Model:728 Appearance:white Viscosity(cs):15000-17000 Hardness(shore a):26-28 Tensile strength (kgf/c o):35 Tear strength (kgf/ m):22 Elongation (%):470 Mixing ratio (%):2~3 Operating time(h):0.5 Curing time(h):2~4 32x32x46cm/durm 25kg/durm.
Molding silicone rubber, addition cure liquid silicone, pad printing silicone rubber, injection silicone rubber, electronic potting silicone rubbe 25kg/drum and 200kg/drum
Profile£ºyozho®2556££+10% part b is two-part high-temperature vulcanized silicone rubber, which can be made of excellent tear strength elastomer. s high transparency and brightness, stereoscopic, high and low temperature resistant, waterproof and resistant to aging, discoloration and other advantages Package£ºyozho®2556££has 5kg¡¢20kg package. B part has 0.5kg¡¢1kg package.
Dongguan tian'an silicone technology co.Ltd is an uprising chemical factory which specializes in manufacture all grades of silicone rubber which can be used for making keypads, mobile cases, utensils, gloves, nipples, o-rings, seals, gaskets, wires/cables, profiles and so on.Our price and quality are very competitive.Welcome to email to aileenshu at tn2008 dot com for price. 20kgs per carton
liquid silicone rubber: 1for statue molding, with good tensile&tear strength 2good operationbility 3resist to extrem temperature Liquid silicone rubber introduction: Applications of liquid silicone rubber liquid silicone rubber is intended for statue mold making ,candles. liquid silicone rubber is applicated for plastic toys, relieve furniture. liquid silicone rubber is used for architectural decoration, funiture decorative. liquid silicone rubber is application for sculpture, art crafts mold making, and so on. Features of liquid silicone rubber liquid silicone rubber for statue mold making is flowing liquid with general hardness of 22-50A¡ã after curing with features: 1. resistance to deformation and high-temperature, acid-alkali and expansion 2. good tensile strength, tear strength and elongation 3. high reproduction times. 25kg/drum.
Silicon rubber for mold making applications Silicon rubber for molding making is primarily intended for poly resin crafts, pu crafts, pu resin crafts , gypsum crafts , unsaturated resin crafts, lighting and candles crafts , plastic toy , stationery gifts crafts industry, a large statue buddha, relievo furniture, furniture decorative materials, statues buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils factory, europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on. Silicon rubber for mold making features Silicon rubber for mold making is white or red flowing liquid with general hardness of 22-50a++pafter curing. Molding silicon rubber is a kind elastic silicon rubber mold which features with resistance to deformation, high-temperature, acid-alkali and expansion as well as high reproduction times, good tensile strength , tear strength and elongation. Silicon rubber for mold making operations If the customer wants to make large products and large size molds, the mold should be made of silicon rubber with high hardness. On the contrary, if the mold with fine and precision patterns, it should be made of silicon with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If molds requiring fast drying and demould, more curing agent is needed; contrarily, if molds requiring slower drying and demould, less curing agent is needed. 25kg/drum, 200kg/drum
Introduction of rtv 2 molding silicone rubber: 1. Two-part of rtv 2 molding silicone rubber: flowable liquid silicon and catalyst. 2. Rtv 2 molding silicone rubber cures at room temperature within 4-6 hours. Features of rtv 2 molding silicone rubber: 1. Rtv 2 molding siliconerubber has an exceptional fluidity and good operability. 2. Rtv 2 molding silicone rubber hasgood temperature and deformation resistance as well as low shrinkage. 3. Rtv 2 molding siliconerubber has high duplication times. Operation step for rtv 2 molding silicone rubber: 1. Step one to use rtv 2molding silicone rubber: take 100g of part a and add 2g of part b and mix thesilicon rubber and the curing agent evenly. 2. Step two to use rtv 2molding silicone rubber: vacuum pumping 3. Without exception, thistakes less than 10 minutes. Otherwise, it will cause cross linking reaction, and no more further steps will be available. 4. Step three to use rtv 2molding silicone rubber: brushing cast & perfusion molding operation. 25kgs/drum vacuum package or 200kgs/drum
Contact: Amber hyja(at)szrl(dot).net Product Description Description of Food Grade Molding Silicone Rubber : Our RTV-2 Molding materials are general called two-component room temperature vulcanization liquid silicone rubber with excellent fluidity and good operational performance. Add part B into part A, stir the mixture evenly, then pour or brush the liquid mixture to the mother mold, then after 2-6 hours, a flexible silicone rubber mold will be obtained with resistance to deformation, high-temperature, acid and alkali and expansion. Applications of Food Grade Molding Silicone Rubber : Liquid food grade molding silicone rubber actually is a platinum catalyst silicone rubber which is totally non toxic, specially used for food molding, such as making silicone molds for confection, chocolate, jelly, sugar, candy, cake, cupcake, biscuit, cracker, icelolly, ice cream, ice sculpture, butter, fondant, bread, bakery, baking etc. Generally, silicone rubber food tray will be more popular since food such as chocolate and sugar are too small size, so our customers generally make silicone rubber tray, such as chocolate tray, sugar tray etc. Meanwhile, Food grade molding silicone rubber is also perfect for molding building decorations, arts and crafts, sculptures, furniture, manual mold design, shoe molding, tire molding, rapid prototype molding, foundry casting, lost wax casting, artificial jewelries molding and so on.
