Features: 1. Our pumps applied the single or double vane structure so that it can transfer sewage easily. It can transfer the fibrous matter which is with bore 5 times than pumps. 2. Seal the pumps with material tungsten carbide which is new, tough and corrosion resistant. All the same time we seal up the pumps with double-end, make it working in the oil chamber with long time safely, at least more than 8, 000 hours. 3. The structure of our pumps is portable, minimum-volume, non-noise and distinct energy-saving effect. Our pumps are convenient to repair and they can work as long as been put in water, this will save the cost much. 4. We installed the leak detection sensor which is high-precision and anti-jamming in the sealed oil chamber which can protect the pumps totally. 5. We can equip the automatic safety control cabinet according to the request from customer. Protect the leak, over-temperature and over-weight totally. 6. Float switch can adjust automatic according to the liquid, it can control the start and stop of pump, need not person to operate, it is very convenient for using. 7. We can equip double guide rail automatic coupling installation system according to the needs from customer; it can be convenient for repair and installation. 8. Our pumps can be used in the range and assurance the electrical machinery will not be overload. 9. There is 2 ways for installation: fixed type automatic coupling installation system and mobile free installation system.
Vacuum Carburizing Furnace Introduction: ShinTek Vacuum Carburizing Furnace can be used for Quenching and Carburizing varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Carburizing Furnace Specifications: Model STVF-Q-40 STVF-Q-65 STVF-Q-85 STVF-Q-120 STVF-Q-160 STVF-Q-240 STVF-Q-500 Working zone size 450*300*300 600*400*400 750*500*500 900*600*600 1100*700*700 1200*800*800 3500*800*600 Load (KG) 60 150 250 500 800 1000 2500 Power 40KW 65KW 85KW 120KW 160KW 240KW 500KW Max. temperature 1350? Temperature uniformity +/-5? (can achieve +/-3?for some specific project.) Ultimate vacuum level (Cold) 5*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Carburizing Furnace can be customized for your specific project. Vacuum Carburizing Furnace features: (1) Vacuum Carburizing Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Carburizing Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Carburizing Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Carburizing Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Carburizing Furnace – Friendly control system. The main difference between Oil Quenching and Gas Quenching: 1. Oil Carburizing – Total investment is lower; 2. Gas Carburizing – Small deformation on the parts after treatment; Do not need clean after treatment.
Vacuum Heat treatment Furnace Introduction: ShinTek can produce varieties of vacuum heat treatment furnace, including Vacuum Quenching Furnace, Vacuum Annealing Furnace, Vacuum Tempering Furnace, Vacuum Carburizing Furnace etc…which can be used for heat-treating varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Heat Treatment Furnace Specifications: Model STVF-Q-40 STVF-Q-65 STVF-Q-85 STVF-Q-120 STVF-Q-160 STVF-Q-240 STVF-Q-500 Working zone size 450*300*300 600*400*400 750*500*500 900*600*600 1100*700*700 1200*800*800 3500*800*600 Load (KG) 60 150 250 500 800 1000 2500 Power 40KW 65KW 85KW 120KW 160KW 240KW 500KW Max. temperature 1350? Temperature uniformity +/-5? (can achieve +/-3?for some specific project.) Ultimate vacuum level (Cold) 8*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Heat treatment Furnace can be customized for your specific project. Several hotzone design for choose: Horizontal, Vertical; Vacuum Heat Treatment Furnace features: (1) Vacuum Heat Treatment Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Heat Treatment Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Heat Treatment Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Heat Treatment Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Heat Treatment Furnace – Friendly control system.
Vacuum Annealing Furnace Introduction: ShinTek Vacuum Annealing Furnaces can be used for annealing varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Annealing Furnace Specifications: Model STVF-A-80 STVF-A-100 STVF-A-150 STVF-A-200 Working zone size 600*400*400 750*500*500 900*600*600 1200*800*800 Load (KG) 200 300 500 1000 Power 80KW 100KW 150KW 200KW Max. temperature 1100? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 5*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Annealing Furnace can be customized for your specific project. Vacuum Annealing Furnace features: (1) Vacuum Annealing Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Annealing Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Annealing Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Annealing Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Annealing Furnace – Friendly control system.
