• 4000 hour rated lamp source • OSRAM SIRIUS HRI 180W projector lamp (8400lumen, 7500°K, 4000H) included • 40650 Lux @ 20m • 2.5° beam angle • No need for adjustment of reflector or lamp • Anti-reflection lenses • 1 color wheel with total 13 colors plus open • Variable direction rainbow effect with speed adjustable • 1 rotatable gobo wheels with 12 rotatable, indexable and interchangeable gobos plus open • Variable speed gobo scrolling in both directions • 12.0mm outside, 8mm image diameter (Gobo Size) • 1 rotatable and indexable 8-facet prism with speed adjustable and variable direction • Macro-function for rotatable gobo/prism combinations • Variable Frost Filter (Hybrid effect for Wash) • Dual flag mechanical dimming system • Variable speed strobe effect • Preset variable/random strobe and dimming pulse effects • Motor driven focus from near to far • 540°/630° PAN and 265° TILT movement • Automatic Pan / Tilt position correction • 16 bit smooth and precise resolution for PAN/TILT movement • 3-phase motors for fast, quiet and accurate Pan / Tilt positioning • Vector Mode with blackout MIB function • Blue LCD Display • 14 DMX channels USITT DMX-512 (16-bit resolution) • Other DMX modes available(16CH for Vector Mode) • Customizable DMX channel assignment • DMX, stand-alone, master/slave, sound activated mode • DMX recorder and edit function integrated • Software update • 3-pin or 5-Pin XLR serial input/output • Fan cooling system • Constant temperature readout / management function • DB rating @ 1M = 54,18db • 2 x 1/4 turn fastening Omega Clamps • Electronic ballast and power supply • Input Voltage: AC 90-260V 50/60Hz • Light Source: 1* OSRAM SIRIUS HRI 180W projector lamp • Control Signal: DMX512, master-slave and sound activated or auto operation • Control Channel: 14 DMX Channels • Power Consumption: 342W. • Dimensions: 359(D)x329(W)x513(H)mm • Packing Dimensions: 620(D)*430(W)*415(H)mm • Net Weight: 15kg • Gross Weight: 18kg.
Name: Capsule water-based varnish Model: H-8006 Use: capsule varnish , for plastic and paper package. Description: H-8006 is using a variety of specialty monomers synthesized varnish which used for plastic. This product has good fluidity, easy to operate, fast drying, and high brightness. Suitable for PET, the adhesion between the film and paper. Applied to paper, plastic bonding with a solid. Appearance: milky white liquid, Solid content 40% Viscosity (seconds): 13 ~ 14, (3 cup, 25 ), Gloss: 55 5 Notes: 1, It based on conditions of use plus appropriate diluent (water) or alcohol and water (1-5:1) mixture dilution. In order to achieve gloss and abrasion resistance requirements of the situation according to the paper, roll coated with light plus 5 to about 15% thinner, with inline coating liquid, the use of high viscosity coating process should be adjusted to increase the amount of diluent the appropriate viscosity. 2, Varnish on paper should meet the principle, if excessive dilution will affect gloss, abrasion resistance and leveling; the contrary will result in dilution of inadequate leveling varnish is not good, the drying rate is too slow . 3, depending on fuel quality and gloss paper requirements, are generally on-line coating of :2-5 g / m, offline coating 3-7g / m. 4, drying method: to use infrared drying, hot air or heat pipe heating and drying. Drying equipment operation during the first table shows the temperature not lower than 70 . 5, Take 12 hours after polishing of the varnish in order to achieve optimal performance. 6,It can use water to clean equipment, the dry varnish can used Isopropyl alcohol or alcohol to clean. 7, the product of alkali-soluble varnish, when veneer to the cartons (laminating), try to choose a neutral or weakly alkaline (PH 10) adhesives, when used starch caustic soda glue (yellow glue) fluid, Please be strictly controlled to avoid excess glue with a glue penetrate varnished surface caused by dissolution of the coating adhesive. Package: 25KG/50KG/120KG plastic containers, sealed in a cool place, the shelf life is one year.
