Introduction This machine is composed of screen box, vibrating motor, damping system and bottom rack. Screen box is consisted of deck base, screen plate, scale-board etc. It adopts high function and long life YZO series vibrating motor or exciter as exciting source to adjust the size of exciter force, in order to change swing of sifter machine. The damping system is made up of rubber spring, hoop and supporting base. The bottom rack is consisted of hopper and chasis rack, installation method of exciter source is divided into upper vibrating or under vibrating, installation method of vibration reducer is divided into base or suspention. We also can design and manufacture according to users requirement. Working Principle Screen self-synchronous reversed rotation depends on two sets of same vibrating motors or general motors along with exciter, and makes the whole screen machine supported on vibration reducer moves on a linear trajectory quickly go ahead and loose to complete screening operation after materials fall into screen from inlet. XBZS series cantilever bar vibrating sifter is driven to rotate synchronously in opposite directions by two same vibration motors or electric motors with exciters, which makes the screen body move on periodical and to-and-fro linear trajectory to achieve screening classification. Features The deck of bar screen should be inclined installed, the angle is during 20 degree to 35 degree. When comparing with other same type has following difference: 1.small volume , big inclined angle and screening capacity. 2.light weight, easy installation. 3.low price and energy consume. 4.simple construction and beautiful shape. 5.the efficiency of the screen mesh is more over 20% than the general screen mesh. 6.self-cleaning. 7.specially using for secondary screening under the high furnace groove. 8. Large inclination installation of screen surface(20°-35°), small volume, large capacity. 9. Light weight for easy installation;low power consumption for energy-saving. 10.Low cost and little spare parts;simple structure and attractive appearance. 11.Self-cleaning function, specially for secondary screening below blast furnace bin. Application XBZS series bar screen is a new type screen equipment , Suitable for the classification of big materials, medium and small granular materials. it is widely used in mining, coal, energy power, metallurgy, building materials, fire-resistant, etc.
1. DP27 Pilot Operated Pressure Reducing Valve: Pressure Rating: 1.6- 2.5Mpa. Specification: DN15-50. Material: Steel WCB. Standard flanges: DIN, ANSI, JIS. 2. DPP17E Pilot Operated Pressure Reducing Valve: Pressure Rating: 1.6- 2.5Mpa. Specification: DN15-50. Material: Steel WCB. Standard flanges: DIN, ANSI, JIS. 3.DP17 Pilot Operated Pressure Reducing Valve: Pressure Rating: 1.6- 2.5Mpa. Specification: DN15-50. Material: Steel WCB. Standard flanges: DIN, ANSI, JIS. 4. DP143 Pilot Operated Pressure Reducing Valve: Pressure Rating: 1.6- 4.0Mpa. Specification: DN15-200. Material: Steel WCB. Standard flanges: DIN, ANSI, JIS. 5.Y14H/F Direct Acting Bellows Pressure Reducing Valve: Pressure Rating: 1.6- 2.5Mpa. Specification: DN15-25. Material: CF8. Standard screwed: NPT,BSP. 6. BRV71 Direct Acting Bellows Pressure Reducing Valve: Pressure Rating: 1.6- 2.5Mpa. Specification: DN25-50. Material: Steel, CF8. Standard flanges: DIN, ANSI, JIS. Standard screwed: NPT, BSP. 7. Y44H/Y Direct Acting Bellows Pressure Reducing Valve: Pressure Rating: 0.6- 1.6Mpa. Specification: DN15-100. Material: Steel, CF8. Standard flanges: DIN, ANSI, JIS. 8. YK43F/H Pilot Piston Type Gas Pressure Reducing Valve: Pressure Rating: 1.6- 16.0Mpa. Specification: DN15-500. Material: Steel WCB, CF8. Standard flanges: DIN, ANSI, JIS. 9.Y43H Pilot Piston Type Steam Pressure Reducing Valve: Pressure Rating: 1.6- 16.0Mpa. Specification: DN15-500. Material: Steel WCB, CF8. Standard flanges: DIN, ANSI, JIS. 10. Y42F Direct Action Spring Diaphragm Type Pressure Reducing Valve: Pressure Rating: 1.0- 2.5Mpa. Specification: DN15-500. Material: Steel, CF8. Standard flanges: DIN, ANSI, JIS. 11. RP-1H Steam Pressure Reducing Valve: Pressure Rating: 1.6- 16.0Mpa. Specification: DN15-500. Material: Steel, CF8. Standard flanges: DIN, ANSI, JIS. 12.Y42X Direct Action Piston Type Pressure Reducing Valve: Pressure Rating: 1.0- 6.4Mpa. Specification: DN20-400. Material: Steel, CF8. Standard flanges: DIN, ANSI, JIS.