Vacuum Tempering Furnace Introduction: ShinTek Vacuum Tempering Furnaces can be used for Tempering varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Tempering Furnace Specifications: Model STVF-T-80 STVF-T-100 STVF-T-150 STVF-T-200 Working zone size 600*400*400 750*500*500 900*600*600 1200*800*800 Load (KG) 200 300 500 1000 Power 80KW 100KW 150KW 200KW Max. temperature 1100? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 5*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Tempering Furnace can be customized for your specific project. Vacuum Tempering Furnace features: (1) Vacuum Tempering Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Tempering Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Tempering Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Tempering Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Tempering Furnace – Friendly control system.
portable fire water monitor water cannon Features 1.Weight of this fire monitor is less than 32kg, can be operated by one person; 2.Automatic pressure-regulating nozzle, constant injection pressure. Fixed rubber atomizing teeth, good heat absorption effect, can be installed with foam tube; 3. The flow rate is 60-80 L/S, two 80mm (3) double water inlets, if one water inlet is used, the other water inlet will be closed automatically; 4. 360 degree rotary inlet joint to prevent hose knotting; 5.The supporting feet can be folded for easy storage, and the positioning operation can be carried out by pulling the foot spring; 6. The foot supports are equipped with anti-skid tungsten steel nails to prevent the water monitor/cannon from sliding during operation, and the tungsten steel nails are equipped with spring damping mechanism, which can be adjusted automatically on uneven road and play the role of buffering recoil force; 7. Made of Light aluminum alloy, surface anodized
Cylindrical Diamond grinding wheels Description of the Cylindrical Diamond grinding wheels: Cylindrical Diamond grinding wheels are mainly used for grinding tungsten carbide coating, ceramic coating and others material. Various kinds of dimensions and shapes are available, such as flat shapes, cup shapes, dish shapes, etc. Feature/Benefit of the Cylindrical Diamond grinding wheels 1. Good free-cutting 2. Good Abrasion Resistance 3. Availability in a broad range of applications in both Dry and Wet Condition 4. Improved Heat Resistance Application of the Cylindrical Diamond grinding wheels: 1. Internal grinder, 2. Tungsten carbide grinding, 3. Wet or dry grinding Specification of Cylindrical Diamond grinding wheels: Type: 1A1,1A8, 1A1W � Bond type: Resin, electroplated, metal type Grit: 50 2000 Concentration: 100, 125 to meet your requirements in every way, we need the following information Shape and Dimension of the wheels Grit size (Mesh, refer to Table 1) Concentration Bond(Resin, Vitrified, Metallic, Electroplated) Quantity
Resin bond diamond Internal Diamond Grinding Wheel for HVOF coating Description of the Resin bond diamond Internal Diamond Grinding Wheel for HVOF coating: Resin bond diamond internal grinding wheels are mainly used for grinding tungsten carbide coating, ceramic coating, and other materials Various kinds of dimensions and shapes are available, such as flat shapes, cup shapes, dish shapes, etc. Feature/Benefit of the resin bond diamond interal grinding wheel 1. Good free-cutting 2. Good Abrasion Resistance 3. Availability in a broad range of applications in both Dry and Wet Condition 4. Improved Heat Resistance Application of the Resin bond diamond Internal Diamond Grinding Wheel for HVOF coating: 1. Internal grinder, 2. Tungsten carbide grinding, 3. Wet or dry grinding Specification of resin bond diamond internal grinding wheel: Type:Â 11,18, 11W Bond type: Resin, electroplated, metal type Grit: 50 2000 Concentration:100,125 to meet your requirements in every way, we need the following information Shape and Dimension of the wheels Grit size (Mesh, refer to Table 1) Concentration Bond(Resin, Vitrified, Metallic, Electroplated) Quantity
Vitrified bond diamond Internal Diamond Grinding Wheel for HVOF coating Description of the vitrified bond diamond Internal Diamond Grinding Wheel for HVOF coating: Vitrified bond diamond wheels are mainly used for grinding tungsten carbide coating, ceramic coating, and other materials. Various kinds of dimensions and shapes are available, such as flat shapes, cup shapes, dish shapes, etc. Feature/Benefit of the vitrified bond internal diamond grinding wheel 1. Good free-cutting 2. Good Abrasion Resistance 3. Availability in a broad range of applications in both Dry and Wet Conditions 4. Improved Heat Resistance Application of the vitrified bond Internal Diamond Grinding Wheel for HVOF coating: 1. Internal grinder, 2. Tungsten carbide grinding, 3. Wet or dry grinding Specification of vitrified bond internal diamond grinding wheel: Type: 11,18, 11W � Bond type: Resin, electroplated, metal type Concentration: 100, 125 to meet your requirements in every way, we need the following information
