INCEPTION: G- GROUT MF-8 is highly fluid, single component, cementitious grout pre packed .
G-GROUT MF-8 powder It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks, pores and voids. It has much finer particle size than other hydraulically setting materials. It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality.
PURPOSE: G- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes. �·MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with water
BENEFITS: G-GROUT MF-8 can be injected with standard cement grouting equipment
Compatible with most of the admixtures to accelerate / retard the setting time
Supports all portions of structures
Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen
Non-toxic, Non-Hazards
Eco friendly & Cost Effective.
TECHNICAL SPECIFICATION
METHODS OF USES: Pre-process-
The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
Mixing:
MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes. Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
PACKAGING G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
STORAGE G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25C, protected from heat, frost and direct sunlight. SAFETY INFORMATION Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice
High performance concrete
High strength, low permeability concrete
Industrial flooring
Water tanks and sumps
Chemical storage tanks
Basements and sewerage pipelines
Refractory mixes etc.
Petroleum Refineries
Tunnels
Compatible with most of the admixtures to accelerate / retard the setting time
Supports all portions of structures
Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen
Non-toxic, Non-Hazards.
Eco friendly & Cost Effective.
G-GROUT UF-9 is professional grade material that used as crack injection grout powder. It has finer particle size. It is produced in well known manufacturing plant in a controlled environment resulting in consistent quality. It is manufactured by unique particle size distribution technique to enable finest particle size for application.
Purpose
Fixing ground anchors for sheet pile walls, concrete pile walls, retaining walls tunnels etc.
Defects on building masonry or pavement.
Filling the void between the lining and rock face in tunnel work.
Injection grouting of joints in masonry structures, restoration of heritage structures, dams, etc.
Benefits
G-GROUT UF-9 can be injected with standard cement grouting equipment
Compatible with most of the admixtures to accelerate / retard the setting time
Supports all portions of structures
Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen
Non-toxic, Non-Hazards
Eco friendly
Benefit in cost.
Stoage
G-GROUT UF-9 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.
HEALTH AND SAFETY
Extensive testing has shown G-GROUT UF-9 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT UF-9 but high concentrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
Packing
G-GROUT UF-9 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25kg plastic lined bags.
High performance concrete
High strength, low permeability concrete
Industrial flooring
Water tanks and sumps
Chemical storage tanks
Basements and sewerage pipelines
Refractory mixes etc.
Petroleum Referineries
Tunnels
Method of Uses:
â?¢ The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
â?¢ MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes.
â?¢ Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
â?¢ Packaging: G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
â?¢ Storage: G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.
â?¢ Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25�°C, protected from heat, frost and direct sunlight.
â?¢ Safety Information: Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation.
â?¢ It is recommended that suitable protective clothing, gloves and eye/face protection is worn.
â?¢ In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
G-GROUT MF-8 INCEPTION. G- GROUT MF-8 is highly fluid,single component, cementitious grout pre packed.
G-GROUT MF-8 powder It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks,pores and voids.
It has much finer particle size than other hydraulically setting materials.
It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality.
Purpose: G- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes.
MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with water
Benefit: G-GROUT MF-8 can be injected with standard cement grouting equipment
Compatible with most of the admixtures to accelerate / retard the setting time
Supports all portions of structures
Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen
Non-toxic, Non-Hazards
Eco friendly & Cost Effective
TECHNICAL SPECIFICATION
Properties G-Grout Value
Consistency Dry Powder
Colour Grey
METHODS OF USES�· Pre-process:
The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
Mixing:
MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes.
Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
Packaging: G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
Storage: G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.
Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25�°C, protected from heat, frost and direct sunlight.
Safety Information: Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation.
It is recommended that suitable protective clothing, gloves and eye/face protection is worn.
In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
96% G-Grout UF-9 Grouting Compound Powder is professional grade material that used as crack injection grout powder. It has finer particle size. It is produced in well known manufacturing plant in a controlled environment resulting in consistent quality. It is manufactured by unique particle size distribution technique to enable finest particle size for application.
Method of Uses:
The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes.
Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
Packaging: G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
Storage: G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.
Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25�°C, protected from heat, frost and direct sunlight.
Safety Information: Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation.
It is recommended that suitable protective clothing, gloves and eye/face protection is worn.
In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
MAXX Powergrout 60 is a free flow non shrink high strength cement based expansive grout. it is developed by using special additives & graded filler. it is recommended for grouting with design strength up to 60 MPa.
Area of Application
Maxx Powergrout 60 is ideal for heavy machinery base plate, tie bolt holes, crack treatment core filling, bearing plates, columns in precast. It is essential to withstand static & dynamic load.
Features & Benefits
1) High early strength
2) Non -Shrink
3) Chloride free
4) Enhance durability
5) Enhanced flow properties and pot life
6) No bleeding and better mix consistency
INCEPTION: G- GROUT MF-8 is highly fluid, single component, cementitious grout pre packed .
