Centrifugal gold concentrator is a relatively new type of gravity concentration apparatus. The machines of pioneer s stlb series concentrator utilise the principles of a centrifuge to enhance the gravitational force experienced by feed particles to effect separation based on particle density. The key components of the unit are a cone shaped "concentrate" bowl, rotated at high speed by an electric motor and a pressurized water jacket encompassing the bowl. Feed material,typically from a ball mill discharge or cyclone underflow bleed, is fed as a slurry toward the centre of the bowl from above.The feed slurry contacts the base plate of the vessel and due to its rotation, is thrust outward.The outer extremities of the concentrate bowl house a series of ribs and between each pair of ribs is a groove. During operation the lighter material flows upward over the grooves and heavy mineral particles (usually of economic value) become trapped within them. Pressurized water is injected through a series of tangential water inlets along the perimeter of each groove to maintain a fluidized bed of particles in which heavy mineral particles can be efficiently concentrated. Centrifugal gold concentrator is an efficient equipment for recovering free gold in all particle size ranges,specially for recovery of fine gold which is lost during the operation of the gravitational concentrators(sluice boxes and jigs). It can be used not only for placer gold mining, but also for recover the natural gold from hard rocks, to replace amalgamation, and recover gold from the tailings.
Double-layer concentration table by Pioneers factory. A transmission box is arranged on a transmission box supporting seat at the end of a stand, a lower-layer supporting and holding frame of a Pioneers double-layer table support is arranged on a saddle-shaped seat of a slope adjusting mechanism, an upper-layer table surface and a lower-layer table surface are respectively arranged on an upper-layer supporting and holding frame and the lower-layer supporting and holding frame of the Pioneers double-layer table support through a shaking supporting mechanism, the end surfaces of the upper-layer table surface and the lower-layer table surface are connected through a table surface interlocking plate, and both ends of a connection screw are respectively in a hard connection with a transmission box linkage seat and the table surface interlocking plate. The invention has the advantages that the occupied area for installation is reduced half, the mineral treatment capacity of the single device is Pioneers doubled, the operating range of the site workers is greatly reduced; the basic engineering quantity of the device is reduced half, the consumption of construction materials for water supply and ore feeding and discharging flow pipelines is greatly reduced, the factory construction area of the concentrating mill is reduced half, and the energy efficiency is high, and is especially suitable for the Northeast area with special demands to the production environment. Double re-election shaker from Pioneers Manufacturing, including gearbox, articulating deck, bed strips, slope adjustment mechanism, motors, mine shafts, to sink, wherein: the transmission case in the frame ends of the gearbox support base (on 1?, lower bunk bed frame supporting the holding frame in the saddle adjusting mechanism slope, (? shaker shaker upper and lower surfaces C3) were placed by shaking the support mechanism of the upper bunk bed frame supporting the holding frame and the lower support clamp holder, shaking the upper surface and the lower surface shaker C3) of the end face interlocking plate is connected with the bed, connecting screw (? both ends and bed interlocking plate hard drive is connected to the linkage box seat.
Quick Details Structure: Cylindrical Type: Roller Brand Name: ATS Bore Size: 18 - 22 mm Outside Diameter: 45 - 50 mm Model Number: NU2204 Precision Rating: P0,P4,P5,P6 Seals Type: open/ZZ, RS, 2RS Number of Row: Single Row Place of Origin: Shandong, China (Mainland) Factory supply: Yes. Supply Sample: Yes. Certification: ISO 9001/ISO14001/TS16949 OEM: OK. Packaging & Delivery Packaging Details: 12*24*36 cm Delivery Detail: 3-30 days Factory price with high quality cylindrical roller bearing NU2204 Cylindrical roller bearings improved internal geometry, has a high load carrying capacity. Gear side end surface and the roller so that the new design has a high axial load bearing capacity. Good contact condition on the roller side of the contact zone profile has a good lubricating conditions and a low operating speed. This type of bearing is separable. As their rollers linearly come into contact with inner ring and outer ring with less coefficient of friction, these bearings hare very good capacity of radial load, suitable for electric motors, automobiles, transmission shafts, gear shafts and so on. Double row cylindrical roller bearings are good at the spindles do machine tools. Cylindrical roller and race are the line contact bearings, having large load capacity, mainly bear radial load. The friction between rolling elements and ribs is small, suitable for high-speed rotation.