CBN Grinding Wheel for Micro Drill Model: 3A1 resin diamond grinding wheel Application: small diameter tungsten, stainless steel or hss drills, micro drills, and end mills used in electronics, medical technology, and the automotive industry Alias: resin diamond wheel, 3A1 diamond wheel Application: Micro Drill Precision Grinding Applications Of Diamond Grinding Wheel Resin diamond grinding wheel is mainly used for small diameter tungsten, stainless steel or hss drills, micro drills, and end mills used in electronics, medical technology, and the automotive industry Advantages Of Diamond Grinding Wheel For Micro Drill Good edge stability, High cutting efficiency, Minimal reject-part rates, Good round tool quality Suitable Grinding Machine Startech, Kimer K360, Rollomatic, SAACKE, HAWEMA, Walter Helitronic, ANCA, Schneeberger Norma, DMG MORI, WAlter, EWAG and other all CNC tool grinding machines
Resin bond vitrified bond diamond grinding wheel Description Vitrified products have the features of sharp cutting ,high efficiency, long life, less heat and jam generated in grinding, easy control of precision and easy dressing. we can provide vitrified superabrasive grinding wheels diameter range is 8-750mm ; the tickness range is 1-300mm; the grit size range is 60/70-W3.5. Application: vitrified diamond products: mainly used for machining tungsten carbide, PCD, PCBN, ceramic , cermet, etc. Electroplated products: Description: The electroplated grinidng wheels have characteristics of high grain density , sharp grinding, high effiecncy, good precisiion, without dressing etc. The product can be made with various shapes and they sare suitable for special complicated profile, super-thin, especially small and other form grinding which have strict requirement on geometry shape and dimension. Therefore it improves the process efficiency and a lot of tools which are difficult to process with other methods can be sloved here. Applicaton: Electroplated diamond products: mainly used for machining nonmetallic materials with high rigidity like ceramics, glass, tungsten carbide, ferrite and so on. Electroplated CBN products: mainly used for machining metallic material such as chilled cast iron,founded alloy steel, titanium alloy and so on.
Nameï¼?Grinding Wheel For CNC Tool Grinder Type: 1A1, 1V1, 11V9, 12V9, 14A1 Brief Introduction: CNC Tools Grinding Machine with a very excellent Stability and high flexibility, it??s requirement for the Diamond and CBN grinding wheel for CNC machine with high efficient grinding, good wear resistance ,good shape retention and high material removal rate . Application: tungsten carbide, HSS, drill Details More SuperHard diamond / CBN grinding wheel for CNC tool grinder is used for tungsten carbide, high speed steel (HSS), stainless drill ,end mill and reamer. We will provide a complete solution for CNC tools manufacturing process, including fluting, gashing and Clear edge, relief angle grinding . CNC tools grinder: Walter, ANCA, EWAG, Farman, Schutte, Schneeberger, Makino, Stuer, Strausak, Cininnati, Griffo, Huffmann, Jungner, CUOGHI, Fehlmann and so on. Meanwhile, More Superhard Products Co,.Ltd also supplies diamond cutting disc for carbide rods cutting, centerless grinding wheel for carbide bars, silicon carbide wheel for dressing CNC grinding wheel (dressing machines: Cleveland , Farman) and so on. Please don't hesitate to contact me if you have any needs:miya AT moresuperhard.com Our company also produces a series of diamond and CBN tools,welcome to consult and choose at any time
Material: Tantalum. Chemical Composition: Tantalum (Ta)= 34,7 % Niobium (Nb)= 12,5 % Titanium Dioxide (TiO2)= 0,88 % Tungsten(W) = 10,8 % Vanadium (V)= 11,2 % Hafnium (Hf) = 12,5% Packaging: container. Delivery: ready for shipping. Min Purchase Order: Minimum Quantity: 26 MT (metric tons) Max Purchase Order: 1200 MT per month with production increases. The business model shall initially be tested with a 26 MT purchase order (PO). Thereafter, the quantity could be increased as demanded. For large POs, a face-to-face meeting is a requirement. Price: Will be sent by email
Hastelloy C276 is a superalloy that wires molybdenum and nickel and has some element of tungsten that gives amazing detaching control and quality in the wide component of extraordinary temperature and condition. On the off chance that you are finding the correct maker who offers Hastelloy C276 bars, by then we would suggest you purchase these bars They are one of the unmistakable makers who give the best and stunning nature of bars in various structures and shapes as appeared by the interest and need of clients. They utilize unimaginable quality grungy material and current advancement to give positive length, size, and plan to these bars. Their destroying get-together of bosses conducts different tests to make these bars of high bore.
