The Apollo touch screen room thermostat is mainly applied the Heat pump, Gas Heating, Electric Heating, and so on systems. Features: 24VAC or Battery Powered (2 x AAA) Large Backlit LCD Touch Screen Security Logic inc Key lock & Limit Control 7 day, 5+2 Day or Manual Operation Programmable Fan Logic Heat cool & Heat Pump Logic Single & Multistage Control Remote Sensor Inputs Outside Sensor Inputs Designed and built by Smart Temp Australia Comprehensive 3 year Warranty RTB Specifications: Input Voltage (Hardwired) 20-30 VAC 50/60 Hz Relay Rating 24 VAC @ 1 Amp Max Per Relay Battery Power (2) AAA 1.5 V Operating Temperature 0° C to 55° C Operating Relative Humidity 0-95% (non-condensing) Storage Temperature 0° C to 65° C Size: 125" W x 85" H x 25" D (mm) LCD Display Size 57 W x 99 H (mm) Back Light White LED Short-Cycle Delay Off or 4 minutes Displayed Temperature Resolution 0.1° C Set Point Range Heating 5° C - 49° C Cooling 6° C - 50° C Heating and Cooling Limits Fully adjustable Onboard Sensor NTC type 3 100K Remote NTC type 3 10K Warranty 3 years (RTB).
BF-630 is one of CHIYU Technology's Fingerprint, single door access controller with Web Bbased. Ideally, BF-630 is used to manage entrance security or a small office as a simple time attendance recorder with Fingerprint or RFID and Password. IP Based with embedded Web Server Optical based fingerprint sensor Lower power consumption, OSD menu (On Screen Displayer) Voice indication module option Fire Alarm/ Door Sensor USB device option (for logs extraction) Double Badges and Interlocking Anti Pass Back unlimited levels Fingerprint + Pin/ Card + Password/ Lock Release/ Exit button Time zones 50 Holidays/ 40 Function Keys/ 32 Departments,Designations, Groups 64 Time Sets and Time Zone ► Technical Specification Verification Option Fingerprint Fingerprint + Card Fingerprint + Pin Card + Pin Fingerprint + Card + Pin Verification Mode 1:1 /1:N Verification Time Less than 2.0 sec Registration Time Less than 3.0 sec Capacity 950 persons, totally 1900 templates (2 templates/ Users) Log Data 32,768 System Log 2,000 Relay Output 2 Reset Button 1 Sensor Input 1 Communication Interface RS-485×1 →Relay Box (BF-20/ BF-50) TCP/IP (Reserved for internetworking) WG In & Out 26/ 34 bit Communication speed Ethernet 10/100M, Auto crossing Card format 125 KHz (EM/TM) 13.56 MHz Reading Range 7 ~ 12cm (EM/TM) 3 ~ 5 cm (Mifare) Language Traditional/ Simple Chinese/ English Keypad 10 numeric keys (0~9) + 6 function keys (F1~F4,#,*) & 1 Door Bell Display 128 × 64 Dots LCD Operation Temperature 0℃~ 65℃ Operation Humidity 5% ~ 95%RH Dimension 125 × 145 × 33 mm Weight 360 g.
Detailed product description 1. Power meter measures voltage, current, power, power factor, kwh, kvarh 2. Rs485/ modbus 3. Power quality analysis 4. Di/do PMAC735 power meter features: 1. Suit for lv/ hv voltage system 2. Compact design with all real-time measurement 3. Consist of basic unit and optional modules 4. 10 years back-up of integrated energy data 5. Large lcd, high brightness, auto-scrolling 6. High accuracy, v or i is 0.2%, kwh is class 1 7. Ct and pt programmable 8. Pluggable terminals, easy to install 9. Panel size: 96 x 96mm 10. Password protect PMAC735 power meter basic function: Provide one rs485 communication, measures and display real-time parameters: 1. Voltage¡ªua, ub, uc, uab, ubc, uca, 2. Current¡ªia, ib, ic, in 3. Active power ¨c pa, pb, pc, p 4. Reactive power ¨cqa, qb, qc, q 5. Apparent power¡ªsa, sb, sc, s 6. Power factor¡ªpfa, pfb, pfc, pf 7. Frequency 8. Active energy¡ªkwh (4 quadrant) 9. Reactive energy¨c kvarh (4 quadrant) 10. Demand and max. Record for i, p, q, s 11. Unbalance rate for u, i 12. Max./ min. Value Pmac735 power meter di/ do modules: 1. 4 status input + 4 relay output 2. 8 status input + 2 relay output 3. 8 status input + 2 pulse output 4. Profibus communication module Pmac735 power meter optional function: 1. Up to 31st harmonic analysis, k factor, thd 2. Soe (event log) 3. One 4~20ma analog output. Pilot's packing; neutral packing; customized packing.