What is Rotary Kiln? Rotary kiln is composed of cylinder, gears, support device, kiln liner and kiln tail sealing equipment, kiln head hood and combustion. Cylinder as heated pivoting part, made of high-quality carbon steel plate. Rotary Kiln Features: 1. Support device: advanced shaft structure, automatic temperature measuring device and electrical heating,. 2. Catch wheel: including two kinds mechanical wheel and hydraulic pressure 3. Gears: single or double. Control the rotating speed by buncher, DE machine and frequency variable motor. Be reliable, energy-saving, and efficient. 4. Cylinder tyre bolster: lower bolster has three types: fixed, zoom and floating. The structure is simple, replacement is convenient and won¡¯t hurt cylinder. 5. Sealing equipment: there are many kinds for choice according to kiln models, including air cylinder edge sealing, spring edge sealing, and graphite block sealing and combination for above. 6. Kiln head hood: including stationary type and flexible type. Working Principle of Rotary Kiln: 1) With a certain slope to the level, the whole kiln body is supported by rollers and fitted with thrust rollers to control up and down movement of the kiln body. 2) Besides main driving unit for driving system, it is also fitted with the auxiliary driving unit so as to ensure the kiln body still can rotating when the main motor is powered off and prevent it from deforming. 3) The kiln head adopts housing type sealing and kiln rear uses axial contact sealing unit so that reliability of sealing could be ensured. Types: Rotary kiln belongs to building material equipment, and it can be divided into cement kiln, metallurgy chemical kiln and active lime kiln, porcelain kiln according, building material kiln, calcined petroleum coke rotary kiln to different materials. Application of Rotary Kiln: 1) Rotary kiln is the Thermal Equipment, heating materials, in cement industry for calcining clinker. 2) It is also used in various industries, such as cement, nonferrous metallurgy, ferrous metallurgy, chemistry, building, refractory material, environmental protection, etc. Export standard container 20GP OR 40GP, 40HQ, FR container, in bulk, the spare parts in wooden case.
200 amp High Voltage Outdoor AC Disconnector Description & Application AC outdoor high voltage disconnect switch is mainly applied in AC10~40.5kV, 50Hz power system. It is widely used in electric power, railway, mining and oil field. And all fittings not only reasonably& integrally designed but also made of high quality materials. Technical Parameter & Detail Show Technical Parameter Insulator Material: Silicone Rubber Rated Voltage: 12kV Rated Current: 200A,400A,630A,1000A,1250A Rated Frequency: 50Hz,60Hz Rated Lightning Impulse Voltage Withstand: 95kV(phase to earth) 110kV(across isolating distance)ltage: 50kV(phase to earth) 60kV(across isolating distance) Distance between Interrupting Points: ¡Ý205mm Rated Short Time Current Withstand: 25kA,20kA, 16kA/4S Rated Peak Current Withstand: 40kA,50kA Mechanical Life: 2000 times Creepage-distance: ¡Ý410mm Material Conductive contact parts---All the parts are over 20¦Ìm silver coating, preventing from oxidation easily. Insulator--- Silicone Rubber insulator has the performance of light weight, waterproof and non-brittle. Base plate---Stainless steel or hot galvanizing base ensures reliable manipulation & corrosion resistance. Feature & Advantages 1 Stainless steel disc spring bowl¡ª It makes two contact parts much more tighten, and supplies very low resistance. 2 Operation pull ring--- The lever design of pull ring and shift lock-pin ensures high breaking ability. 3 Contact methods---using surface contact instead of point contact, the device prevents too large resistance leading to heat too fast, and provides fire protection as well. Standard The design and test of SSOD disconnect switch are complied with the following standards: ISO9001 IEC62271-102 GB/T 11022-1999 GB 1985-2004 GB/T 5582-1993 GB/T 311.2¡ª2002 Shipping Sea Way Air Way Express PaymentPayPal West Union wire Transfer T/T We¡¯re always at your service, any question please feel free to contact us.