Name: Water-based Varnish (high viscosity) Model: H-5312 Use : high gloss ,high viscosity ,for paper package printing Description: H-5312 is an environmentally friendly water-based varnish, excellent wear resistance, high gloss, gloss retention, dry fast, good printability. A variety of ink has good wetting leveling, printing machine is easy to clean s. It is meet the national and EU environmental standards, through the EU ROHS test, compliance with international environmental requirements. Scratch resistance is strong, mainly used for dusting and more printing, high wear resistance. Appearance: milky white liquid, Solid content: 461%, Viscosity (Viscosity Cups 3 , 25 seconds): 18 ~ 20, Gloss: 4 ~ 7 Notes: 1, It based on conditions of use plus appropriate diluent (water) or alcohol and water (1-5:1) mixture dilution. In order to achieve gloss and abrasion resistance requirements of the situation according to the paper, roll coated with light plus 5 to about 15% thinner, with inline coating liquid, the use of high viscosity coating process should be adjusted to increase the amount of diluent the appropriate viscosity. 2, Varnish on paper should meet the principle, if excessive dilution will affect gloss, abrasion resistance and leveling; the contrary will result in dilution of inadequate leveling varnish is not good, the drying rate is too slow . 3, depending on fuel quality and gloss paper requirements, are generally on-line coating of :2-5 g / m, offline coating 3-7g / m. 4, drying method: to use infrared drying, hot air or heat pipe heating and drying. Drying equipment operation during the first table shows the temperature not lower than 70 . 5, Take 12 hours after polishing of the varnish in order to achieve optimal performance. 6,It can use water to clean equipment, the dry varnish can used Isopropyl alcohol or alcohol to clean. 7, the product of alkali-soluble varnish, when veneer to the cartons (laminating), try to choose a neutral or weakly alkaline (PH 10) adhesives, when used starch caustic soda glue (yellow glue) fluid, Please be strictly controlled to avoid excess glue with a glue penetrate varnished surface caused by dissolution of the coating adhesive. Package: 25KG/50KG/120KG plastic containers, sealed in a cool place, the shelf life is one year.
Name: water-based varnish (self-adhesive) Model: H-5803C Use: for in-line printing , wet to wet printing , self-adhesive , for noodles package . Description: H-5803C is a plus by a special acrylic polymer emulsion with functional additives varnish, It has strong adhesion for the paper after it was hot of the Ultrasonic heating. This varnish has excellent gloss, good gloss and color retention, dry fast, good printability. The wet-wet and wet-dry printing has good wetting leveling, strong anti-alcohol ,printing machine is easy to clean. Dedicated to the noodles package(such as Master), which need ultrasonic to glue Automatic .This varnish is used off-line coating, can also be used for inline coating. Appearance: milky white liquid, Solid content 40%, Viscosity (seconds): 18 ~ 20, (3 cup, 25 ), Gloss: 55 5 Notes: 1, It based on conditions of use plus appropriate diluent (water) or alcohol and water (1-5:1) mixture dilution. In order to achieve gloss and abrasion resistance requirements of the situation according to the paper, roll coated with light plus 5 to about 15% thinner, with inline coating liquid, the use of high viscosity coating process should be adjusted to increase the amount of diluent the appropriate viscosity. 2, Varnish on paper should meet the principle, if excessive dilution will affect gloss, abrasion resistance and leveling; the contrary will result in dilution of inadequate leveling varnish is not good, the drying rate is too slow . 3, depending on fuel quality and gloss paper requirements, are generally on-line coating of :2-5 g / m, offline coating 3-7g / m. 4, drying method: to use infrared drying, hot air or heat pipe heating and drying. Drying equipment operation during the first table shows the temperature not lower than 70 . 5, Take 12 hours after polishing of the varnish in order to achieve optimal performance. 6,It can use water to clean equipment, the dry varnish can used Isopropyl alcohol or alcohol to clean. 7, the product of alkali-soluble varnish, when veneer to the cartons (laminating), try to choose a neutral or weakly alkaline (PH 10) adhesives, when used starch caustic soda glue (yellow glue) fluid, Please be strictly controlled to avoid excess glue with a glue penetrate varnished surface caused by dissolution of the coating adhesive. Package: 25KG/50KG/120KG plastic containers, sealed in a cool place, the shelf life is one year.