Yq-n1390 co2 laser cutting machine features and advantages 1. Import hiwin linear square guide and high quality belts 2. High quality square tube welding frame with heat treatment, stable and durable, long life span 3. Speedy offline control system, support usb output directly, english interface, easy to operate 4. Three phase stepper motors and drivers (servo optional), which make sure machine work high speed and high precision 5. Support autocad, coreldraw output directly 6. Separate design availiable---machine can be dismantled to three parts, which is easy to put into narrow workplace. 7. Material can have a material pass thru unlimitedly 8. Closed design, make sure all smokes can be absorbed outside. Yq-n1390 laser cutting machine technical parameter Laser model: yq-n1390 Working area: 1300x900mm Laser type: hermetic and detached co2 glass laser tube Laser power : 60 / 80 / 100/ 130w/150w/260w Cooling way :water cooling and protection system Laser energy control : 0~100% set by software Location accuracy: ±0.01mm Engraving speed: 1000mm/s Cutting speed: 500mm/s Control system: speedy dsp , support u-disk output directly Supporting format: cdr, bmp, plt, dxf, ai, dst Software support: support autocad, coreldraw, photoshop, etc. Operating environment: windows98/2000/xp/win7/8, vista Working voltage: ac220v/50hz or ac110v/60hz Min.Shaping character: letter: 1mm*1mm Running environment: temperature:0-45°, humidity: 5%-95% Gross power:
?equipment model and name Csl-y impact specimen gap hydraulic broaching machine ? equipment usage Impact specimen notch broaching machine is the dedicated and affiliated equipment with metallic pendulum impact testing machine, the machine adopts hydraulic drive, electric control the rise and fall of broach, broach lifting speed can be adjusted, adopting the lubricating oil to lubricate blade mouth parts at the same time, to ensure the sample accords with a requirement gap size and surface finish.The machine due to the use of a forming principle, the machining gap of good identity. Broach manufactured high-quality high-speed w18cr4v steel alloy, and its high hardness, good wear resistance, long service life, per knife can be processed more than 20000 samples. ? applicable standard Gb/t229-2007« metal material charpy pendulum impact test method»; Astm e23-02a«metal material gap specimen standard impact test method»; Iso148-2008«metallic materials-charpy pendulum impact test»; Din 50 115-1991«metal material impact test special sample size and fracture judge» Iv main technical parameters Sample notch type U type(u2, u3, u5), v type(v2) Processing sample size 10×10(7.5 or 5)×55mm Broach hardness =hrc65 Installed broach quantity 2 Cutting speed 2.5m/min ( can adjust) System pressure 2.5mpa Hysraulic oil storage 25l Broach stroke 340mm(u2, v2), 390mm(u5) Broach materials W18cv4v Motor power 370w Dimensions 480mm×660mm×1200mm (l×w×h) Weight 200kg V standard configuration 1.Host one 2.V2 broach one 3.U2 broach one Vi optional accessories 1. U3 broach 2. U5 broach
Main features: 1) DSP offline control system. 2) Front & Rear entry for super-long plate to pass through. 3) Safety Magnetic switch to make sure safety during work. 4) Imported Linear rail guide with high durability, stability, precision. 5) Waste collect device, easy to pick up samples and save raw materials. 6) Most advanced Dual limit switch protection on XYZ axis, preventing the bump of laser head. 7) Dual red light pointer makes laser focus much easy, accurate and more personalized, no need any focusing tools. 8) Laser Machine software: 1) Lasercut5.3 with dongle and LCD Key Board ( Leetro Card) 2) Laser work software without dongle and LCD Key Board (RD CAM) 9) Separate control system box, separate laser power box, separate control panel, External spares plug and socket much safe for machine. 10) Optional Parts: Motorized up and down table, Auto focus, Rotary clamp, water chiller, etc. Applications: Application Materials: Acrylic, wood, bamboo, cloth, marble, organic glass, crystal, plastic, garments, paper, leather, rubber, ceramic, glass and other nonmetal materials. Application Industry: advertisement, arts and crafts, leather, toys, garments, model, building upholstery, computerized embroidery and clipping, packaging and paper industry. Technical Parameter: ModelCS1290CS1390CS1490CS1690 Working area(mm)1200 x 9001300X9001400X9001600X900 Standard Laser power:80w Optional Laser power:100W/120W/150W Gross power1600w Laser type:CO2 Laser tube Cutting depth:Acrylic 0-40mm, others material(varied according to the nature) Engraving speed :0-1000mm/s Cutting speed:0-600mm/s Resetting positioning accuracy:
i.About The Product The device is designed based on the electric equipment system on the Volkswagen Passet B5 body to holistically demonstrate structures and operation of the meter, lighting, illuminating, wiper, startup, charging, and ignition systems, and to support circuit terminal connection training. The device applies to theoretical teaching and maintenance training of the electric equipment system of the vehicle body in secondary and senior vocational skill schools, normal education and training institutions. ii.Features 1.A real and operable electric equipment system of the vehicle body is used to illustrate structures of the meter, lighting, illuminating, wiper, startup, charging, and ignition systems. 2.Switches and buttons of various electric equipment are operated to demonstrate operation of the meter, lighting, illuminating, wiper, startup, charging, and ignition systems. 3.Line terminals of electric equipment on the training bench have connection plugs. Trainees can improve their capabilities of diagram reading and terminal connection by connecting the plugs with middle harness based on the circuit diagram or maintenance data. 4.The training bench is installed with detection terminals to detect electric signals, for example, resistance, voltage, current, and frequency, of circuit components of the electric equipment system of the vehicle body. 5.The training bench's base frame is made in steel and the surface is paint-coated. Self-retention wheels are installed to ensure that the bench is flexible, reliable and endurable. 6.Equipped with intelligent fault setting and appraisal system, include fault setting, troubleshooting and assessment functions etc. iii.Basic Parameter 1.Size: 1700mm × 1100mm × 800mm (length x width x height) 2.Driving power supply: three phase four wire (three phase five wire380 ± 10% V 50 Hz) 3.Operating voltage: 12V DC 4.Operating temperature: -40? to +50? 5.Three-phase asynchronous motor ? Model: YT 100L1-4 ? Voltage: AC 220V/380V ? Power: 2.2 KW ? Rotation speed: 1420 r/min
i.About The Product The device is designed based on the circuitry of the automatic air conditioner of Toyota Corolla 1.8L to holistically demonstrate the structure and operation of the system. The device applies to theoretical teaching and maintenance training of the circuitry of the automatic air conditioner in secondary and senior vocational skill schools, normal education and training institutions. ii.Features 1.A real and operable circuitry of the automatic air conditioner is used to illustrate the structure of the system. 2.Various switches on the control panel of the air conditioner can be operated to demonstrate how each servo motor operates and the blower speed is adjusted. In this way, the device demonstrates operation of the circuitry of the automatic air conditioner. 3.The training panel is made of advanced aluminum-plastic plate with characteristics of not less than 4mm thick, corrosion resistance, impact resistance, pollution resistance, fireproof, and moistureproof. Its surface are processed by special craft and spraying primer. Never fade color circuit diagram and working principal diagram are painted on the board whose surface coating with varnish. The trainees can learn and analyze the working principle of the control system by referencing the diagram and the real object. 4.The training panel is installed with detection terminals to detect electric signals, for example, resistance, voltage, current, and frequency, of circuit components of the circuitry of the air conditioner. 5.The training panel's base frame is made of steel and the surface is paint-coated. Self-retention wheels are installed and a 24 0cm tabletop is fixed on the base frame to place materials and light testing devices. 6.Instead of using accumulators and requiring charging, the training panel connects to a 220V AC voltage which changes to a 12V DC voltage through the internal circuit. The 12V DC voltage protects the training panel against short circuit. 7.Equipped with intelligent fault setting and appraisal system, include fault setting, troubleshooting and assessment functions etc. iii. Basic Parameter 1.Size: 1600mm × 700mm × 1700mm (length x width x height) 2.External power supply: A.C. 220V ± 10% 50Hz 3.Operating voltage: 12V DC 4.Operating temperature: -40? to +50?
