Electrical voltage tester Contact ac voltage range: 80v to 500v Long life of neon lamp, turn/off 50000 times or more, flash up to 20000 hours Shell made of transparent plastics, impact-resistant, insulation voltage up to 1000v The end with a hole for hanging up, hardness of blade head up to hrc52 40x26x22.5cm N/g 7.56kg/9.93kg
Designed to test all types of relays. 6 x 30 a ac/dc 4 x 125 v ac/dc 1x 3 a /100v 1 x 0-265 v aux DC 8 binary inputs 4 binary outputs Rs 232, ethernet port Based on linear power amplifier techmology, the test set is highly accurate and is the economical solution for relay testing. 15 kg
A great scientific innovation must lead to a great technological breakthrough. Tck•w portable rope testers weigh only 1.8 kg, about 1/6~1/25 of the weight of conventional ndt testers. The sensitivity of tck•w sensors could reach 5v/mt, and about 700times higher than conventional sensors. The gap between sensor and wire rope is about 20-30mm which achieves non-contact inspection, it does not affected by grease, normal warped wire, and rope-running speed which shown that passing-through capacity is good. When an inspection is completed, tck•w rope testers are capable to display testing data, flaw graph, data table, and test report on lcd screen. After connected to a computer and printer, a formal test report could be printed, which provides scientific reference for users to use wire ropes more safely and replace wire rope more properly. Key features 1. High inspection precision, strong resolution and stable performance: “weak magnetism sensor” technology invented uniquely by our company, its sensitivity is 700 times higher than traditional tester. The sensor has strong resolution, and can inspect quantitatively actual wire rope flaws under various working status. 2. Small volume and light weight: the weight of w portable flaw detector is less than 2kg, which is only 1/6—1/20 of similar products at home and abroad. 3. Easy operation: inspection system realizes intelligent “fool” operation; on-line lock or unlock only needs 1 second; it only needs one person to operate, and the operation is much easier than using a mobile phone.
Features: * LCD display of 128 64 matrix is used. * Hardness scales(HV ,HB,HRC,HRB,HRA,HS). * RS232 interface and USB to PC * Max 600 groups impact times:32¡«1 of data can be stored at internal. * Back light display has been used to make convenient or the user in poor light. * Upper and lower limit can be preset. It will alarm automatically when the result value exceeding the limit. * Material of cast steel¡± is added HB values can be read out directly when D/DC impact device is used to measure cast steel¡± workpiece. * Power is two of AA battery. Continuous working period: approx. 100 h (no back light on). * Software of PC can be installed according to the requirements of user. The function will be more powerful to satisfy the more demands of quality control and management.
Ft-f1 fogging tester Characteristics: Determines auto's fogging characteristics precisely, guarantees automobiles driving safely. Be applicable for the laboratory and works in low noise. Data test and analysis with professional software, convenient and prompt. Bath temperature controlled by thermostat can be kept constant to 0.1ªc, creating precise testing conditions. Designs friendly and integrally, operates safely and conveniently. World-famous brand elements with stable and reliable performance. The strictly controlled constant thermostat can be used for the other experiments. Conforms to din 75201, iso 6452, sae j1756.
Test different types of MU in electronic transformer input, magnetic transformer input and electromagnetic transformer input, integrate with reliable analog output and high-speed digital signal process. Support GPS, IRIG-B and PPS timing method, 0.05% high accuracy analog output and strong abnormal SMV function. POM2-3333 can also test SMV accuracy, data process delay, clock synchronization, time accuracy, abnormal SMV and SMV time dispersion,etc items. Functions: Background software can do programming of the electrical wiring graph and configuration and fault simulation of protection relays, analog the setting of specifications of MU, digital terminal devices and specifications setting of fault and fault points. The entire testing and operation process can be controlled by the background software. Two kinds of test modes ensure absolute time delay parameters of MU and complete the SMV response time test accurately. The timing function makes tests on MU's clock synchronization and time accuracy, etc time characteristics. SMV analysis analyzes SMV and GOOSE messages output by MU in real-time. It tests the MU's self-checking and fault process by SMV quality bit, signal remark in GOOSE or the defined warning information in GOOSE. The electric quantity in SMV can display the wave, binary status and previous displacement time. The SMV and GOOSE abnormal output by MU can be judged and analyzed by multi abnormal SMV detection systems. The accurate timing remark on SMV can statistic and evaluate the time dispersion of MU's SMV.
