Technical Specification Chart: Parameter 1 - Phase 2 - Phase 3 - Phase Unbalanced Air Cooled 3 - Phase Balanced Oil Cooled 3 - Phase Unbalanced Oil Cooled Energy Conserved Lighting Load Centralized Stabilizer for offices & residence Rating (KVA) 1 - 20 0.5 - 20 3 - 100 3 - 200 3 - 250 3 - 500 3 - 500 I/P Voltage range (V) 170 - 270 195 - 265 340 - 480 240 - 480 340 - 480 360 - 460 310 - 480 340 - 460 360 - 460 340 - 480 360 - 460 310 - 480 340 - 480 360 - 460 310 - 480 340 - 480 360 - 460 O/P Voltage (normal) 230 V 415 V 415 V 415 V 415 V 208 V LN 220 V / 230 V LN Alternate O/P setting 220 V / 240 V 380 V / 400 LL 220 V LN 220 V / 230 V LN O/P V regulation ± 1% of nominal output voltage O/P V Indications Digital voltmeter, accuracy 1% of FS ± 1 digit LED Indications Front panel LED Indicators, Input ON, output ON, Input high / Low, output High / Low trip Under over voltage trip Electronic cutoff circuit with graded time delay set @ + 5% / -10% of nominal voltage Over Load cut off Electronic cutoff circuit with graded time delay set @ 110% of rated full load current Short circuit protection HRC fuse / MCB at input Single phasing prevention Not applicable Provide Individual phase cutoff only Service bypass Not provided Provide upto 100 Kva. 3 phase Individual phase bypass provided up to 50 kVA 3-ph Resetting mode Automatic restart with time delay mode of 15 sec. (optional).
1.Servo Type Voltage Stabilizers 2.Electronic Type Voltage Stabilizers 3.Supervolt Power Voltage Stabilizers 4.Isolation Transformers A Voltage Stabilizer maintains a constant voltage level automatically, offering protection to equipment against voltage surges, under-voltage, or over-voltage while smoothing impulsive noise. WHAT ARE VOLTAGE STABILIZERS? A Voltage Stabilizer has been created to maintain a constant voltage level automatically, offering protection to equipment against voltage surges, under-voltage, over-voltage, whilst smoothing impulsive noise. A Voltage Stabilizer is also referred to as an Automatic Voltage Stabilizer, AC Voltage Stabilizer or Voltage Regulator. An Automatic Voltage Stabilizer has been created to automatically maintain a constant level of voltage so that your electrical equipment would be protected at all times against over-voltage, under-voltage as well as surges, leveling impulsive noise. Voltage Stabilizer is also called Automatic Voltage Stabilizer, AC Voltage Stabilizer or Voltage Regulator.
Eldee servo voltage stabilizers are available in a wide range and various models. The standard three phase models are suitable for balanced and unbalanced supply and loads.Our voltage stabilizers are available ranging from 1 kva-2000 kva As per required good
We supply Voltage stabilizer or Servo stabilizer or Voltage Regulator (AVR), Static voltage stabilizer, Static voltage regulator, Automatic voltage stabilizer, Automatic voltage regulator ranging from 500VA to 1000kVA in Dubai, Abu Dhabi, Sharjah, Oman, Doha & UAE. Our AVR has following features: 1) Wide input voltage range from +30% to -45% with option of ±15%, ±20%, ±25% & ±30%. 2) Reliable Output Voltage Stability. 3) Short Circuit and Overload Protection. 4) Microprocessor Controlled. Servo motor controlled. 5) High Overload Capability up to 200%. 6) Operation Capability at high Temperature and Humidity. Voltage Stabilizer. Voltage Regulator. Servo Stabilizer. AVR. Automatic Voltage Stabilizer. Automatic Voltage Regulator. Static Voltage stabilizer. Static Voltage Regulator. Common name for voltage stabilizers are voltage regulator, avr, servo stabilizer, servo motor controlled, automatic voltage stabilizer, automatic voltage regulator, static voltage regulator, SVR, voltage control, voltage fluctuation, sag, swell, Ortea, IEKO, stac, Stabica, stabilizer, voltage regulation, voltage controller, inverter, voltage stability, stabilizer, stabilizers, voltage regulators, automatic stabilizer, ac voltage regulator, ac voltage stabilizer ---------------------------------------------------------------------------------
(Using Variable Auto Transformer) Technology -controller based with digital signal processing Type Three Phase, 4 wire Make BHAGWATI Input Voltage Rangecustomized Output Voltage customized +/- 1% Input Frequency Range Hz Rate of correction 70 V/Sec Line to Line Efficiency - >98% at full load Type of Load Unbalanced Features:- � controller based technology with digital signal processing. Output voltage adjustment +/-10V. Output voltage On-delay 5 Sec. LCD display for all critical parameters. Continuous voltage and current monitoring for each phase. Load Power factor Unity Protection :- High / Low Voltage cut off at input and output Short circuit / Overload protection Input/Output Line - Neutral voltage monitoring. Load current monitoring for each phase. Single Phasing Protection.