Main function : HZ-1001A Tensile testing machine mainly applied to test the froce of metallic and non-metallic materials, the force such as tension, compression, bending, shear,peel, tear or two-points extensions (need to add extensometer) and others., the material such as rubber, plastic, wire and cable, optical fiber and cable, safe belt, leather belt composite materials, plastic profiles, waterproof membrane, steel, copper, profiles, spring steel, bearing steel, stainless steel, castings, plate, strip, non-ferrous metal wire. Adopted photoelectric encoder to measure the displacement, the controller uses the embedded single-chip microcomputer structure with multi-function software, which combined with measurement, control, culculation and storage. It can automatic calculate the stress, rate of elongation (need to add with extensometers), tensile strength, elastic modulus, automated statistical results;automatically recorded the biggest point,breaking point, the designated point value or the rate of elongation; Using computer to display the dynamic curves in the testing process and process the data,After testing, it can re-analysis and editing the data by amplifying the curves through the graphics processing module, printing reports, product performance reached the international advanced level. Corresponding standard : GB/T16491-1996 electronic universal testing machine . Applicable industry : It is widely used in controlling the quality; Rubber & Plastics; metallurgical iron and steel; manufacturing machinery; electronic equipment; automobile production; textile fiber; wire and cable; packaging materials and foodstuffs; instrumentation; medical equipment; civilian nuclear energy; civil aviation; colleges and universities; research Laboratory; inspection arbitration, technical supervision departments;building materials, ceramic; Petroleum & Chemical; other industries. Technical parameter : model: HZ-1001A universal material shear testing machine Maximum load: 2ton, 5ton, 10ton( optional) Accurate grade:1 grade /0.5 grade Effective measuring range:From 0.2% to 100% (1 grade) / From 0.4% to 100% (0.5 grade) Tester resolution: Max load 1/200000, constant the resolution Load sensor: Basic configuration sensor max load: one Effective testing width: 400mm (can be widened according to customers requirement ) Effective tensile space: 400, 500, 600mm (can be increased the height according to customers requirement) Testing speed: from 0.001 to 500mm/min Tolerance: 0.5% / tolerance: 0.2% Min span :10mm, Max range of deformation 800mm Another configuration:Min span: 25mm, 50mm, 100mm. Max range of deformation 5mm, 10mm, 25mm. By standard export wooden case.
Dot hydraulic brake hose Standards: fmvss 106 dot, sae j1401, ms-ea70, esa-m96d4-a, gm6403m, iso 3996, jis d2601, fr31302 1973, adr 7, ntc 977, tl-vw 821 52, gb16897-97 etc Application: vehicle with hydraulic brake system. Car, passenger cars, multi-purpose passenger vehicles, light truck, trucks, buses, trailers, light commercial vehicle, jeep, motorcycle, scooter, atv, forklift, snowmobile, three wheeler etc. Feature: Low volumetric expansion, Ozone and uv resistance, Exclusive whip dampener, Excellent moisture resistance, High corrosion resistance, Superior weather resistance cover material, Low and high temperature toughness range -50° c to 121°c, Compatible with fmvss 116 dot 3, dot 4 and most non-petroleum based Brake fluids, Reasonable construction with three layer rubber and two braid pva reinforced. Brake hose assembly, hydraulic brake hose, hose end fitting, bracket, bundy tube, low carbon steel tube, copper tubing, rubber accessory, protector spring, tube nut , banjo bolt, locknut, copper washer, bleed screw, union, joiner, brake adapter fitting, air conditioning hose, power steering hoses and assembly, oil, fuel transmission hose, air brake hose Clutch hose, hydraulic clutch hose, flexible, motorcycle, automobile, automobile hose, motorcycle hose, brake tube hose, brake pipe hose, brake line hose, brake cable hose, dot, left brake hose, right brake hose, front brake hose, rear brake hose, sae j1401, fmvss 106, iso 3996, jis d2601, ntc 977, adr 7, ameca fmvss 106 dot, 3.2mmx10.5mm, 4.76mmx12.5mm, 1/8 hl brake hose, 3/16'' brake hose, brake hoses, clutch hose assembly, brake parts; hose, lincoln, buick, cadillac, jeep, ford, chrysler, chervole, gm, cherokee, dodge, rolls-royce, astonmartin, jaguar, land-rover, porsche, bmw, benz, opel, volkswagen, audi, renault, peugeot, citroen, volvo, saab, brake hose accessory, , fiat, toyota, lexus, honda, mitsubishi, mazda, daihatsu, nissan, subaru, ssangyong, daewoo, hyundai, kia, lada, tata
Water filling machine: The equipment is used in production of non-soda drink of mineral-pure water packed in polyester bottles. Washing, filling and capping are integrated in one machine. The most advanced technology from Japan and Germany is employed in the design. The gravity fixed liquid surface normal pressure filling is used. The filling is fast, the amount of liquid is accurately controlled and the dropping and leakage are avoided. Spring cramps are used in the bottle washing process. The empty bottles can be turned over 180~ along the conveying rail. There is once time of internal and external washing, the efficiency of bottle washing is high. The magnetic torque is used for screw capping. The power of screw capping can be adjusted without steps. The power of the screw capping can also be fixed, and the caps will not be damaged, the capping is reliable. The whole machine is controlled by PLC with touch-screen as the human-machine interface. The amount of the drinks in the storage tank can be controlled automatically. The filling and capping will be stopped automatically when there is no bottle. When bottles are cramped wrongly or when caps are not available, the machine can be stopped automatically. The frequency changing technology is used to adjust the operation speed steplessly. The production capacity can be displayed digitally and can be adjusted conveniently. Components: Washing- filling -capping system: 1 suit Value washing system: 1suit Empty bottle stop system when machine stop: 1 suit Bottle control system when machine stop: 1 suit UV sterilization lamp: 2 PCS Crawl device: 1 PC. Operation 1, Worker put bottles into bottle unscrambler; Unscrambler will bring bottles into 3 in 1 machine 2, Worker put caps into cap elevtor; Elevator bring caps into 3 in 1 machine. Electrical apparatus PLC/ transducer/ touch screen: Mitsubishi Contactor/ air switch/ stabilized voltage supply: Schneider Photoelectricity/ proximity switch: Autonics Cylinder: Airtack Motor: AB motor. Model YFCY12-12-4 Capacity(B/H) 3000-4000 Bottle size Neck:ö50-100mm Height:150-320mm Water pressure 0.18-0.25Mpa Water consumption(kg/h) 2000 Washing station 5 Dripping station 3 Filling precision +5MM Air pressure 0.4Mpa Air consumption 0.4m³/min Power(kw) 3.5 Weight(kg) 2000 Dimension(L*W*H) 2100*1600* 2100 mm.