Working Principle: Vertical Vibration Casting pipe making Machine is one of the most advanced Concrete pipes making technology in the world at present, which integrate the technology of Mechanical, electric, Hydraulic, and the Automatics. This machine is easy to operate, much higher efficiency, and full-automatic. It can be used to produce the concrete pipe from DN600-3600mm, length 2-3 meter, and range from water drainage concrete pipe, Steel collar Jacking pipes, Box culverts, and the lined PVC or HDPE cement pipes and Manholes. The most important part of is the Vibrating Rod in the center of inner mould; the vibrator will produce high frequency exciting force while rotates at the fast speed, the exciting force will pass through to the inner mould, then to the vibrating transmission Spring, then to the outer mould. The concrete will become solid and density under the high strength vibration force, and form Quality pipe. Features: 1. Adopting the High Frequency Inner Vibrating, the concrete will become solid and density more evenly and more thoroughly. The pipe will be better in structure and stable in quality; 2. Using the half-dry cast concrete, the inner mould and Outer mould will be released instantly, so each diameter pipe just needs one set of moulds, which saves a lot of moulds investment, also saves a lot of time for workers assembling and disassembling the moulds, also improves the production efficiency. After releasing, the pipe could be curing by itself with the cement heat hydration, no need the steam curing, which also lowers the steam curing cost; 3. Wide range of production, this machine is capable to make not only water drainage concrete pipe, Steel collar Jacking pipes, but also Box culverts, Lined HDPE pipes and Manholes. 4. Variable Frequency motor, Inverter, Touch Screen and PLC, also the hydraulic technology are used in our machine. Top Quality and best price. The concrete pipe from DN600-3600mm, length 2-3 meter
4WD Mobile Robot with Tracking and Avoidance System-ALSRobotBase 4WD Mobile Robot Kit with Light Tracking System was produced by Harbin Alseon Robotics Technology Co., Ltd.. It is designed according to the control subject of previous Undergraduate Electronic Competition. 4WD Mobile Robot Kit has the light tracking senseor so that it can follow light to move.This 4WD Mobile Robot Kit also have Mini IR Detector sensor module, the module is a distance adjustable sensor. It has high adaptability to ambient light with high accuracy. It comes with transmitter and receiver. this module help mobile car detect obstacles and avoid easily. Specification: 1. Item Name: 4WD Mobile Robot Kit with Line Tracking and Avoidance System 2. Item Number: RB-13K074 3. Package Weight: 1.5 kg 4. 4WD Mobile Robot Kit Size: 206 mm x 200 mm x 65 mm Packing List: 1.1 x 4WD Aluminum Mobile Robot Car Chassis 2.1 x CarDuino UNO R3 Microcontroller 3.1 x Sensor Shield V5.0 for CarDuino UNO R3 Controller 4. 1 x L298 Dual H-Bridge Motor Driver 5. 5 x Mini IR Line Tracking Sensor 6. 3 x Mini IR Detector Photoelectric Sensor 7. 10 x 3Pin Jumper Wire 8. 1 x 10 sets M3 * 10 Nylon Standoffs 9. 1 x 10 sets M3 * 20 Nylon Standoffs 10. 1 x 10 sets M3 *8 Mounting Screws 11. 1 x USB Cable A-B for CarDuino Controller 12. 2 x Power Cable
Use: Ideal chicken meat deboning machine for making meat paste and muddy flesh. Separate bone and meat to get meat paste for further making ham sausage, meat ball and other meat food. Characteristics: Use the SUS304 stainless steel in line with international food standard. Mechanical deboning meat from poultry skeleton, carcass or the whole frozen chick, duck, goose. Frequency conversion control, speed can be adjustable. Low rotation speed, small temperature rise and easy maintenance Easy taking apart and cleaning, low maintenance cost Calcium content in fished products lower than 0.03%, meat fiber not destroyed. 24 hours of continuous work. mechanically separated meat or poultry Technical parameters: Model:TLY-300 Function : Chicken Deboning Capacity (Kg/h):200~300 Output Speed (r/ min):110 Power (KW):3 KW Feed Structure:Single Screw Rod Feed Screw Rod:80 Control System :Button Control Drive Structure:Direct connection between motor and reducer Reducer:TKAF Reducer Speed Ratio of Reducer:12.5 Machine Body:Stainless Pipe Welding Bunker (mm):450*300 Output part (mm):200*360 Output Type:Stacked blade type No.s of Blades:85 Packaging for shipment:Wooden Case for shipment Overall Dimension L*W*H (mm):1100*450*1000 the quail meat deboner is covered by plastic wrap,then packed in wooden case