Working Principle Mechanical dead-weight testers or primary standards are the most accurate reference instruments for pressure. Their functional principle is based on the physical principle of pressure = force/area. Mass pieces placed on the top of a piston-cylinder system are the source of a precisely defined force. By producing a certain (counter) pressure inside the pressure balanceÂ an equilibrium is achieved: the mass pieces, including the free-running piston of the piston-cylinder system, are floating, which will lead to a very accurate pressure at the test port. Model (optional) CW-6T CW-60T CW-250T CW-600T CW-1000T CW-1600T range (MPa) 0.04-0.6 0.1-6 0.5-25 1-60 2-100 2-160 â?? Applications: digital pressure gauge, precision pressure gauge and pressure transmitter testing, adjusting and calibrating. Accuracy: 0.005%F.S.; 0.01%F.S.; 0.02%F.S.; 0.05% F.S. â?? Materials: Piston (the rod and cylinder): tungsten carbide Weight: Non-magnetic stainless steel (level 0.005, 0.01, 0.02); Carbon steel (level 0.05) Base: stainless steel Working medium: 25MPa: the mixed oil (transformer oil and kerosene oil) 25MPa: sebacate oil Performance features: Accord with JJG59-2007; Able to test two gauges synchronously; Applied the fast pressure plug; no oil leakage; Abrasive resistance is improved because of the high-tensile and high-hardness wolfram carbide material; The piston rod is anti breakage structure. 1.The piston system configures Eddy current displacement sensor,adopts integrated double row LCD digital cursor display ( which is firstly invented in China), therefore piston position can be observed anytime, which is sensitive, intuitional,accurate. 2.With pre-pressure pump, it can fill oil to large capacity gauge, several gauges or long distance calibration pipeline system. 3.The tester junction with stop valve and piston stop valve, so it can be used as independent pressure source, when piston stop valve is closed. -
Air permeability tester is suitable for the analysis and determination of the porosity, the air permeance and the air resistance of various kinds of battery separation membranes, paper, paperboard, textiles, non-woven fabrics and other materials.
Features 1. Our own patent technology. 2. Large size touch screen operation. 3. Designed based on various standards. 4. Falling ball test available. 5. Method a, method b, customized method available. 6. Test results, curve display. 7. Result multiple units display. 8. Micro-printer prints mini-report. 9. High performance pneumatic sample clamp. 10. Foot pedal operation available. 11. Safety cover. 12. Result statistics. 13. Rs232 communication port. (optional)
Features 1. Embedded system control, patent technology. 2. Touch screen operation. 3. Real color tft lcd display. 4. Burst, standard creep, creep-to-burst test. 5. Open package test is available. (optional) 6. With and without restraining plates test is available. (optional) 7. High speed sampling for test accuracy warranty. 8. Over pressure protection. 9. Low power consumption. 10. Rs232 communication port. 11. Dsm computer software support. (optional)
Application This thickness tester is based on contacting method and designed to precisely measure thickness of plastic films, aluminum foil, aluminized films, plastic composite films, paper-plastic composite films, coextruded films, aluminum foil composite films and many others. Features 1. Embedded system control, patent technology. 2. Touch screen operation. 3. Real color tft lcd display. 4. Max, min, aver, sd result display. 5. Manual test and automatic test. 6. Multiple ranges selectable. 7. Micro-printer prints mini-report. 8. Result with multiple units display. 9. Sample auto feeder available. (optional) 10. Traceable standard block calibration. 11. Rs-232 communication port. 12. Professional computer software support.(optional)
Application GTR-7001 is based on the differential pressure method, and is professionally applicable to the determination of gas transmission rate as well as solubility coefficient, diffusion coefficient and permeability coefficient of plastic films, laminated films, high barrier materials, sheeting, metal foils, rubber, tires and permeable membranes. Features Vacuum differential pressure method Patent technology 3 specimens test simultaneously and independently Computer control One-button test, test automatically through whole process High accuracy vacuum sensors embedded in 3 Chambers with independent temperature sensor Test under various RH conditions with Humidity generator (optional) Environment temperature and humidity sensor inside Permeability coefficient ,solubility coefficient and diffusion coefficient test Chambers with water bath temperature control technology Unit based on embedded system,24bit AD Multiple test modes optional Data curves display Traceable reference film calibration Supports DSM system (DSM, lab data management system) Technical Indexes Test range: 0.01 - 190,000 cm3/m2â?