Automatic Juice drink 3 in 1 hot filling machine: The equipment is used in production of non-soda drink of fruit juice, fruit wine, minerals and pure water packed in polyester bottles. Washing, filling and capping are integrated in one machine. The most advanced technology from Japan and Germany is employed in the design. The gravity fixed liquid surface filling is used. The filling is fast, the amount of liquid is accurately controlled and the dropping and leakage are avoided. Spring cramps are used in the bottle washing process. The empty bottles can be turned over 180~ along the conveying rail. There are two times of internal and external washing, the efficiency of bottle washing is high. The magnetic torque is used for screw capping. The power of screw capping can be adjusted without steps. The power of the screw capping can also be fixed, and the caps will not be damaged, the capping is reliable. The whole machine is controlled by PLC with touch-screen as the human-machine interface. The amount of the drinks in the storage tank can be controlled automatically. The filling and capping will be stopped automatically when there is no bottle. When bottles are cramped wrongly or when caps are not available, the machine can be stopped automatically. The frequency changing technology is used to adjust the operation speed steplessly. The production capacity can be displayed digitally and can be adjusted conveniently. Model YFRG12-12-4 YFRG18-18-6 YFRG24-24-8 YFRG32-32-10 YFRG40-40-12 ProductionB/H(600ml) 4000-5000 6000-8000 8000-12000 12000-15000 16000-20000 Bottle standard Neck:ö50-100mmHeight150-320mm Water pressure of washing bottle 0.18-0.25Mpa Water consumption for washing bottlekg/h 1300 2000 3000 4000 5000 Spraying position 4 7 10 14 18 Dripping bottle position 3 5 8 10 15 Filing precision +5MM Gas source pressure 0.4Mpa Gas consumption(m³/min) 0.3 0.4 0.5 0.7 0.8 Total powerkw 4.2 4.5 5 6.2 7.8 Total weightT 2 2.5 3 4 6 Dimension L*W*H)mm 2100*1600*2100 2500*1750*2100 2700*2100*2100 3500*2100*2100 3800*2200*2200.
1.Specifications Shaft Diameter 24mm Page Length 170mm Expanded Width 98mm Thickness 4mm 2.The specifications of doors fitted Length : 180mm-250mm Width : 70mm-120mm Thickness : 42-60mm Door type Door weight hinge needed Light 25kg A multi-functional hinge (plus a load-bearing hinge) General 45kg 2 multi-functional hinges Heavy 85kg 3 multi-functional hinges Over heavy 100kg 4 multi-functional hinges 3.Speeds in different interval Static interval (80¡ã-180¡ã) Quickly closing range Quickly-being closed interval (45¡ã-80¡ã) Quickly-being closed interval Quickly-being closed interval (15¡ã-45¡ã) For safety slowly-being closed interval Quickly-being closed interval (0¡ã-15¡ã) A little fast, competely being closed interval 4. Advantages 1) Technical performance: reliable and stable, durable working life, (50 million or more circles) 1)special-made aluminum, high quality steel or stainless steel, advanced hydraulic oil (pour point -45 degrees, flash point 190 degrees) used; imported spring and superior rubber seals (150+ degrees heat -resistant ) 2) strict scientific management, advanced processing technology ensure first-class quality. 3), for the parts from producing to finishing, high-precision testing equipments used, after series of strict testing, reliable and stable performance ensured. 2) Nice looking shape, no need of connection. 1), no connecting parts,. petite structure, elegant shape 2),Application of advanced technology , diversified color and style, better usage, better visual effect as well 3) Easy installations 1) No difference from normal hinge installation, simplicity, flexibility, easy operation. 2) no harm to the door, frame, wall and other home structure 4) High safety factor usage 1) unique function of shock absorbing. Max-guarantee human safety when door is slammed by outside large pressure. 2) due to the shock absorbing, make the door and door frame not destroyed ,meanwhile prolong the working life 5) Door closing speed can be adjusted control the closing speed by adjusting the bottom screws. Packing: One Unit Per Box, 20 Boxes Per Carton CTN Size: 42X32X42.5cm G.W. / N.W.: 22kgs / 20kgs The packing could also be customized according to your request.