Beta Power Controls, Coimbatore, India an ISO 9001:2015 TVE accredited company, leading manufacturing & Exports of Industrial Voltage Stabilizer, Isolation Transformers, Frequency Converter ,Two phase to three phase converter, Variable Transformer, Rectifiers energy saving equipment in India . Our products are well appreciated world over and received much recognition for their quality. Established in 2007 with a corporate objective to provide efficient energy for greener future,Beta power controls has grown to be one of the countryâ??s biggest manufacturers of power saving and power conditioning equipmentâ??s with the largest satisfied customer base. The products manufactured by us have made a distinct place in the market owing to their features like excellent performance, longer lifespan and less power consumption. With an objective to manufacture quality products, our experts use the latest equipment and best quality raw material provided by our trusted vendors of the market. We regularly Exports to Servo voltage Stabilizer in sudan.We are successfully meeting the varied requirements of our clients by providing the best quality range of 60kVA Oil Cooled Servo Stabilizers offered comprise highly functional Voltage Stabilizers that are designed using latest technology support so as to provide for optimum functional usage. These Voltage Stabilizers find extensive usage in controlling voltage fluctuations using solid state electronic circuitry. Being oil cooled stabilizers, these function as automatic line voltage correctors that use the synchronous motor that provides for optimum functional usage. Features: High efficiency & Fast response Wide input voltage range trip conditions 99.99% failure proof control circuit No over under, shoots and hunting Built in by pass switch up to 300 kVA Less active component avoids failure ratings Special electronic circuit to operate on gensets No effect of power factor and frequency variation The Voltage at speed related to the rate of fluctuations and avoids oscillations & hunting In AC motor drive Variable speed high torque ac servo motor proportionally controls corrections Separate isolated PCB for triac switching for the motor Protection: Input and Output Low/high Voltage protection. Phase rotation/single phasing preventer. Input protection using mcb / mccb. Output overload protection Surge control protection Input voltage range: Range I: 360 - 480 V Range II: 340 - 480 V Range III: 310 - 480 V *The input voltage, output voltage, frequency and phase can be custom made.
Specifications 1)Input voltage:303V~456V 2)Output voltage:380V 3)single phases 4)Output deviance: ¡¨¤2.5% 5)Frequency:50HZ/60HZ 6)Efficiency:>95% 7)Response time:0.2S~0.5S 8)Ambient temperature:-15 centigrates~+40centigrates 9) Instant overload capacity:1.5~2 times of rated current 10)Waveform distortion:Non-lack fidelity waveform 11)Features:contactless,noiseless,non mechanical and non carbon brush damage 12)Protect:overvoltage,overcurrent,fault diagnosis,signal display and alarm Other iterms as below: Model Rated Capacity Max output current Outline(L*W*H) SJW-10K 10KVA 15A 60*57*128cm SJW-15K 15KVA 23A 60*57*128cm SJW-20K 20KVA 30A 60*57*128cm SJW-30K 30KVA 45A 70*62*158cm SJW-50K 50KVA 76A 70*62*158cm SJW-100K 100KVA 152A 70*62*158cm SJW-150K 150KVA 227A 72*80*168cm SJW-180K 180KVA 273A 72*80*168cm SJW-200K 200KVA 303A 72*80*168cm SJW-225K 225KVA 333A 82*100*178cm SJW-250K 250KVA 379A 82*100*178cm SJW-300K 300KVA 455A 82*110*178cm
Reduction in motor efficiency, overheating and fast ageing of motors and switchgears Stoppage of production, inconsistent product quality and increase in wastage Malfunctioning & data loss in electronic/ cnc equipments Quick burn out of light fittings, bulbs & lamps Higher consumption by lighting load Higher demand & higher energy bill Loss of competitive position Capacity for servo voltage stabilizers -10 kva to 5000 kva
Automatic voltage stabilizers.