Zhuzhou WeiRe New Material Technology Co., Ltd. (WeiRe New Material) is located in Zhuzhou, Hunan Province, China Power Valley, specializing in the production of Wre /TZM,W/Cu,Mo/Cu and other refractory metal matrix high-performance composites.By doping other elements in tungsten and molybdenum groups, the material is endowed with extraordinary performance. According to different needs, the materials are synthesized into composite materials. By virtue of the advanced material preparation technology and the strong technical development strength of Central South University, the company's technical achievements have reached the international advanced level.
Ore color sortet to remove impurities from valued minerals by color difference in processing plants. Details Industrial mining color sorter usually applies to ores that needs to be separated from the impurities, based on the difference of colors, the ore color sorter could apply to all types of ore color choose, include but not limited to ores such as quartz, silica sand, coal, manganese, tungsten, phosphate rocks etc. usually the belt type ore color sorters are more productive, they could transfer the material through the color separation section of a bin to the outlet, at the far end of the color separator, the impurities will be separated from the fine product by the difference of their colors.
Shaking table, as one of the gravity mining machines, applicable to nonferrous metals, ferrous metals and rare metals mineral, like gold, tungsten, tin, tantalum, iron, manganese, chrome, titanium, bismuth and lead, which the size ranges from 2-0.037mm, also recovery of Au, Cu, Ag from various of slags, PCB, waste wire and cable, battery scrap, to improve recovery ratio and protect environment. Recovery material size ranges are: coarse sand (0.5 mm to 2 mm), fine sand (0.074 mm to 0.5 mm) and slime (-0.074 mm). Effective mineral recovery size range is 0.22 mm to 2 mm.
Description Three Disc Separator is for a variety of strong magnetic minerals mixed ore separation, according to the difference of magnetic minerals.It can form different intensity magnetic disk by adjusting the excitation current levels, and also be adjusted each level disk and sensing distance between dressing grain is to get different magnetic induction intensity, reaching a onetime separation of various minerals. This device is widely used in tungsten tin, tantalum,iron ore and other minerals with magnetic and non-magnetic dry sorting. Features >> Simple structure, easy operation, convenient installation and adjustment. >> High efficiency, less power consumption. >> Stable working, reliable performance and long working life.
Dongguan AoFei jewelry Co., Ltd, is located in the town of Changan economy strong town of Dongguan city. The company mainly engaged in:Germanium chip, Germanium ball,Germanium beads,Germanium ring,Germanium kneecap,Germanium elbow pads,Germanium waist support,Terahertz Health energy stone,Titanium bracelet, titanium necklace,Tungsten Bracelet,Stainless steel bracelet, stainless steel necklace,Germanium beauty massage products,Fashion jewelry, etc. This beaded bracelet is made of pure germanium beads. We also have silver with germanium beaded bracelets If you want to get more
PCD disc CBN tip cutting tools blanks diamond tool segment PCBN is made by high pressure high temperature sintering of cubic boron nitride with a binder phase, and there are mainly tow groups of binders, namely metal binder and ceramic binder. CBN and diamond are very similar in crystal structure,chemical bond and lattice parameters,thus they perform quite similar hardness and strength. In cutting applications, thewear resistance of PCBN exceeds 50 times that of tungsten carbide. If you need any products, do not hesitate to contact PCD PCD(Polycrystalline Diamond)is a synthesized, extremely tough, intergroup mass of randomly orientated diamond particles in a metal matrix. It is produced by sintering together selected diamond particles at high pressure and temperature. 51mm diameter round shape PCD cutting tools PCD blanks 1. The introduction of PCD cutting tool blanks(PCD cutter/ PCD blanks) : PCD cutting tool blanks are composed of diamond powder and tungsten carbide in high temperature and pressure. They have the high hardness and abrasion resistance of nature diamond, and combined with the toughness that of tungsten carbide 2.The Application of PCD cutting tool blanks(PCD cutter/ PCD blanks): Suitable for the machining of non-ferrous metal and alloys, such as aluminum, copper, zinc, as well as wood, ceramics, rubber, plastic, fibre, etc. 3. Some useful tips of PCD cutting tool blanks(PCD cutter/ PCD blanks): The normal shape is round, also could be cut into rectangles, triangles, sectors, etc. as request. The main controlling factor determining PCD grade(the work piece surface finish and the abrasion resistance(tool life) )is the grain size. It is generally accepted that abrasion resistance increases with increased grain size, and the work piece surface finish are increases with the decreasing grain size. The medium grain size PCD blanks are generally used for their ability to strike a balance between good abrasion resistance (tool life) and maintaining good work piece surface finish. The PCD blank is thermally stable up to 750°C, so its better to be welded with silver solder in a very short time, otherwise will cause carbonizing reaction or crack.