Cube2--c17200 (cda 172) beryllium copper is the most commonly utilized copper beryllium alloy and is notable for its highest strength and hardness compared to commercial copper alloys. C17200 alloy contains appr. 2% of beryllium and achieves its ultimate tensile strength can exceed 200 ksi, while the hardness approaches rockwell c45. Meanwhile, the electrical conductivity is a minimum of 22% iacs in the fully aged condition.C17200 also exhibits exceptional resistance to stress relaxation at elevated temperatures. Typical application for c17200 beryllium copper alloys: Electrical industry: electrical switch and relay blades, fuse clips, switch parts, relay parts, connectors, spring connectors, contact bridges, belleville washers, navigational instruments, clips Fasteners: washers, fasteners, lock washers, retaining rings, roll pins, screws, bolts Industrial: pumps, springs, electrochemical, shafts, non sparking safety tools, flexible metal hose, housings for instruments, bearings, bushings, valve seats, valve stems, diaphragms, springs, welding equipment, rolling mill parts, spline shafts, pump parts, valves, bourdon tubes, wear plates on heavy equipment, bellows Available sizes: Custom diameter & sizes, random mill lengths Available products (forms): Round bars, round strips, round wires, round tube, Flat bars, square bars, rectangular bars, hexagon bars, plates, sheets, coils Custom shapes are available upon request. Wooden cases
Features ADSL Connection Speed up to 24Mbps Downstream ADSL, DASL2/2+, RE-ADSL Support Compatible with all major DSLAMs Multiple PVC up to 8 support USB Plug-and-Play installation ADSL Features RADSL (ANSI T1.413 Issue 2) G.dmt ADSL over POTS G.992.1 Annex A) G.lite (G.992.2) G.hs (G.994.1) Auto-negotiating rate adaptation ADSL2 G.dmt.bis (G.992.3) ADSL2 G.lite.bis (G.992.4) ADSL2+ (G.992.5) Protocol Support ANSI T1.413 issue 2 ITU-T G.992.1, G992.2, G994.1 RFC 1483/2684 (Bridged/Routed Ethernet over ATM) USB support PPP over ATM (RFC 2364) USB support PPP over Ethernet (RFC 2516) ITU-T 1.610 F4-F5 OAM Send and Receive/Loop back Transparent Bridge Support PAP/CHAP/MS-CHAP for password authentication support DHCP Server/Relay/Client DNS Relay Agent DMZ Support PPP Always on with configurable timeout Connector One USB port with specification v1.1 compliant One Ethernet 10/100Mbps Base-T One RJ-11 port for ADSL connection USB Cable Power Jack Compliance Certificates FCC Part 15, Part 68 CE Mark Management Support Web-base Configuration GUI Command-line interpreter (CLI) Telnet Remote Management FTP/TFTP firmware upgrade and configuration backup/restore Syslog Support Security NAT for Basic Firewall Support Packet Filtering Firewall Support Stateful Packet Inspection Support Protection against Denial of Service attacks Password Authentication to Modem Environmental Operating Temperature: 0ípC ~ 50ípC Humidity: 5% ~ 95% (non-condensing) Storage Temperature: -40ípC ~ 70ípC 575*40*24,10KG
1.Adopt 16 single chip micyoco digital automation automation control 2.The mode of connection is three input and six output, all series on line protaction will come ture. 3.The main component is from japan and the brand of cpu is philip. 4.Based on the different load we can set different current and voltage time of start torque , then we can get the best current pulse and the characteristic of the torque. 5.It can provide motor slip start progress, reduce the starting current on the impact of power grid. Reducing vibration and noise of equipment . Extended the life span of mechanical transmission, and improved working environment for artificial. 6.Starting current can be adjusted based on different load. Reduce the loss of start and to get the best torque based on the smallest current. 7.Has different kinds of protection, such as over current , over load and lin input phase loss, to insure the safety of the equipment and motor. 8.Theyí»doutput of the soft-start will be increased based on the setting the law, so controlled in accordance with the superior optimization of motor speed up the curve to complete the boot process. 9.A convenient external control interface has multi-function: digital delay start control, soft stop control input, start delay relay output, fault relay output. 10.Automatic identification of phase sequence and phase sequence protection with themselves
Cabinet air conditioner supplier, cabinet air conditioner, cabinet air cooler, panel air conditioner, tec air conditioner, thermoelectrical air conditioner, peltier air conditioner, peltier cooler, cabinet air cooling, industrial air conditioner, outdoor air conditioner, heat exchanger, telecom heat exchanger, dehumidifier, semiconductor dehumidifier, cross flow cooling fan, protection relay, digital meters, temperature controller.
