pre Engineered Buildings & Industrial machines Like Lathe Machines, All Geared Lathe Machines, Heavy Duty Lathe Machines, Vertical Turning Lathe, Heavy Duty Rail Planer, Heavy Duty Plano Miller, Shaper Machine, Mechanical Plate Bending Machine, Press Brake Machine, Hydraulic Shearing Machines, Mechanical Over Crank Shearing Machine, Cylindrical Grinder, Center less Grinder, Surface Grinder, Power Press (C-Type / H-Type), Hydraulic Press, Heavy Duty Saw Machine, Slotting Machine, Pillar Type Drill Machine, Hydraulic Drill Machine, Horizontal Hydraulic Operated Milling Machine, Vertical Hydraulic Operated Milling Machine, All Geared Vertical Universal Milling Machine and All Geared Universal Milling Machine. We also manufacture CNC Machines Like CNC Double Column VMC (Vertical Machining Center), CNC Vertical Machining Center(VMC), CNC Vertical Turning Lathe (VTL), CNC Turning Center, CNC Gang Tool/Linear Tool Turning Center, CNC Drill Machine and CNC Vertical Turrret RAM Type Milling Machine. Since 2005, Habricus Group is Located in Industrial city Ludhiana in the state of Punjab, which is the important industrial city in India. We are in possession of a group of highly competent technical person, a market-oriented experienced sales team. In the gesture of sincere cooperation, we strive to establish a promise-keeping and quality guaranteeing sales and after service system in order to offer client perfect pre-sales consultation and after - sales service promptly. We have complete quality guarantee system, prompt goods supply as well as perfect after-sales service. We ensure Habricus Group to be your first consideration when purchasing high-precision machines and machine tools. Customer's satisfaction is our motivation for progress and self-improvement. We sincerely to be your best cooperation partner. Our company have CE, ISO:9001, ISO:9002 international certification.

100% new raw material; Five colors:yellow, grey, green, blue, red

Pengky Plastic Hand Serok Deluxe A plastic bag made of plastic, which is produced in 2 sizes, small and large, to transport garbage in your environment.