We are most prominent manufacturer and supplier of deep freezers. Our product is manufactured by using best quality raw material as we source them from trustworthy vendor of market. We provide our best quality product at effectively competitive low cost and delivered within the time we committed. That’s why our product liked by our valuable customers. Our product is known for its best, effective and for its efficient working. Specifications: Product specificationDeep freezer Temperature-35*c to -40*c Cascaded/single stage refrigeration systemsSingle Cfc-free, environment friendly refrigerants r-508b (suva-95) and r-404aR-404 a only Braze plate heat exchangers (bphe)N.A. High density, cfc free, eco friendly puf insulation100 mm Air cooled condenser aided by continuous rated motor fanYes High purity copper coils all around the inner cabinet for efficient coolingYes Stainless steel interior and shelves made of ss-304 22 swg.Yes Outer cabinet crca with durable polyester powder coatYes Sub doors for inner compartment made of ss304/poly acrylic sheetYes Cam action lock/flat latchFlat latch Microprocessor control with digital display of temperature with pass word protectionYes Temperature sensors pt 100/ntcNtc Audio visual alarm for temperature deviation and power failureYes Low battery and hot condenser lamp indicatorsYes Safety interlock control between two stages of refrigeration and also high pressure safety switchesN.A. Battery backup (rechargeable)/ups for temperature display temperature chart recording and alarm during power failure mcbs for overload protection Yes Heavy duty castors, two with brakesYes Automatic voltage stabilizer with high/low voltage cut off and time delayYes
Technical specifications Overall dimensions mounted: lg 8.1 mx 2, 7 mxh 2m Built entirely of galvanized steel chroming. Vertical stroke 1170 mm Longitudinal slide stroke 7000 mm Cross slide stroke 1300 mm Total weight 650 kg (depending on engine) All movements are ball bearing. The blade shaft is mounted on two conical roller bearings. Trolley wheels are easily replaceable steel 380 v three-phase electric motor Petrol engine briggs & stratton Safety blade front and rear Simultaneous vertical displacement of the assembly by a single crank Accident all items can be replaced or repaired, beams, frames, truck, etc .... Sawing capacity Logs: maximum diameter of 1.4 m to 2 m and 6 m length maximum Timber: 25 cm x 25 cm (26 cm x 26 cm optional) Quarter sawn: 24 or 26 cm wide Volume of daily flow: from 6 to 12 cubic meters of wood sciépendant as sawing continues on the other station. It allows to increase the daily capacity by eliminating the time-sawing between two logs.) A portable sawmill ecopro2® includes: A sawmill with capacity 25 cm x 25 cm x 6 m A tilting system (this equipment allows to remove the waste and to position a new log without risk of collision logs / lumber mill in the open position while sawing continues on the other station. It increases daily capacity eliminating the time-sawing between two logs.) A sharpener (sharpener helps sharpen the saw teeth without removing the blade.) (+ link to the video) A toolbox A blade diameter 630 mm
Company profile Guangzhou airhorse compressor co., ltd is the professional manufacturing and exporter. We are specialized in air compressor research, development and production. The main products including screw air compressor, piston air compressor and air dryer etc. With the advanced design, high reliability, low noise, long running life time. Features of the belt driven screw compressor 1.The device is comparatively small in size but highly efficient.An economical ghh air end is attached to the motor via a durable belt, an arrangement designed to fully harness the raw power produced by the air end. 2.Air horse achieves the ideal equilibrium between power and air consumption throughout the loading phase for an exceptionally efficient performance. 3.A fully enclosed design acts to contain noise to a threshold of 68db or less 4.Avoid needless energy consumption with the integrated energy savings design.The machine automatically adjusts according to real-time power readings to eliminate load-free running. 5.The streamlined exterior of the enclosure is bright orange by design and projects vitality. 6.A multi-functional electronic controller complete with led display provides a convenient, user-friendly interface. 7.The certified machine is assembled with strict compliance to ce and iso9001 standards. 8.We offer a one year warranty covering the entire machine and three year standalone warranty for the air end. 9.A modified voltage service is provided with the purchase of the machine to accommodate various power Size(l*w*h)mm:1150*900*1380mm