his series testing machine is suitable for tensile, compression, bending, shearing, peeling and tearing test of metal and nonmetal materials, such as rubber, plastic, electrical wire and cable, composite, profiled bar, bar metal, board, spring, components and so on. It confirms to ISO 75001ú¼ASTM A370, ASTM E4 ASTM E8 and JIS, DIN, BSEN testing standards. AD800 in this machine is whole digit multi center closed loop measuring and control system. It adequately absorbs advanced functional characteristics and integrates the latest international professionally developed measuring and control system. Control software can automatically finger out routine data, such as tensile strength, yield strength, modulus of elasticity, extend rate after rupture, non-proportional extend strength RP0.2, etc. It can adopt many kinds of controlling modes, such as constant force, constant displacement, constant deformation, and real time display many testing curves of force-displacement, force-time, stress-strain. These curves automatically switch. Testing process control and data processing conform to the requirements of International standards. This machine is beautiful, multifunctional, safe and easy. Parameters: WDW-1 WDW-2 WDW-5 Maximum force: 1KN 2KN 5KN Accuracy: í_í+1% (0.5% as special order) Measuring range of force (KN): 0.2%--100%FS Resolution of force: 1/200000 of maximum force and no subsection of all scale Accuracy of displacement measuring: í+0.5% Resolution of displacement: 0.03ª¦m Speed adjusting range of displacement: 0.001-500mm/min Accuracy of deformation measuring: í+0.5% Range of deformation measuring: 2%í½100%FS Speed adjusting range of force; 0.005-5%F.S / S Speed controlling accuracy of force: ¿Qí+2.0% of the set value (speedú+0.05%FS/S) ¿Qí+0.5%/í+1.0% of the set value ( speed¿R0.05%FS/S) Speed adjusting range of deformation: 0.005-5%FS/S Speed controlling accuracy of deformation:¿Qí+2.0% of the set value (speedú+0.05%FS/S) ¿Q í+0.5% of the set value ( speed¿R0.05%FS/S) Valid tension testing space: 800 Compression testing space: 700 Clamping sample: Flat and round sample Power supply: 380V/220ú¼50/60Hz Working environment: Room temperature 10íµí½30íµ, relative humidityí_80% Base configuration : Panasonic servo motor, precision photoelectric encoder Weight(Kg): 300
SEM636 Wheel loader Main features 1, Engine: be reoptimized and rematched, improved efficiency and performance, improved cold start capacity. 2, Cooling: Designed by CRDC (Caterpillar China Research & Design Center), the cooling system brings end results of optimal cooling efficiency, increased fuel efficiency, less radiator plugging even under extreme hot temperature or dusty work environment. 3, Transmission: Countershaft design; advanced structure, high transmission efficiency; durable, ease of service and numerous shifts allow high travel speed; two modes available for multiple operation, one for material handling and one for travel; refined for heavy duty application. 4, Axle: Meritor axle, reliability function. 5, Cab: Improved operator comfort and visibility; Reduced in cab noise, meet GB standard, Reliability improved; integrated FOPs/ROPs cab is available. 6, Electrical: Large capacity Delphi battery; High quality electrical components. 7, Structure: Finite Element Analysis (FEA) design, refined for heavy duty application. 8, Hydraulic: VALVE [CCMC (Caterpillar China Machinery Component) components; Single lever, joystick controlling (optional)] HOSE [CCMC hose, improved strength and reliability, optimized hose and tube routing] Engine Model -------- XC6110/12G5-SG90 Rated speed ------- 2300rpm Rated power ------- 92kw Cylinder bore í+ stroke --------6í+110mmí+125mm Max. torque -------- 460n.m Displacement -------- 7.13L Transmission System Torque converter -------- 3-element, single stage Transmission ------- SEM TR-150 countershaft Gearshift -------Ѧ Ѧ Ѧ IV Forward -------7.4 13.7 25.3 41.5(km/h) Reverse ------- 9.3 30.5 Axle Four wheel drive, front axle fixed, rear axle oscillating, oscillating angle of rear axle+/-12 degree Hydraulic system Working pressure -------16.5MPa Boom lifting time ------- 4.82s Bucket dumping time -------- 1.07s Boom lowering time -------- 3.24s Brake system Service brake -------- Air assisted oil disc type four wheel brake Parking brake ------- Spring applied air released inner hoof type Steering system Pivoting angle of frame -------- 38 degree Load sensing hydraulic steering system Tank capacity Fuel tank ------- 151L Hydraulic tank ------- 138L Tire Size ------- 17.5-25 Main technical specification Operating weight ------- 9620kg Bucket capacity -------- 1.7m¬°/2.5 m¬° Breakout force ------- 128 KN Max. drawing force ------- 91KN Seaworthy