10 kva to 3000 kva capacity, 3 - phase, 50 hz. For different industrial applications. Input voltage range : 300 to 500 volts or as per Customers requirement Output voltage : 380/ 400/415 + 1% Depen upon caapcity
General Tm series servo ac voltage stabilizer adopt relay switch-over to adjust the output voltage, possessing the protection against tiomdelay, over voltage and under voltage the free switching between the electric supply and voltage stabilization, etc.It adopts the hanging type installation, which can effectively save and make sue of the space, the soft overall color of streamline gives people a bright and new look, it offer the advantages of quick work, accurate timing, steady performance, safety and electricitysaving, excellent design, reasonable constriction, easy operation, wide input voltage range, etc.The voltage stabilizers are the universal protectors in the high-grade household appliances, such as refrigerator, telecision, and so on. Application Lighting equipment,household appliance,air-conditioner equipment,sound equipment. CTN
Stabilizers : 10 kva to 3000 kva capacity, 3 - phase, 50 hz. For different industrial applications. Input voltage range : 300 to 500 volts or as per Customers requirement Output voltage : 380/ 400/415 + 1% or specific Automatic voltage controller the following advantages can be achieved. - reduction in failure rate of electrical equipment upto 60%. Energy saving 5 - 10%. Improvement in power factor and reduction in mdi. Uniform quality of end product. Better efficiency in plant. Depreciation @80% as per income tax act( in india only ) Depends upron capacity
Specifications:- Input : 340 V to 480 V AC OR As per customer demand Output : 415 ¬ 1% (Variable 5%) OR As per customer demand Capacity : Upto 1000 KVA Regulation : Better than ¬ 1% Winding : Copper wound Duty cycle : Continuous Frequency : 47 to 53 Hz Waveform distortion : Nil Power factor : Nil Ambient : 0 to 45¬ C Max Environment : Designed for indoor tropical use Mounting : Free on wheel Standard Accessories Controls Auto/ Manual selector switch Increase / Decrease selector switch Input / Output Volt selector switch Pot for variation in output in auto mode Protection under voltage/Over voltage cutoff at output Over load protection at Input Meter Voltmeter with input and output selector switch Indicating lamps Power ON, High/Low Voltage indication Optional Accessories Servo bypass switch Digital / Analog frequency voltmeter and Ammeter Start / Stop push buttons RFI Filter / Surge suppressor
FEATURES Power Rating500VA-10KVA / 5KVA-45KVA Power Factor0.8 Reset SwitchManual Reset Switch Bypass SwitchManual Bypass Switch For 3 KVA - 60 KVA, OPTIONAL IndicatorInput/Output Voltage (OPTION: VOLTMETER, NIXIE TUBE, LED, LCD) Operating Temperature0 ~ 40 C Relative Humidity0 - 90% MAIN TECHNICAL INDEX : SERVO SYSTEM(MICROPROCESSOR CONTROL FOR LCD TYPE) Voltage Regulatotion SystemServo Motor System Input Regulation System220V+15%/-25%(160-250V), 1 Phase (100V, 110V Option) Output Voltage Regulation220V+/-3%, 1 Phase (100V, 110V Option) Frequency50 Hz +/-5% EfficiencyBetter than 95% at full load, 198-220V input voltage Electric Appliance1500v/min no flashing nor puncture Insulation Resistancemore than 2M Ohm Output Wave FormSine wave (Synchronize with input wave form) Output Wave Form DistortionNo additional distortion Harmonic DistortionLess Than 0.5% Response TimeLess than 1 second (the input votlage changed 10%) PROTECTION SYSTEM (OPTIONAL) Surge ProtectionAutomatic shutdown Overlaod ProtectionCircuit breaker or Fuse Time Delay- Short time delay: 5 seconds ± 2 seconds - Long time delay: 5 minutes ± 2 minutes Automatic Shutdown- Output voltage out of limits: 245±5V, Manual Reset - Output voltage out of limits: 185±5V, Automatic Reset - AC voltage flicker - Output Short Circuit - Phase fault - Power failure or Interruption - Power semiconductor failure OTHER Acoustic NoiseLess than 40dB Warranty periodOne year (for free) from the date of B/L. Free product accessories will be sent to you and save your maintain cost ApplicationOffice equipment, test equipment, medical equipment, industrial automation equipment, household appliance,lighting system, communication system, etc
