Essco Industrial furnace For metallurgical heat treatment such as hardening, annealing, carborising, tempering Types of furnaces Box type Bogie hearth type Conveyor type Bell type Pit type
Hunan Baling Furnace Energy Conservation Co.,Ltd(Baling Energy, stock code:831054)is established in Nov.1998, as a professional high-tech manufacture engaged in R&D designing, manufacturing and servicing for industrial energy-saving furnace equipments. The main products include no bypass unpaired reversible regenerative combustion type furnaces, rotary regenerative air pre-heater, silicon carbide metal combination air pre-heater, blower and induced draft fan for combustion system etc., which are used widely for non-ferrous metal, machinery, building material, ceramic, steel, petrochemical and similar industries. www.blenergy.cn
BL Energy Industrial smelting furnace Application range : 1350degree regenerative series application Aluminum and other non ferrous metal smelting furnace Steel furnace, heat treatment furnace Temperature refractories, ceramics, sintering brick kiln 1650degrees regenerative series application Copper, steel, iron and other high temperature furnace Refractories, ceramics and other high-temperature sintering furnace Glass, building materials and other high temperature furnace Product Features Technical specification 1). Temperature efficiency: 90%,maximum as 93% 2). Total recovery rate of flue gas: 90%,maximum as 92% 3). Comparison with non energy saving furnace: 1350degrees Series energy saving rate : 40% to 60% 1650degrees Series energy saving rate : 50%to70% 4). Comparison with traditional paired regenerative combustion technology, the energy saving rate: 20%to30%
Andalusite brick contain Al2O3 more than 48%, which is made of high grade bauxite through high temperature calcinations. Its refractories is usually above 1770 Â°C. The main mineral components are corundum and mullite phases. It is a kind of neutral refractory material so that it enjoys excellent resistance to acid and alkali corrosion. According to Al2O3 content,it can be divided into three degrees:The Al2O3 content is more than 75%.The Al2O3 content range from 60% to 75%.The Al2O3 content range from 48% to 60%.
Features: it(av) 2472a Interdigitated amplifying gates vdrm/vrrm 1900-2500v Fast turn-on and high di/dt tq 35~70us Low switching losses itsm 27ka I2t 3645103a2s Typical applications: Inductive heating Electronic welders Self-commutated inverters
Magnesia chrome brick is an alkaline refractory product, which is made of periclase and magnesia chrome spinel, and is fired at 1600~1800 °C in an oxidizing atmosphere. It can also be made into non-burned brick by chemical bonding agent such as water glass. According to the raw materials and process characteristics of the products, it can be divided into silicate-bonded magnesia-chrome bricks, direct-bonded magnesia-chromium bricks, re-combined magnesia-chrome bricks, semi-recombined magnesia-chrome bricks, pre-reacted magnesia-chrome bricks Casting magnesia chrome bricks.
By plane; By within door. Stable s pond your requests within 8-working-hour. Gross weight:about 1 ton Cbm:around 3cbm
Submerged arc furnace¡ait¡¡¥s also known as electric arc furnace or resistance electric furnace. It is mainly used to reducing smelting ore, carbonaceous reducing agent and solvent etc. Mainly adapts to production of ferrosilicon, ferromanganese, ferrochrome, ferrotungsten, silicon manganese alloy and other ferrous alloys, it is an important smelting furnace in metallurgical industry for production of industrial raw materials and calcium carbide and so on chemical raw materials. The working character is to use carbon or magnesia refractory materials as furnace lining, use self roasting electrode. Electrode inserts into the materials inside the furnace for submerged arc operation, using arc energy and current through the materials, and due to the resistance of the materials and produce energy to melt metal. It¡¡¥s a kind of industrial furnace which is worked continuously, charged material in succession, and tapped out metal or slag in intermittent. Capacity:3000kva-33000kva, smelting different ferroalloy by ores.
This equipment combined the functions of aluminum bar sawing bench and heating furnace, which can complete relevant operations concurrently. It's energy saving and short working time.
This machine combined the function of aluminum bar sawing bench and aluminum bar heating furnace, which can complete relevant operations concurrently. Heating type:gas burning inside there is hot air insulation material filled in the furnace wall,flame heating on the surface of the workpiece direct so that absorbing more heat. Just only need 20 mins from normal temperature to the operating temperature. Equip to independent nozzle. The material rack adopts automatic feeding and recharging mode for labors saving.
This equipment is mainly used to the final hardening treatment to the finished aluminum profile .There are single-door, double-door, skip manual skip maneuvering mode and so on. Heating type is oil burning, gas burning, and electric heating. It is mainly used to aluminum profile aging , as well as drying and sintering at the same max temperature is 260 degree.