Features of the machine Because of the modular design of scroll and barrel, the model of thread, structure of barrel, draw ratio, feeding and exhaust data, conversion of network, the model of granulation, the electric equipment control mode can all be optimized and adjusted in the light of material system and the technological requirements. It is multifunctional as well as built for a special purpose. The machine is efficient with low specific energy consumption. The functional characteristics of TE series Bitruder include homoge neity, plastifying dying, fallibility, enhancement recovery and granulation. The host machine has modular design and the structure of screw and brrel are designed with precision by computer. It has perfect self purification and interchangeability. With planar triaxial reinforcement design and large safety capacity, new transmission torque dispensing equipment processes gear through high groove gear grinding. All the critical bearing is imported. The lubrication system is under interlock protection. The safe and reliable equipmene can stand wear and tear. Spiral shell's pole component of host computer connects with core axle and adopts the advanced involute spline to join the form. Change spiral shell pole association at will, in order to meeting different high polymer new material new technological requirements. The machine possesses various feeding structure and system. In accordance with different states of materials, the client may choose among single-scroll, twin-scrool, hollow spring engagement, nonengagement, forced side feeding and other modes. Fine vacuum exhaust and take off and wave device is effectively at to volatilize the composition supplies, Moisture and gas through releasing person who congeal the methods of vacuum discharge and shed, raise goods quality. In accordance with different technological rechirements, water cooing, oil cooling and qir cooling may be utilized. Various granulating systems, Air-cooling stick-drawing and particlecutting, air-cooling stick-drawing and particlecutting, aircooling rubbed thermal particlecutting, water-ring rubbed thermal particlecutting, off-centered spray thermal particlecutting and under rubbed thermal particlecutting. model Screw diameter (mm) Screw Rotary Speed (rpm) Motor Power(kw) L/D capacity (kg/h). TE-35 35.6 600 11-15 32-56 30-75 TE-50 51.4 500/600.
Type SH824 Model 4-Wheel Driving Dimension(mm) Length (including front loading) 4396 Width 2038 Height(to vent) 2810 Wheelbase(mm) 2195 Front-Wheel Tread(mm) 1610 Rear-Wheel Tread(mm) 1620-2020 The smallest ground gap(mm) 379 Radius to turning circle apply the brake without single side(m) 5.6 Structure mass(kg) Type with a cab 3750 Type without a cab 3500 The smallest using mass(kg) Type with a cab 3990 Type without a cab 3740 Mass distribution(kg) Front wheeltype with a cab 1640 Type without a cab 1600 Rear wheeltype with a cab 2350 Type without a cab 2140 Loading(kg) Front loading Max:310 Rear loading Max:480 Rated traction(KN) 19 Engine(Dongfanghong) Type 4108T82 Marked power(kw) 60.3 Shift number 8F+4R Speed range(km/h) 0.46-36.9 Transmission clutch Single piece,dry style,compaction with butterfly spring. Independently operating. Double action clutch Gearbox Main and assistant shifts both are mesh with straight teeth Rear bridge central transmission Screw prick gear Different speeder Close style, 4planet prick gears Different speed lock Mesh cover style Rear final transmission Single planet gear style,out-position with both sides of the back-bring box Front driving bridge front center transmission Screw prick gear Front different speeder Close style, 2 planet prick gears Front final transmission Single planet gear style Independent driving box Shift with column gear belt in straight teeth Front wheel table specification 11.2-24 Rear wheel table specification 16.9-34 Turning model Independent oil way, front-wheel turn with full liquiud pressure Running arrester Still liquid-pressure, tray-style, operate low-position pedal by man-power Parking arrester Handle operation,oil-bath style with multi-friction surface and machine compaction Control way of plough depth Place controling, Floating control place adjusting The strongest lift force of the system(KN) More than 16 Hanging device(mm) Three points back hanging Driving output axis(r/min) Postposition independent style 760/1000 (optional/540/1000) Traction device type Shift tow level, the place of the tow level can be adjusted