¢24hâ?¢0.1MPa (Standard) Resolution: 0.001cm3/m2â?¢24hâ?¢0.1MPa Samples: 3, independent Vacuum accuracy: 0.1Pa Temperature range: 5C - 95C Temperature accuracy: Â±0.1C Humidity range: 0%RH,35%RH-90%RH,100%RH (optional) Humidity accuracy: Â±1%RH (optional) Sample thickness: less 5mm Sample size: >= 150mm * 94mm Test area: 48cm2 Test gas: O2, N2, CO2, He, etc Differential pressure: -0.1MPa - 0.1MPa Gas interface: Ð¤8mm Dimension: 730mm * 510mm * 350mm Power supply: AC 220V 50Hz Net wt. : 63kg Standards ASTM D1434, ISO 15105-1,ISO 2556,GB/T 1038-2000,JIS 7126-1,YBB 00082003 Configuration Delivery: Main unit, computer, G-TRANS software, Temperature controller, vacuum pump(BOC Edwards), tank regulator, PCIE card, communication cable, sample cutter, vacuum grease. Optional: Humidity generator, Reference film, vacuum grease, sample cutter, DSM system.
Application Wvtr-9001 is based on the electrolytic sensor method and available for the water vapor permeability test of flexible films, sheeting and packages. It can test 3 specimens in one operation with independent results. Features Electrolytic sensor method Patent technology Film and package test 3 specimens test simultaneously and independently One-button test, test automatically in whole process Multiple test modes optional Data curves display Computer control Digital flow adjustment 3 chambers with 3 temperature sensors Environment temperature and humidity sensor inside Chambers water bath technology Unit based on embedded system, 24bit î?-î£ ad Pressure, ppm water sensor and temperature overload protection Traceable reference film calibration Supports dsm system (dsm, lab data management system) Standard Iso 15106-3, gb/t 21529, din 53122-2, ybb 00092003 Configuration Delivery: main unit, computer, w-trans software, temperature controller, tank regulator, pcie card, communication cable, sample cutter, vacuum grease. Optional: package fixtures, reference film, vacuum grease, sample cutter, dsm system.
GTR-7004 tester is suitable for the analysis and determination of the porosity, the air permeance and the air resistance of various kinds of battery separation membranes, paper, paperboard, textiles, non-woven fabrics and other materials.
Scope Standard ASTM D93, GB / T261-83 and ISO2719-1988 international standards. Features 1, large-screen LCD, friendly user interface 2, also has a fault of Jane function, automatic fault prompts 3, automatic temperature control, automatic lid opening and ignition, automatic print, automatic cooling, automatic air pressure correction is completed and the machine automatically displays the flash point temperature, built-in mini thermal printer to automatically report the test results 4, using USB / 232 communication interface to communicate with the host machine, a centralized management system for easy composition 5, from Germany imported stainless steel temperature sensor for detecting the temperature data is accurate and reliable 6, mechanical moving part of the servo-driven belt drive, work without gaps, low noise, reliable easy to damage, no lubrication maintenance. 7, just set the expected flash point, the instrument automatically in strict accordance with the standard test, the test ends automatically print test results, and there is a tone. Without judgment and do not rely on the operator's proficiency. 8, thermocouple detection sensitivity high detection accuracy, durability and easy maintenance. 9, sample box with built-in cooling mode heating thermostat thermal compound, and the use of German imports whisk Dan Adams compressors, thermostats no lag reliable, easy to damage Technical Parameters 1. Environment: Temperature 0 ~ 60 ? Relative humidity: = 80% 2, Display: large-screen LCD 3, heating rate: less than 50 ? 1 ? / min, higher than 50 ? 2-3 ? / min 4, temperature range: -30 ~ + 80 ?, accuracy ± 1 ? 5, the temperature measurement element: PT100 stainless steel temperature sensor 6, the ignition: gas flame ignition 7, Detection: Automatically detects a flash fire and automatically print test data. 8. Communication: USB / 232 communication interface. 9, cooling system: compressor cooling 10, print: You can print the results of this experiment or any print storage 11, using the power AC220V 50Hz, the total power: 1.5 kw