G-GROUT MF-8 powder: It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks, pores and voids. It has much finer particle size than other hydraulically setting materials. It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality.
PURPOSE: G- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes. �·MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with water
BENEFITS: G-GROUT MF-8 can be injected with standard cement grouting equipment
Compatible with most of the admixtures to accelerate / retard the setting time
Supports all portions of structures
Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen
Non-toxic, Non-Hazards
Eco friendly & Cost Effective.
TECHNICAL SPECIFICATION
Properties G-Grout Value
Consistency Dry Powder
Colour Grey
METHODS OF USES: Pre-process:
The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
Mixing:
MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes. Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
PACKAGING G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
STORAGE G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25C, protected from heat, frost and direct sunlight. SAFETY INFORMATION Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
Method of Uses:
â?¢ The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
â?¢ MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes.
â?¢ Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
â?¢ Packaging: G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
â?¢ Storage: G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.
â?¢ Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25�°C, protected from heat, frost and direct sunlight.
â?¢ Safety Information: Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high concentrations of dust may cause irritation.
â?¢ It is recommended that suitable protective clothing, gloves and eye/face protection is worn.
â?¢ In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
SH 200 is a ready-mixed, non-shrink, non-metallic, flow-able, high-strength structural grout.
SH 200 contains a balanced blend of washed and graded silica sands, Portland cement, flow improving compounds, and a shrinkage compensating system which produces a volume stable structural grout.
SH 200 produces high early and ultimate strengths without intermediate or latent shrinkage.
SH 200 remains stable without failure from compressive loading, impact, lateral thrusts, high heat or continuous vibration. It is scientifically proportioned and is ready for use at varied consistencies from plastic to fluid.
Dubond's Dupoxy is a stage of Grouting material of highest quality that provides asethetic effect and durability. It perfectly prevents stains,spillage,chemical attack in filled groove thicknesses of tiles,stones. Dupoxy is thixotropic two part epoxy based formulation having excellent resistance to wear and European choice special sheen affect which makes it a darling choice of consutant fraternity.
Part A consists of mixture of epoxy resin,siliceous aggregates and additives.
Part B consists of mixture of organic catalysts.
The advantage of two part epoxy grout system of Dupoxy is its high user friendliness that is i.e.the filling of this GEL filler in the grout is easier than all the distantly following equivalent products. It has a matt finish with an ingredient that provides crystalline sheen affect with ease of clean ability.
It is suited for residential and commercial installations 1ncluding those with total hygiene control, damp and wet environments.
* X1 Grout Pump series gives a main advantage for the operator like valveless positive-displacement pumps are capable of transporting cement based grouts safely, quickly and pulsation free. These units comes with variety of Rotor and Stator geometries providing unsaid advantage over any type of cement based grout been used.
Performance Data
Capacity Range : upto 60 m3/hr
Pressure : upto 40 Bar
Features and Benefits
* Separate under gland shaft for quick maintenance and servicibility
* Economical units and absolute value for money
* Continuous low-pulsation conveyance unaffected by fluctuations in pressure and viscosity
* Conveyance volume in proportion to rotation speed with high dosing precision over the entire rotational-speed range
* High pressure and high volume capability
Physical property:
Melting Temperature: -49 ºC
Boiling Temperature: 240-243 ºC
Density at 20ºC, g/cm3 : 1.204
Flash Point: 123 ºC
Ignition Temperature: 455 ºC
Packaging Details
250kg drum;1200kg/IBC; 23-24MT ISO TANK
Application:
1. Reactive diluents for urethane and epoxy resins
2. Cleaner and degreasers
3. Chemical intermediates
4. Cosmetics additives
5. Electronic industry(media) as filler
6. Paint stripper
7. Foundry sand binder, wood binding resins
8. Coal mining ,excavation and tunneling
9. Removal of CO2 from Urea manufacturing, oil gas, natural gas etc
10. Setting agent in chemical grouting to get easily controlled gel time
Maxxcon RM is a high performance, polymer modified repair mortar designed for restoring damaged, cracked or spalled concrete and plastered wall surfaces. it provides excellent adhesion, workability and strength, making it ideal for structural and non -structural wall repairs. the non - shrinking formulation ensures durable, crack - free repairs with a smooth finish suitable for painting or protective coatings.
Areas of Application
Spalled / damaged wall surfaces
Cracks and voids in plaster & concrete walls
Honeycombs and surface defects
Internal & External repairs
Features & Benefits
1) Polymer modified formula - Excellent adhesion to concrete & plaster
2) Non - Shrinking repair mortar - prevents secondary cracking
3) High compressive & flexural strength - durable, long - term repair
4) Smooth workable consistency - easy to apply & finish
5) Reduced rebound & wastage - economical application
6) Paint able after curing - ready for decorative finishes