Injection moulded plastic automotive components like mak cover, gear wheel, stay, bowl upper, head lamp relay, tray battery, end cap, brass pipe, dust cover, jack cap, jack pin, terminal case white, housing cover, gasket electric, base cover, garnish bracket, gasket electric, glass holder, bobbin flange, connectors, cb belt clips, ktr cover, connecting covers, pannel tray, connectors, terminal covers, square boards.Transportation
Product introduction This series of battery management system mainly used in lithium battery powered electric vehicles, electric boats, and electric equipment. Real time monitoring of the cells voltage, the total voltage of the battery pack, the temperature of the cells, the charge and discharge current. Provide the cells balance management, charge and discharge control, heating and cooling management, and fault information alarm.The system can be connected to the computer through the rs485 interface, and the operating parameters of the system can be monitored and configured by the matching computer software. The basic control strategy (1) after power on by the switch, in the case of the battery system is operating normally, both the charge and discharge relays will be closed. (2) when the battery pack and cell over charge protect voltage occurs, disconnect the charging relay, until reached the release voltage. (3) when the battery pack and cell over discharge protect voltage occurs, disconnect the discharge relay, until reached the release voltage. (4) when the charge over and under temperature protect occurs, disconnect the charging relay, until reached the release temperatur (5) when the discharge over and under temperature protect occurs, disconnect the discharge relay, until reached the release temperature. (6) when the charging over current protect occurs, disconnect the charging relay, it will not be released until next powered on. (7) when the discharge over current protect occurs, disconnect the discharge relay, it will not be released until next powered on. -
QN-Kit06 Outdoor Receiver 2 Channel Rolling Code and Fixed Code Garage Door Gate Receiver Feature 1.2-Channel or 4-Channel independent set-up ; remote control unit ; 2. Can learn up to 149 codes; (can be customized); 3. Costomized frequency such as 433.92Mhz, 315Mhz ,868Mhz ; 4. Power supply : 9V-24V DC/AC ;control unit; 5. Relay Spec.: 12A 14VDC or 7A 120VAC ; 6. CE proved ; 7. Outdoor usage, waterproof; 8. Working range: 100m Usage 1. For garage door use remote control unit; 2. Wireless working within 100m (can be customzied); Model No.: QN-Kit06 Power supply: 9-24V DC/AC Measure Type: Fixed Code & Rolling Code Relay spec: 12A 14VDC or 7A 120VAC Operating distance: 100m Gurantee: 1 Years Modulation: Ook/Ask/Fsk Application: : garage door opener,alarming system,security system,vehicles etc HS Code: 85269200 Power Adapter: Yes MOQ: 500 CE: Yes
The equipment has the function of automatic control by pid controlling vulcanizing tank of curing temperature, curing pressure and curing time to guarantee the quality of tyre vulcanizing, such as temperature compensation, automatic alarm, automatic timing.Use temperature relay, to effectively control of temperature, error within 1.2℃.The adoptwing valve to control, the overpressure automatic exhaust.Time control with the time relay to set precise vulcanization time.With the functions of vacuum pump vacuuming. Vulcanizing tank gas tubes (hose) made of materials with high temperature and pressure resistance .The thickness of the steel plate, 10 mm, can take the pressure of 10 kg.Using packing seal, characterising the high temperature resistance, not easy to heat, ensure the seal well. Voltage: 380v/50hz Power(w): 55kw Dimension(l*w*h): 4300*2300*2300mm Weight: 3200kg Certification: iso After-sales service provided: engineers available to service machinery overseas Color: blue Working pressure: 0.8/mpa Standard rim diameter: 15''-22.5'' Dimension(l*w*h): 4300*2300*2300mm Weight: 3200kg
Introduction Automatic calibration function, the panel error correction, simple and quick operation, ensuring more accurate; Four double-color digital display; Two relay alarm, power protection, safe and reliable; More than 20,000 hours trouble-free operation; The perfect combination of triple anti-jamming technology to ensure system stability; Available in a variety of voltage (for example, 0 ~ 10V) or current (for example, 4 ~ 20mA) linear output signal; Complete specifications, compatible with a variety of pressure input signal; Can provide the same point pressure / temperature measurement dual display dual function, support for multiple thermocouple input E-, J-, K-, S-type. (For PS48 only) Order Format Format :PS Model--Rang Code--Power Code--Output Code--Alarm Code--Input Code--Shape Code--Temperature e.g:PS4810-035-225-311-433 Product Model"PS4810",Intelligent Pressure Indicator Pressure Rang Code"035",The pressure rang is 0~35"MPa; Output Signal Code"225",Two-Way signal output 4-20mA and 1~5V; Alarm Methods Code"311",Adopts 2-way relay top and bottom limitation alarm; Input Signa Code"433",Mating for the transducer that has 3.33mV/V output; Vacancies and not marked function codes are the default values.