Purpose SYF71 crack width and depth tester is used to test the crack depth and width. It is one professional crack measurement in one comprehensive test instrument, mainly used for crack detection of bridges, tunnels, walls, concrete pavement, metal surface. Specification The People's Republic of China Housing Security accreditation standards --- GJ125-99 Technical specification for inspection of concrete defects by ultrasonic method (CECS 21:2000) Performance/Functions 1. Large-screen display: 5 "color LCD display with a resolution of 640 * 480; 2. A high degree of intelligence: the boot that is measured, without human involvement parametric interpretation, display sewn deep value; real-time detection and automatic interpretation crack width, but also the manual interpretation crack width value, manually move the cursor to define the crack boundary is displayed on the screen scale ruler display crack width value; 3. Deep test: maximum test depth up to 650mm; maximum width up to 8mm 4. Dedicated scale: instrument equipped with a dedicated scale, portable and practical, to improve the efficiency of the test. 5. The instrument can be set and saved the test date: user-friendly data management 6. Easy data transfer: the instrument can be directly connected to the computer, copy pictures and data transmission without U disk; 7. Powerful professional windows data analysis processing software: data can be imported into Word and Excel, convenient and user-friendly post-processing of data. Technical Measurements 1. Crack depth testing range: =< 650 mm; test error: =< 10%; 2. Crack width value of measuring range: 0 ~ 8mm; width measurement accuracy: 0.01mm; 3. Crack depth test data storage capacity: 6000 set of test data; 100,000 and can store the image and width of cracks measured point data; 4. LCD screen resolution: 160X128 dot matrix 5. Built-in rechargeable lithium battery, can work continuously for eight hours; 6. Operating Temperature: -10 ? ~ +50 ?; 7. Host size: 190mm × 183mm × 84mm
(Equipment for Control of Resistance to Expand and Explosion of PET Bottle) For PET bottles - Simulating filling process PBBT-1 PET Bottle Burst Tester is a specialized test equipment for testing the PET bottles. It’s designed in accordance with the three international test methods which are commonly used. Users can choose the test method basing on their requirement. The PBBT-1 is capable to test the capacity of resilience under certain pressure or the rupture test of the PET bottle. Through the reproduction of the pressurization, the process has been linearized and it increases to the predetermined point or the point of bursting. After selecting the test program, the cycle will start automatically depending on the settings. The touch screen displays the pressure value in real time and record the maximum pressure and burst pressure. Characteristics: • Standard equipment for the PET bottle industry. • 3 international test methods are available • PLC integrated & Touch screen control • Automatic clamping and filling system • Can store 10 operators and 30 products • User defines the product lot number and sequence number • Display curves of pressure and volume expansion during the test • Monitors and records the temperature of the water during the test • Applicable to 2.5 L bottle (consult us for bigger size) • Stainless steel design ensures the durability of tester • RS232C data output: connected to either printer or software • Integrated calibration function Modes details: Fill ramp mode: The filling ramp mode is designed to simulate the situation of filling lines of PET bottles. Under this mode, the PET bottles are pressurized rapidly to the initially preset pressure and maintained for a given time (for example 13 seconds). Then continue to increase the pressure with a speed of 0.1 bar/s until the outbreak of the bottle or reaching the max pressure or volume. Preset parameter includes: initial screening pressure, maximum pressure, and expansion of volume limit. Burst mode: Under this mode, PET bottle will be pressurized rapidly to the initially preset pressure and maintained for a predefined period. Custom mode: Under this mode, user is able to create the pressure curve to meet the particular conditions of control. Users can define the pressure curve by steps, after the adjustment is made, the corresponding curve will be displayed on the user interface.