As directed by the FDA, the rubber materials used for extrusion should feature the following: No contaminants and no mixing should enter the food from the rubber seal that are in contact with the food items it should be free from all hazardous partical The material should be 100%detectable under metal scanners and x-rays. Since the western polyrub products experience rigorous wash downs with water sprays and abrasive chemicals, the plastic tends to disintegrate. Small fibers of the material enter the food products causing contamination. The FDA rubber used needs to be fabricated with a material that does not disintegrate in harsh circumstances. Utilization of western FDA-Approved Metal & X-Ray Detectable Rubber Materials by various Sealing Industry Materials used are authorized under FDA Title 21 CFR 177.2600.and ECC-1935.The materials shows magnetic properties. The approved materials are available in two variants: Silicone blue color and nitrile blue color
Transparent silicone rubber is specialize for crystal silicone mold, imitation zircon silicone mold,crystal resin diamond silicone mold, crystal facets diamond silicone mold, and polyester/ polyurethane/ epoxy section diamond silicone mold, rhinestone jewelry silicone mold, amber silicone mold, crystal jewelry silicone mold, imitation agate silicone molo, jade mold, jewelry rings silicone mold,boutique crafts molding and casting. Transparent silicone rubber Description Transparent silicone rubber is the best choice for diamond molding, crystal molding, resin crystal rhinestone molding. Transparent silicone rubber is suitable for flat dies and special three-dimensional mold plastic mold replication Transparent silicone rubber is the best choice of mold making material for complex shape and high-precision products molding & casting. Transparent silicone rubber Characteristics * Low shrinkage (less than 0.1% ) * High tensile and tear strength with high copy times * Hing heat resistance which can up to 250 °C * Easy for operation (mixing ratio at 1:1 /10:1) * Very good flow and easy for pouring operation * Fast and non-shrink cure at room temperature which can be accelerated considerably by the application of heat Transparent silicone rubber Technical Parameters Model HY-MJ2135 HY-MJ2235 Appearance Transparent High transparent Mix ratio 10:1 10:1 Viscosity (cps) 70000 70000 Pot life(hrs) >2-3h >2-3 h Curing time(°C/min) 100-120°C/30mins 100-120°C/30mins Density / g·cm-3 1.1 1.1 Hardness(A0) 35 35 Enlongation(%) ?¥280 ?¥320 Tear strength (KN·m-1)1518 Tensile strength (Mpa) ?¥4.8 ?¥5.2 Shrinkage (%) 0.1 0.1 (Note: the above data for this product in 25°C temperature, 55percent humidity conditions, for reference. The accurate data is measured by customers when using.)
1. Product Feature of Electronic Potting Silicone Rubber Electronic Potting Silicone Rubber is a kind of low viscosity, Inherent flame resistance, two components addition cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)PPABSPVC, etc. and metal materials. 2. Typical Application of Electronic Potting Silicone Rubber HY-9055 electronic potting silicone rubber could be applied to - high powered electronics, - DC/DC module and circuit board which requires heat dissipation and high temperature resistance. -It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc. 3. Technical Guidelines of of Electronic Potting Silicone Rubber a, Pls put part A and part B in separate container and stir evenly before mixing the two part together. b, Mixing Ratio: part A: part B = 1:1 c, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring. Note: The thickness of the silicone affects the curing time. If the silicone used is a little thick,then the curing time will be a little longer.The temperature also affects the curing time.When in lower temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization. With temperature of 80ï½?100, the silicone will cure in 15 minutes; while in 25 room temperature, the silicone will cure around 8 hours. 4.Notes of Electronic Potting Silicone Rubber a.The following material may hinder the curing of HY-9055, So pls use after the test. When necessary, pls clean the application areas. Organotin compound or Condensation silicone with organotin Sulphur, sulfide and sulfur rubber materials. Amine compounds as well as contains the amine materials. Pewters solder flux b. HY-9055 should be sealed storage.The mixture should be used up disposably to avoid causing waste. c. HY-9055 belongs to non-dangerous goods, but keep away from mouth and eyes. d. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance
Product Feature of Electronic Potting Silicone Rubber HY-9055 silicone rubber is a kind of low viscosity, Inherent flame resistance, two components addtion cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time. It can be applied to electronic components for insulation, waterproofing, fixed and flame retardant. It mainly applied in electronic components surface with materials of PC(Poly-carbonate)PP ABS PVC, etc. and metal materials. 2. Typical Application of Electronic Potting Silicone Rubber HY-9055 electronic potting silicone rubber could be applied to - high powered electronics, - DC/DC module and circuit board which requires heat dissipation and high temperature resistance. -It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc. 3. Technical Guidelines of of Electronic Potting Silicone Rubber a, Pls put part A and part B in separate container and stir evenly before mixing the two part together. b, Mixing Ratio: part A: part B = 1:1 c, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring. Note: The thickness of the silicone affects the curing time. If the silicone used is a little thick,then the curing time will be a little longer.The temperature also affects the curing time.When in lower temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization. With temperature of 80?100?, the silicone will cure in 15 minutes; while in 25? room temperature, the silicone will cure around 8 hours.