SUperior features of mobile screw air compressors Mobile diesel screw air compressors we manufacture have been offered to the use of industrial sectors dealing with a wide range of operations which are not fixed such as construction, mining and drilling. Designed at any flow rate and pressure you desire, mobile diesel screw air compressors take their places at both local and foreign markets which are safe for labor, high level operating capacity, highly efficient, with abundant replacement parts and a widespread network of service. With its case allowing access to every point of it, providing easy maintenance, mobile diesel screw air compressors with free air output ranging from 2m¦/minute to 26 m¦/minute can, if desired, meet pressure air requirements at different pressure and flow rate. > direct motor-compressor connection thanks to co-axial enupex coupling > fuel-tank with wide filler made of steel to get high resistance against corrosion (1 unit) > pneumatic control system manufactured by which adjusts motor speed depending on the air amount required , ensuring savings on fuel and improving output. > pressure lubrication line which ensures efficient lubrication > separator tank > high performance air-oil separator, ensuring optimum separation of air from oil. (1 unit) > oil filter with compressor by-pass. > air filter providing more efficient filtering of the air sucked by the screw group for big single-stage compressor part (1 unit) > single-stage air filter for the motor part (1 unit) > big fan, ensuring efficient operation of the unit even at excessive ambient temperature (1 unit) > integrated radiator for cooling compressor oil. > durable case designed in model style, painted with advanced technology painting techniques to ensure durability (powder point) > upper case making periodical maintenance possible and ensuring easy access to the iner parts of the machine. > no deformable and durable fenders. > ôsmart ignition systemö with efficient application of automatic start-stop function. > adjustable drawbar for easy connection to any vehicle. > parking system on the drawbar appropriate for motorways and spring-transmission braking system during driving. > adjustable front support ensuring operation during parking. > lifting lugs for ease of handling during transportation. > manual load-empty system for easy operation of the compressor. In the following cases, the compressor will automatically switch to protection mode: > high compressor temperature > high motor temperature > charging generator failure > oil pressure drop > electric ignition (24v or 12v system) > loading and discharge hook > drawbar.
High Torque Brusless Hub Motor : which is located within the rear wheel and drives magnetically with no brushes or gears to wear out or create noise. They are proven technology that operate with very high efficiency, has no wearing parts like gear and axle. The risk of mechanical failure in these parts are eliminited. Pivoting Rear Drive Wheel With Lock Spring : makes it one of, if not the easiest handling electric trolley on the market today. It provides exceptional handling, stability and manoeuvrability. Allows the buggy to be controlled with the very lightest of touches. Safe Start : prevents the motor from driving the buggy until the "start" button pressed, if the Freewalker is stationary when the power is switched on nothing will happen until the user presses the "start" button. Auto Disctance Control -TIMER : Press the "timer" button, your cart will proceed at the selected speed for the distance (15/30/45M) you have selected. Cruise Control : maintains the speed of the trolley irrespective of terrain, so you do not need to continually adjust the speed control dial of the buggy when going up or down hills to hold a constant speed. Descent Control :Setting the speed roller to minimum (i.e. fully towards you) can activate descent control. If the set speed of the Freewalker is too fast to negotiate a hill, engaging Descent control will then limit the speed of the trolley and allow for more control. Power Brake : is in addition to the descent control. The electronic brake can be utilized in the following ways; If the hill is very steep and requires additional braking, the brake button can be pressed once and again repeatedly in order to control the speed of the descent - or alternatively the brake button can simply be pressed on and the trolley will make its descent at a slow crawl. LOW BATTERY PROTECTION : protects the battery from damage as a result of being excessively discharged. The effect of this is that when the battery capacity drops 10% of the capacity left, the LED beside the "start" button will flash red and warn you to recharge the battery soon. Weight: 20.5 kg Buggy: 11.5kg, Battery: 9kg Dimensions: (mm) Unfolded: 105 (L) x 64 (W) X 100(H) Folded : 83 (L) x 64/34 (W) X 30 (H) Width (with/without wheels)