1. High-quality heat source Under common-pressure liquid, the oil transfer heating system can output hot oil of maximum 350 fª for the heat user; Our heat-conducting oil heating systems applied the Fuji temperature control instrument and the intelligent self-tuning temperature control technology. The control precision is about f+ 1 fª and accurately control in the range of the used temperature; the main power for the heating used the solid-state modules non-contact switch circuit in order to adapt to the frequent switching and have no interference to the power supply. Dry combustion can also be avoided. The hot oil cooling system can be designed according to the end userf+s requirement, so that it can satisfy the process requirement of rapid cooling after heating up; 2. To save energy and low operating costs Heat-conducting oil heating system is the liquid phase closed cycle. The temperature difference between the output oil temperature and the return oil temperature is 20-30 fª, that is only to heat a temperature difference of 20-30 fª can the working temperature be reached. Meanwhile, no water treatment equipment is required for this device. No lose of steam runningf= steam reekingf=steam dropping and steam leakage as the steam boiler. The utilization ratio of heat is very high. It can save about 30% energy compared with the steam boiler. 3. Low Equipment Investment Due to the reason that the system of the heat-conducting is simplef=no water treatment equipment and more auxiliary equipmentf=low pressure bore by the boilers etc., the investment for the whole system is comparatively low; 4. Safety Because the system only withstands the pump pressure and there is no explosion risk for the heat conduction oil heating system, it is more secured; 5. Environmental Protection The environmental effect of the organic heat carrier heating system is mainly reflected in the minimal fume emissions, no sewage pollution and no thermal pollution; 6. Widely Application It can be applied in the following areas: by high-temperature shapingf= plate heatingf= rubberf= dryingf= dyeing and printingf= chemical industryf= plywood productionf=rolled water-proof material productionf= asphalt heatingf=non-woven hot-rolled machine, fiber glass press machinef= reaction kettlef= mould f=drying roomf= oven and other heating required industries. In wooden cases
Foshan metech aluminium technology co., ltd is a professional manufacturer, exporter and supplier of the full aluminium industry equipments and machinery, such as aluminium melting furnaces, aluminium holding furnaces, continuous casting and rolling machines, coal gasifier, aluminium dross processing machines , permanent magnet stirrer ect. We could offer all kinds of melting furnaces with different capacity (from 3 ton to 100 ton), different type ( regenerative furnace, reverberatory oven, tilting or stationary) , different shape( round, rectangular or vertical), different fuel ( oil fired, gas fired, electricity power ) etc. Different application (aluminum ingot, aluminum billite, recycling aluminum, aluminum scrap , wire and cable) etc.In a world, we could degsign and make the melting furnace according to your condition and need. So please tell me your detail conditions. The raw materials, daily outptu capacity, finished products etc. Aluminum melting furnaces, tilting aluminum melting furnaces, oil fired melting furnaces, industrial furnaces, stationary furnaces, twin-chamber furnaces, vertical furnace. Wooden box in containner.
The features of the walking beam heating furnace: (1)Walking beam reheating furnace is the most widely used in foundry field for metal ingots, billets, tubes and pipes. (2)Walking beam heating furnace is make up with moving parts and fixed parts. (3)We can produce all kinds of the walking beam heating furnace, such as walking beam furnace, walking bottom furnace and walking beam bottom combined furnace. (4)If the billet section is bigger than 120x120mm2, you can adopt the walking beam reheating furnace. (5)If the billet section is smaller than 100x100mm2, you can adopt the walking bottom reheating furnace. (6)We can design the furnaces according to your special requirements. Negotiable.
Application: This kind of furnace is used for annealing of various kinds of metal work pieces. For example, steel material and copper material. Structure: 1. Furnace shell body: The shell is rolled of 4mm steel plate, with strengthening profiled bar. The inside lining is built of aluminum silicate fiber cotton or bricks and typing bricks that placed evenly. Resistance wire is put on the bricks. 2. Furnace cover The furnace cover is made of 25MM steel plate. An insulating course is made the under-part of the cover. 3. There is a vacuum pressure gauge set on the furnace cover. 4. The furnace retort is made of 8MM stainless steel. A stop-off strip is welded on the bottom .On the top, there is a cooling water jacket and a sand seal device with binding bolt. 5. Heat element There are three kinds of resistance wire , 0Cr25Al5íó0Cr27Al7Mo2 and Cr20Ni80 ,for coiling.
Bogie type furnace, the structure of furnace is that there is a portable bogie on the bottom . Before heating, charging the bogie outside the furnace, the heating pieces put on the special iron, then the bogie will be pulled into the furnace by tractor, then will be pulled out for unloading, the heating work piece will be lift by the crane onto the metal forming equipment for processing. Our company produces these types of the bogie type furnace: (1)High temperature series (furnace temperature 0-1200 degree), bogie type furnace (5 tons - 100 tons) is suitable for high alloy steel for high temperature normalizing, annealing, quenching and tempering and roll. (2)Middle temperature series (furnace temperature 0 -950 degree), bogie type furnace (5 tons - 100 tons) used in general metal parts for normalizing, annealing in the air. (3)Low temperature series (furnace temperature 0 -750 degree), bogie type furnace(5 tons - 200 tons) apply to steel parts tempering, low temperature annealing and cores drying. Standard export package in pallet, and we can negotiable.
Furnace rolls Material for centrifugal barrels: 24/24NbTz,G18/8NiCr, 28Cr/48Ni/5W, 25Cr/20Ni, 24/24NiCrNb(1.4855), 25Cr/35Ni(1.4852),38Ni/18Cr(1.4865), 2.4633, 2.4879 or at customers request. Forged Shafts: 310 stainless steel, EN8, EN24 etc. Diameter: 50min Welding consumables: AWS A5.11 NiCrFe-3 2.4807 or 182KS or as per the buyer's requirements Working temperature: depending on the materials used (average: 800-1200).
Established in the early 80s of last century, weâ??re (Suzhou Dongsheng Industrial Furnace Co., Ltd.) specialized in researching, developing, designing and manufacturing of all kinds of industrial furnaces, such as Natural Gas Bell/Hood-type Annealing Furnace, Pit-type Vacuum Annealing Furnace, Trolley-type Electrical Heating Annealing Furnace, Spheroidizing Furnaces and so on ......all industrial solutions for the heat treatment of metal works industry. The Fuel Type(Gas) or Heating System(Electricity) can be selected based on the different requirements or conditions for/by the customer. You may refer to our website for more details: www.dsfurnace.com We have established the direct contact with many overseas buyers. We provide integral service of designing, manufacturing, installation and commissioning and have helped them to reduce their costs of equipment investment and production.