Company profile Guangzhou airhorse company co., ltd, is the sub-corporation of jufeng compressor group co., ltd. , specialize in air compressor research, development and production.The main products include screw air compressor and pistion air compressor. Adopting advanced technique and workmanship, dewate piston air compressor own much advantage with reliable running , higher efficiency, longer life, are ideally suited for the light industrial, commercial or professional user. Guestes from domestic and abroad are invited to join us and share a brighter future. Features of the direct driven screw compressor 1.The device is comparatively small in size but highly efficient.An economical ghh air end is attached to the motor via a durable belt, an arrangement designed to fully harness the raw power produced by the air end. 2.Air horse achieves the ideal equilibrium between power and air consumption throughout the loading phase for an exceptionally efficient performance. 3.A fully enclosed design acts to contain noise to a threshold of 68db or less 4.Avoid needless energy consumption with the integrated energy savings design.The machine automatically adjusts according to real-time power readings to eliminate load-free running. 5.The streamlined exterior of the enclosure is bright orange by design and projects vitality. 6.A multi-functional electronic controller complete with led display provides a convenient, user-friendly interface. 7.The certified machine is assembled with strict compliance to ce and iso9001 standards. 8.We offer a one year warranty covering the entire machine and three year standalone warranty for the air end. 9.A modified voltage service is provided with the purchase of the machine to accommodate various power Size(l*w*h)mm:1600*1000*1360mm
Dbg-40b rebar parallel thread rolling machine Dbg-40b is designed for processing parallel threads for rebar mechanical connection, can process hrb335, hrb400, hrb500 reinforced bar with diameter 16--40mm. The max thread length is 80mm. Features 1 completing processing steel thread one-time with thread plump & smooth; 2 both right-handed threads &left-handed threads could be processed; 3 three points and one line, high concentricity and strong stability; 4 rebar simply feed and automatic carriage return after rolling; 5 shortening construction period. High processing speed and production efficiency. 6 easy and convenient operation; no pollution; no more material waste; no restriction of the weather. 7 reasonable structure, reliable performance. 8 fast installation, no need for skilled technicians. 9 processed thread is more precise£¬with small conical degree and surface is more smooth. 10 600-900 heads per day. Technical parameters Model:dbg-40b Rebar diameter:16-40mm Motor power:4kw 8a Voltage:3-380v 50hz Thread angle:75¡ã, customized Thread pitch:2.0-3.5mm Spindle speed:48-82 r/min Max thread length: 80mm Dimension:1*0.7*0.9m Net weight:400kg Certification:iso9001-2008 Wooden case, iron frame
Dbg-40b rebar parallel thread rolling machine Dbg-40b is designed for processing parallel threads for rebar mechanical connection, can process hrb335, hrb400, hrb500 reinforced bar with diameter 16--40mm. The max thread length is 80mm. Features 1 completing processing steel thread one-time with thread plump & smooth; 2 both right-handed threads &left-handed threads could be processed; 3 three points and one line, high concentricity and strong stability; 4 rebar simply feed and automatic carriage return after rolling; 5 shortening construction period. High processing speed and production efficiency. 6 easy and convenient operation; no pollution; no more material waste; no restriction of the weather. 7 reasonable structure, reliable performance. 8 fast installation, no need for skilled technicians. 9 processed thread is more precise£¬with small conical degree and surface is more smooth. 10 600-900 heads per day. Technical parameters Model:dbg-40b Rebar diameter:16-40mm Motor power:4kw 8a Voltage:3-380v 50hz Thread angle:75¡ã, customized Thread pitch:2.0-3.5mm Spindle speed:48-82 r/min Max thread length: 80mm Dimension:1*0.7*0.9m Net weight:400kg Certification:iso9001-2008 Wooden case, iron frame