External configuration specification: Explanation: Special Type of Phone: Application Specification Model: KNSP-01 Defend grade: GB 4208-93 IP 66 Call capability of phone: GB/T 15279-94 Application scope: metro, light railroad, speedway, ship, mine, etc. External configuration specification: External dimension: 320f-205f-120mm Weight: 5.5Kg Installment dimension:139f-260mm M8 bolt is used to install 1. Upper cover 2. Sealing circle 3. Handset 4. Ring hole 5. Main body 6. Keyboard 7. Middle cover board 8. Logo (optional) 9. Cover spring 10. Connection soft tube for wiring Main features of product: 1f= Cabinet·ªaluminum alloy die·ícasting·+high anti-violent, able to glisten, convenient for looking for ( optional). 2f= Door cover·ªorient automatically and good self·íclosing·+convenient for use. 3f= Handset·ªmade of special engineering plastic·+high anti-knock resistancef=high tensile strength resistance and high anti-violent. 4f= All of the components including handset telephone receiver and transmitter·+keypad·+buzzer·+circuit board and cabinet are designed to be multi·ílayer waterproof and dust·íproof which is up to Class III grade. The whole machine is up to national standard GB4208-93 IP 66. 5f= Phone is provided with high stability·+high anti-jamming capability·+and it is up to national standard GB/T 15279-94. Main technical indexes·ª 1f= Applicable for various types of SPC exchange and dispatching exchange system with feeding voltage of 48-69V. 2f= Ambient temperature:-30f¦~60f¦ Relative humidity:10%~95% Atmospheric pressure: 86~106Kpa Circumstance noise:f_ 60dB·+A·¼ 3f= Sound level of ringing·ªfª70dB·+A·¼. 4f= Standard frequency·ªlow frequency group·ª697f=770f=852f=941Hz, high frequency group·ª1209f=1336f=1477Hz, frequency deviation·ªf_f+1.5% If service line is a 3Km signal·ílevel·ª Standard frequency·ªlow frequency group·ª-9dBf+3dB·+high frequency group·ª-7dBf+3dB·+level difference between low and high frequency of compound signal·ª2f+1dB·+the total distortion caused by intermodulation of harmonic wave is lower than the basic level by at least 20dB. 5f= Call transmission index·ª(5KM)SLRf_12,RLRf_-1,STMRfª10, output impedance is 600¬+. 6f= Super strong function is available for dialing 12 groups of numbers stored in the memory ·+maximum length of each number is16 digits·¼ External dimension: 320f-205f-120mm Weight: 5.5Kg Installment dimension:139f-260mm M8 bolt is used to install
Electronic weight indicator kit Compact and rugged instrument designed for any type of weight, force measurement application, to operate under any type of conditions. It is very simple to use and operate and is very user friendly. It is ideal for tabletop scales, weigh platforms, crane scales, conversion kits, weigh bridges, milk weigh bowls, tank-weighing systems, check weighers, packaging machines, bagging machines Apart from weighing related applications, it can also be used for force measurement applications such as in universal testing machines, spring testing machines, dynamometers, presses (mechanical, hydraulic or pneumatic) Its prominent features are - + Full software calibration + Provision for extra display + Provision for battery back-up + Provision for various options such as rs232 / rs485 output, printer output, two set points + Options of Class 2, 3, 4 or dual range General technical specifications: -Load cell excitation: ¦ 5V DC -Load cell drive capacity: 1 no. 350 W load cells (6 nos. optional) -Load cell connection: 4 wire or 6 wire -Input signal range: 0 to 30 mV -Sampling rate: 4 per second -Internal resolution: 40,000 counts -Display resolution: 1,000 to 15,000 counts -Accuracy class: Acc. To IS:9281 Class II, III, IV or dual range -Non- linearity: +/- 0.05 % of F.S. -Zero temperature co-efficient: +/- 0.01% RO/¦C/h -Span temperature co-efficient: +/- 0.01% RO/¦C/h -Drift of no-load output with temperature: +/- 0.05% -Drift of no-load output after 1 hour: +/- 0.15% -Drift of full scale output after 1 hour: +/- 0.01% Calibration: Full digital software calibration through keyboard (also possible through PC keyboard with MODbus protocol) Weight display: 5 digit 7 segment LED 12.7mm with negative sign Indications: Tare, Gross & Set points, through LEDs Keys: Micro keys (sealed membrane keyboard optional) Operating temperature range: 0 ¦C to +50 ¦C Storage temperature range: -10 ¦C to +70 ¦ C Operating voltage: 230 VAC +10%, 50 Hz (Optional - 110V AC, 12 VDC)
Description: Panel produced by mixing chipped wood with glue. Pressed with high pressure. Standard size: 48 ft (1220 2440 mm.) * Special size is available Thickness: 9 - 35 mm. Glue: E0, E1, and E2 Advantage: Less expensive, Strong screw holding, Light-Weight and Eco friendly Standard: FSC, CARB, EPA, EN, JIS, TIS and Green Lable
The panel is produced by mixing chipped wood with glue. Pressed with high pressure. Standard Size: 4x8 ft (1220 2440 mm.) *Special size is available Thickness: From 9 - 35 mm. Standard Thickness are 9,12,15,16,18,19,20,22,25,28,30,35 mm. Glue: E0, E1, and E2 Advantage: Less expensive, Strong screw holding, Light-Weight, Eco friendly There are Certificate FSC, EN, CARB, JIS A5908 and DIN 68761
Fiberboard is produced by mixing fiber (from wood) with glue. Pressed with high pressure. Standard Size: 4 x 8 ft (1220 x 2440 mm.) *Special size is available Thickness: 2.5 - 30 mm. Glue: E0, E1, and E2 Advantage: High-density fiberboards, Moisture Resistant, No Splinters, Smooth surface consistent, Easy to paint and cutting Standard: FSC, CARB, EPA, EN, JIS, TIS and Green Lable