What Is Servo Voltage Stabilizer The Servo voltage stabilizer maintains the quantity of voltage in the power system, even in the case of voltage fluctuations. The control element basically converts the unregulated input to the regulated output. GENERAL SPECIFICATION The product range offered by us is inclusive of Servo Stabilizers, Electronics Plating Rectifiers and Electronics Rectifiers. Their longer serving life, compact design, less power consumption, easy operation and low working cost, makes these machines highly appreciated among our patrons. The offered range finds wide applications in various commercial, industrial and household applications. Offered by us at industry leading prices, these electronic and allied machines and equipment are highly appreciated among our patrons. We are Best manufacturer of Servo Voltage Stabilizer and Rectifier. Rating: Up to 5000 KVA Feature 1) There is high speed chip controller as brain behind the control board, 20x4 LCD to display instantaneous electrical parameter 2) Self teaching type Front panel for parameter setting 3) Smart and Intelligent to control overload based system 4) User settable Output voltage Upper and Lower voltage cutoff based on output set value 5) There is Individual message for each fault. 6) Single board for control and conditioning 7) For alarm On board buzzer 8) User settable Buzzer control 9) Very simple for wiring and maintenance 10) Fault history storage facility and can store No. of faults 11) System ON/OFF control through Front panel soft key for maintenance 12) Three phase separately can be controlled independently through single board In analog type servo voltage Regulator, it requires separate digital meter and overload facility is normally not provided All the settings are provided as factory setting, users have very less option to set. Advantages & Benefits 1) Higher reliability and performance, easy for user 2) Easy to change output parameter as per customer need 3) System will not allow more than system power rating 4) Load will be always safe from the output over voltage 5) Very Easy to find out unhealthy status of servo or load. User can take preventive action based on this indication. 6) User will get buzzer for all kinds of faults to recognize system status without visualizing 7) Reduced wiring will increase reliability in the system, lesser probability of failure malfunction. 8) Very good feature of Digital controller, user will always be aware with load pe Conditioning. User himself can take preventive actions. This will reduce time to 9) This will provide correct information of how much maximum voltage and load c sustained by the System. From this preventive action can be taken for the load.
GALATA SERIE DVR-M3H Full Automatic Servo Dynamic Voltage Regulator DVR-M3 150KVA THREE PHASE The DVR-M3H Regulator provides the following: -Protection of the user from negative voltages. -Protection of the user and the device from excessive current. -Undisturbed pure sinus voltage regulation. -Long-term overload protection and short-term protection. -AC voltage balancing with extremely high accuracy. -Run smoothly on all loads from 0% to 100%. -Manual transfer to bypass regime without regulating. -Display all values against the probabilities in the bypass regime. -Record mains input voltage limits and load current values. -Static, not gradual, dynamically correct output voltage too quickly without user notice. -When protections are activated, record the number of protection trips and the reason for each parameter separately. -Generation as standard is 0.4% (379.87V - 382.6V) stable when the input voltage is within the range of 112.6V ..... 537V. TECHNICAL SPECIFICATIONS INPUT Input Voltage Correction Range :190-415 / 275-450 / 310/485 VAC Input Voltage Operating Range : >155v...490v< Operating Frequency : >47.....64 < Input Protection : Overcurrent. Low and High Voltage Protection (Optional) OUTPUT Output Voltage : >380v...415v< +/- %0,4 Overload :10 SECOND % 200 load Correction Speed / Recovery Speed : - 90 Volt / S (150-250VAC the range) Output waveform : Pure Sine Output protection : Overcurrent. Low and High Voltage Protection (Optional) Output protection at low voltage : 337V on - 303V off Output protection at high voltage : 424v on ... 433 off OPERATING PRINCIPLES : Servo Motor - Microprocessor - Dynamic Servo GENERAL Cooling : Smart fan system (Thermostat) Measurement and imaging : Input and Output Voltage Led Display / Input, Output Voltage and Ampere Led Display MULTIMETER Continuous operating time at full load : 0..105%. Continuous load 96% Mechanical By-pass : Manual control network / 1-0-2 Pako Switch / Remote Switch / Lock key On / Off Protection Class : IP20 and Other Options