Basic parameters Size460 mm * 300 mm * 150 mm Weight: about 7 kg Working voltage: ac220v 10% 50 hz Output voltage: dc24v The number of channels: 1 - 16 Digital tube display mode: highlight inspection display mode Signal input: rs485 bus transmitter Communication interface:(optional) 1 road rs232 and rs485 bus interface Standard mod bus rtu protocol or non-standard, can connect the computer monitor Measurement range: 0-9999 (can be set ) Alarm way: first alarm more than 90 db alarm way; Second alarm more than 120 db Control output: 8 channel relay ou tput, Distribution channel address, 1 bus relay output Temperature range: - 10 ~ 50 Humidity: 15% ~ 70% rh (no condensation) Execution standard: the combustible gas alarm controller gb16808-1997 technical requirements and test methods Installation method: wall-mounted installation
The M160T Ethernet Remote I/O module provides 8 optical-isolated digital inputs, supports max. 10Mhz high speed pulse counter, 8 isolated 12bits analog inputs, supports 0~5V, 0~10V, 4~20mA, 0~20mA analog signal, 8 digital outputs, supports 10Hz~300Khz high speed pulse output or relay outputs. All of the I/O with high sampling frequency and special filtering strategy to ensure its reliable. It is design for working in the harsh industrial application environment, widely used in a variety of industrial automation, security monitoring system, automatically measurement and control system.
ML14xx is Multiload Monitor with 12 single phase load or 4 three phase load option. It measures important electrical parameters of multiple loads simultaneously in a single unit, eliminating the need and cost of multiple panel meters. It provides quick, easy and error free current connections with plug and play connectors. It measures real time electrical parameters like Active / Reactive / Apparent energy and power, current, THD, demand, max demand for each load. The instrument has 4 configurable relay outputs, which can be used for Limit / Pulse / Residual Current / 3Phase Load Health Monitoring / Tariff / RTC / Timer tripping or alarms. This instrument communicates with either MODBUS or Ethernet connection
The S2-EM is a compact, waterproof stand-alone programmable access control system. The product unique feature is simple in design, easy operation, and high reliability. Main Feature > Waterproof, conforms to IP66 > One relay, 2000 users, standalone > Card type: 125KHz EM card only > Working temperature: -40 oC ~ 60 oC (-40 oF ~ 140 oF) > Pulse mode, toggle mode > Built in LDR for anti tamper > Card block enrolment > Easy for programming by master cards and remote control > Easy for install, 6 wires only
Description The ddsy1088 single phase keypad energy meter measures total active energy.It is STS certified. and complies with the standards of IEC62052-11, IEC62053-21, IEC62055-41 &IEC62056-21.BS standard complied. It can be inserted the plug-in communication module to achive the AMR/AMI solution.And with built-in relay,it can be remote control. Function 1.Easily configurable Prepaid & Postpaid mode by token 2. Anti-tamper 3. Load profile 4. Exchangeable, optional communication module:GPRS/3/4G/PLC/GSM/Ethernet 5.Real time measures voltage, current, frequency, active power, etc 6.Open Protocol: DLMS/COSEM 7.Programable multi-tarrif
Stand-combustible Gas Detector BJ-92-1A-11 Combustible Gas Detector Detection of gas: 1A: natural gas BJ-92-1A-11 Combustible Gas Detector Output: * DC12V pulse output * AC220V contact output * AC220V pulse output * AC220V Output * Relay contact (normally open output), with the controller BJ-92-1A-11 Combustible Gas Detector Technical Parameters * Detection of gas: natural gas * Detection method: FIGARO semiconductor gas sensor * Alarm concentration: Gas explosion limit below 25% * Power supply: AC220V 15% * Power consumption: 3W or less * Temperature: -10 ~ 55'C
Machine feature: The machine uses 16 control chip, simple parameter setting , with high quality steel desktop design, operation more convenient.Coil parameter can be setting by section, winding by manual, can follow one, s inclinations of the winding. Application range: Suitable for small transformers, relays, power converters, communications coil meter coils, fans of the stator coils. Specifications Spindle number1 Wire size range0.06-1.2mm Loop diamete200mm Winder widthhand row Max speeda:1500turn/min B:3800turn/min Input powerac 120w Input power220v50hz/60hz Machine size43030000mm Package size450560310mm Net weight37kg Gross weight45kg -
The sd series optical level switch uses the principle of light reflection in a prism to sense the absence or presence of a liquid at the point where the sensor is installed in a tank, pipeline or other type of container. Feature: 1.Simple and compact with no moving parts 2.Led indication 3.10-28vdc, 115vac or 230vac powered versions 4.Solidstate npn/pnp or relay output 5.Operating temperatures up to 257°f (125°c) 6.Wide range of use in machine systems for a variety of liquid level detection 7.Unique sd22 design, switch body and tip disconnects