Brief introduction of fish pellet fodder extruding machine 1.Ring die pellet mill is an ideal pelletizing machine for high quality feed pellets. Mported fc control; 3.Ll stainless steel conditioner with axial steam spraying extends the conditioning and cooking time; Reliable use. Features of fish pellet fodder extruding machine 1.Gear directly-connecting driving is adopted for high efficiency; 2.Full stainless steel feeder; variable pitch anti-bridging structure; imported fc control; 3.Ll stainless steel conditioner with axial steam spraying extends the conditioning and cooking time; 4.Main gear and pinion shaft adopt the carbonizing quenching with high accuracy; smooth driving, low noise and long service life; 5.Gearbox and driving holes¡¡¡ê¡è accuracy are guaranteed by specialized casting supplier and ncc; 6.The bearing and oil seal in the main drive are imported, and especially lubrication oil return system is available to ensure reliable bearing lubrication; 7.2 pc quick disassembling type precisely-cast die clamp is adopted to connect the die and quill flange, resulting in convenient and quick disassembling of die; 8.Pellet chamber door and feed chute are fully made of stainless steel with high anti-corrosion ability and long service life; 9.The connection between motor and gearbox adopts new type s-shape spring coupling with more convenient disassembling and assembling and more reliable use. 1. Wooden or metal case according to specific size of each equipment, we twine thick plastic coating for each machine. 2. Tight the equipment in the truck without space to ensure no rubbing during the transportation.
Ultra thin vertical fan coil units with 2 pipe system mfp-34tmt Specifications Dc brushless fan motor for option Four pipe systems are optional. 2 way valve or 3 way valve optional (fitted or supplied loose) Bms function is optional (mod-bus interface) Negative ion generator is optional. Features Consolo fan coil units with high quality Energy saving and easy control Ultra-thin design convector (fan coil): with only 130mm depth Cooling capacity 1.8kw air flow 340m3/h (200cfm) Left/right water tube connection can be changed freely. Advantages Stylish design: the units are designed in white color, other colors optional; it means that they will be suitable with most decoration schemes Ultra-thin design convector (fan coil): with only 130mm depth Super quiet ventilation: cross flow fan technology with special air directing settings makes our hydraulic fan coils exceptionally quiet Benefit Meco universal consolo type fan coil unit, easy to be installed, low installation cost. Using pvc drain pan with 2 water outlet, hollow structure design can enhance the thermal insulation properties, at the same time to prevent from leaking. Application Our compact design universal consolo fan coil units, widely used in home, banks, office buildings, ect. Instructions Standard export packing cartons; please read the instruction manual before install our fan coil units. Standard packing
Our mainly produces are high-precision, low-noise deep groove ball bearing, auto hub bearing, precision bearing, high-speed & precision bearing, shaft bearing and motor bearing. Our products are mainly sold to usa, japan, korea, brazil... Twenty countries around world. Auto bearings are 5300 , 10 , 35 , 19 , 10570 , 5840 , , , , , 5301 , 12 , 37 , 19 , 13180 , 7450 , , , , , 5302 , 15 , 42 , 19 , 17600 , 10200 , 11000 , 15000 , 110, , 5303 , 17 , 47 , 22.2 , 21000 , 12600 , 10000 , 13000 , 140, , 5304 , 20 , 52 , 22.2 , 24600 , 15000 , 9000 , 12000 , 230, , 5305 , 25 , 62 , 25.4 , 32500 , 20700 , 7500 , 10000 , 340, , 5306 , 30 , 72 , 30.2 , 40500 , 28100 , 6300 , 8500 , 510, , 5307 , 35 , 80 , 34.9 , 51000 , 36000 , 5600 , 7500 , 790, , 5308 , 40 , 90 , 36.5 , 56500 , 41000 , 5300 , 6700 , 1050, , 5309 , 45 , 100 , 39.7 , 68500 , 51000 , 4500 , 6000 , 1400, , Single row angular contact ball bearing, Model , dimension(mm) , point , limiting speed (rpm) , basic load rating cr(n) , basic load rating cor(n) , weight (g) * please visit www.Baimu-sh.Com for more information of (inch) deep groove bearings, ball bearings, roller bearings, precision bearings, automobile bearings special bearings, precision steel tube. Oem(chinese no.5 biggest bearing company)