FATIH SERIE DVR-M3H FULL AUTOMATIC SERVO DYNAMIC VOLTAGE REGULATOR DVR-M3H 250KVA THREE PHASE The DVR-M3H Regulator provides the following: -Protection of the user from negative voltages. -Protection of the user and the device from excessive current. -Undisturbed pure sinus voltage regulation. -Long-term overload protection and short-term protection. -AC voltage balancing with extremely high accuracy. -Run smoothly on all loads from 0% to 100%. -Manual transfer to bypass regime without regulating. -Display all values against the probabilities in the bypass regime. -Record mains input voltage limits and load current values. -Static, not gradual, dynamically correct output voltage too quickly without user notice. -When protections are activated, record the number of protection trips and the reason for each parameter separately. -Generation as standard is 0.4% (379.87V - 382.6V) stable when the input voltage is within the range of 112.6V ..... 537V. TECHNICAL SPECIFICATIONS INPUT Input Voltage Correction Range :190-415 / 275-450 / 310/485 VAC Input Voltage Operating Range : >155v�490v< Operating Frequency : >47.....64 < Input Protection : Overcurrent. Low and High Voltage Protection (Optional) OUTPUT Output Voltage : >380v�415v< +/- %0,4 Overload :10 SECOND % 200 load Correction Speed / Recovery Speed : - 90 Volt / S (150-250VAC the range) Output waveform : Pure Sine Output protection : Overcurrent. Low and High Voltage Protection (Optional) Output protection at low voltage : 337V on - 303V off Output protection at high voltage : 424v on ... 433 off OPERATING PRINCIPLES : Servo Motor - Microprocessor - Dynamic Servo GENERAL Cooling : Smart fan system (Thermostat) Measurement and imaging : Input and Output Voltage Led Display / Input, Output Voltage and Ampere Led Display MULTIMETER Continuous operating time at full load : 0..105%. Continuous load 96% Mechanical By-pass : Manual control network / 1-0-2 Pako Switch / Remote Switch / Lock key On / Off Protection Class : IP20 and Other Options
Being one of the reputed organizations in the market, we are engaged in manufacturing and supplying an exclusive range of servo stabilizer. The offered voltage stabilizers are manufactured using the best quality components and progressive technology. Our provided stabilizers are widely demanded by our esteemed clients, due to their high strength and rust free nature. Apart from this, offered voltage stabilizers are designed in various sizes and specifications as per the needs of the clients. Features: Maximum workability Low power consumption Elevated service life
FEATURES > Specially designed high-performance controller-based control circuit for ultra-high reliability. > Key Parameters adjusted through user interface for the Digital Control Unit > High efficiency>98% > Fast correction speed up to 75 V/ Sec. variable speed servo motor and proportional control circuit provide a response time of 10msec to correct voltage fluctuations without noise or oscillations in output. >Accuracy �± 1% from no load to full load > Auto/manual operation facility. > Plug and play a single control card for easy serviceability. > Reduced power loss and resultant lower running cost yield higher cost savings and help the customer recover the cost difference in a few months.
Specifications 20kVA Input Phase Three phase Voltage AC 280~430V AC 304~456V Frequency 50 Hz Output Voltage 380�± 3 % (Adjustable) Capacity 16kW 24kW 32kW 48kW 72kW 80kW Frequency 50Hz Protection Under volt AC 318 �± 7 % Over volt AC 426 �± 7 % Delay 3-7 sec/3-7 Min (Optional) Over load Yes Bypass Manual Short phase Yes Cooling system Natural Cooling System Efficiency AC-AC > 95% Environment Humidity 20 % to 90% Temperature -50 C ~450 C Control System Step less control with servo motor, Individual phase control