The pad printing silicon rubber is a carrier which transfers the patterns from the steel plate onto the products' surface. The pad printing silicon rubber has the advantages of good printing effects,good quality,good resilience and without any impurity. Pad printing silicon rubber is mainly applicable to the printing of irregular patterns on plastics toys,electronplating products,electronic toys, trademarks,artwork gifts ,stationeries etc. Applications of liquid pad printing silicone rubber Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers . Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface. 2. Features of liquid pad printing silicone rubber a. resistance to deformation, high-temperature b. high printing times c. good aging resistance d. exceptional elasticity e. great printing effect 3. Operation Instructions of liquid pad printing silicone rubber Pad printing silicone rubber is two-component silicone, part A is liquid silicon rubber, part B is catalyst. The usual mixture of silicone rubber and catalyst is 100: 2 or 100: 3. E.g. we take 100g of liquid silicon rubber and 2g-3g catalyst, mix them and pour it to your mold. A fter 2-4 hours, you will get a Pad printing silicone rubber. HY-918 with the advantages of high temperature resistance, abrasion resistance,Â good printing effect, etc.Â , which made of top-quality raw material due to adding American Dupont Teflon high-temperature resistance new material, is processed through high-temperature machining. The product is mainly applicable to plastics toys, electroplating products, electronic toys,Â trademarks and irregular pattern printing. The silicon pad is a carrier which transfer printing the patterns onÂ the steel plate onto the toy products' surface. HY-918 is a kind of silicone rubber to make the printing pads for plastic toys, craft works, product printing. Characteristics good printing effects good quality good resilience and without any impurity.
Factory price rtv2 silicone rubber for crafts molding Crafts Molding Silicone 1.Description 2. Technical Datasheet Typical general characteristics Inspection MethodValue Product data (Catalyzed A+B)C-820C-825 HardnessShore A20±225±2 Mix RatioA:B100:3100:3 Color/WhiteWhite Pot life25 °C (77F)30-40mins30-40mins Curing time25 °C (77F)3-4 hours3-4 hours Mixed viscositymPa.s16000±100020000±1000 Tear-strengthkg/cm20±222±2 Tensile-strengthM.pa3.6±0.54.0±0.5 Elongation%400±50450±50 Shrinkage%?¤0.3?¤0.3 Note: This is a 100A:3B mix ratio product that must be measured by weight. The choosing of suitable hardness should be according to the size and pattern design of the products. If large products and therefore multiple-piece molds are needed by customers, silicone rubber with higher hardness will be required for the molds. Conversely, soft silicon is indispensable for molds with complicated pattern and delicate details. The amount of curing agent admixture depends on the actual need of customers. More will be added for speedy drying and fast release and less when otherwise. 3. FEATURES Low viscosity,great flexibility,Extra low shrinkage,Chemical resistance,release properties, Easy to work with,High tear strength,Heat Resistance,various color is available,High reproduction rate 4.SHELF LIFE: When stored at or below 32°C (89.6°F) in the original unopened containers, C-8 series Silicone Base and its Curing Agents have a usable life of I0 months. 5.Package Silicone base:1kg/drum; 20kg/drum;25kg/drum;200kg/drum. Curing Agent: 30g/bottle; 1kg/bottle
Silicon rubber cloth Silicon rubber cloth is made of high-temperature resistant, corrosion resistant and high strength glass fiber cloth which is rolled or soaked with organic silicon rubber. The silicon rubber coated glass fiber cloth includes two types of single side and double sides. Compared with the common coated fabrics, the silicon rubber coated glass fiber cloth is characterized by unique high-temperature resistance, permeability resistance, excellent weather aging resistance, softness and toughness. The silicon rubber coated glass fiber cloth is a new composite material-made product with high performance and multiple functions. The silicon rubber cloth can be used in fire proof curtain and fire proof blanket, but not places where is containing sio2 flue gas and vapor exists
Model530 Colorwhite Mixing ratio (%)2% Pot life (mins, under 2530-40 Curing time(hrs, under 25)3-4 Hardness ( shore a )30±2 Tensile-strength (mpa)4.2 Tear-strength (kn/m)26±2 Viscosityafter a/b mixed , mpa.S27000±2000 Shrinkage rate (%0.2% Elongation450
Making molds for gypsum, grc, concrete, resin products etc Artificial stone products molding, wax casting Decoration building mold making (cornice, column, balustrade, ceiling, pedestals, fountains, mantels, wall ornament, planter, furniture decorative etc.) Unsaturated rein crafts, epoxy resin crafts, poly resin crafts, polyester resin. Lighting & candles crafts, stationery gifts, crafts industry Casting for statue, buddha, christmas ornaments, sculptures, figures etc -