Complete with power LED ( 50000 h). Very high light intensity 1212 lm, light colour 6500K daylight white. Beam spread 20° Max. Lighting distance: 68m / 1 Lux Protection degree IP69K. Dimensions: Ø 130mm, depth 50mm. Floodlight model DOX is distinguished by a monolithic aluminium die-cast body extremely robust and compact, containing 12 led chips housed in a sealed, waterproof and maintenance free, compartment. The body is mounted on a steel fixing bracket through a coil, helping absorption of vibrations and also allowing small aiming adjustments. Most relevant peculiarity of model DOX is the ability to operate under a really flexible supply ranging from 9V to 30V DC allowing use with batteries, small generators and also in combination with solar photovoltaic panels. The floodlight is well apt for lighting tasks on boats and and industrial vehicles with a power consumption of only 18W and a powerful light beam. Use: DOX is a led work light with a great efficiency and minimal power consumption requiring a very low voltage power supply and with an high IP69K protection degree. DOX is an ideal floodlight for use in all motor vehicles both civil (boats, cars, camper vans...) or industrial (ships, cranes, earth moving machines, bulldozers, fork lifts...) and, able to function with a flexible supply range from 9 to 30V DC that allow usage also with energy coming from photovoltaic solar panels. DOX peculiarities allow a secure use in all situations were electrical safety needs require or suggest to employ low voltage. Usage of power led sources with a lifetime rated for more than 50.000 hours and very high efficiency makes DOX a searchlight of relevant performance. The floodlight employs 12 1,2W monochromatic cool white leds, with a colour temperature of about 6500 °K, for a total power of 18W. DOX also guarantees a limited surface temperature and a cold emitted light beam, with absence of U.V. emissions. On demand DOX can be supplied for use at line voltage (220/240 V). In such case is required an external 350 mA constant current power supply to be set separately, as the waterproof model available as an accessory. Construction: die-cast aluminium body and antiscratch coated polycarbonate protection screen. DOX is also equipped with a cable tail and a malefemale couple of waterproof connectors for a quick power connection. The floodlight is supplied hermetically sealed as no maintenance is required.
The design parameter for restaurant kitchen cold store must be offered by customer: 1. Outline Dimension in metres (Length,Width,Height) 2. The main building to hold the room: steel structure,civil work structure or others. 3. Local voltage, local frequency: 380V/3P/50Hz,or others 4. The lowest and highest temperature in construction site? 5. Product type: meat, fruit,food or others. 6. Temperature of product before stored into the cold room? 7. Indoor temperature required? 8. Cooling time required? 9. Numbers of time to open and close to door per day? 10. Whether driving forklift in the room? Feature of restaurant kitchen cold store: 1. Supply power: 380V-50Hz-3P or others. 2. Temp: -40~ 20'C. 3. Copeland condensing unit or others famous brand. 4. DANFOSS pressure controller or others. 5. Size:customized. 6. PU,EPS panels,swing or sliding door. 7. Other electronic fitting. Kitchen restaurant cold store specification: 1. Refrigeration system: Compressor,Condenser,evaporator,Refrigerant. 2. Electric system: Siemens and Schneider electric components or others 3. Selection of world famous compressors, such as Bitzer, Copeland, Maneurop, Turin etc. 4. Insulation panel :use 100%polyurethane insulation panel,density about 38~46kg/m3,with gasket,with flame retardant,panel thickness:100mm~200mm, standard width of panel is 980mm. 4.1 Material:PU,EPS panel,metal sheet. 4.2 Metal sheet:Painted color steel sheet,stainless steel sheet,or other. 4.3 Thickness of panel:75mm,100mm,110mm,150mm,200mm etc. 4.4 Different temperaturer requires different thickness of panel. 5. Cold store door: a. Swing door and sliding door for choice. b. Swing door:manual opened,automatic,etc. c. Coated with stainless steel sheet,color steel sheet on the faceplate. d. Polyurethane insulation panels' material. Cold store application: food(meat, vegetable,fruit,dairy,drink),medicine,chemical,electronics,etc. functions: fresh-keeping. Freezing, quick-freezing. Fire-proof. Air-conditioning are all available. We export a compete of cold room,such as cold room panel,refrigeration unit,evaporators and so forth,they will be protected by polystyrene panels and polythene panel to prevent them damaged when they are loaded into the containers.For this,it can save space and ocean freight for you.
Description: OP-COM - PC based Opel diagnostic VERSION: OPCOM 201008 OP-COM is a PC based diagnostic program. Function: 1. It covers almost all Opel cars, even new cars with CAN-BUS based diagnostic, such as Vectra-C, Astra-H, Zafira-B. 2. The program lets you to read out and clear fault codes, shows you live data, lets you to perform output test. 3. The program supports many control units, like Engine, Automatic Transmission, ABS, Airbag, Engine Cooling module, Instrument Cluster, Electronic Climate Control, Body Control Unit, just to name a few examples. 4. Since Opel uses many pin in the OBD connector, the diagnostic interface works as a multiplexer, and selects the appropriate pin for communication. PIN3, PIN7, PIN8, PIN12 = Serial Link (ISO9141, KW81, KW82, KWP2000) 5. Fault codes will be shown with all available information: Full fault code text description: 1) Full status information (Present, Not present, Intermittent) 2) You can print out, save, or copy the fault codes to any other application. From the fault codes window, you can go directly to the measuring blocks window. 3) The program shows you measuring block information on many control module, you can choose anything from the list on your own. 4) The program is capable of showing 8 measuring block parameter simultaneously. The sample rate is depends mostly on the communication protocol. For example, older system, like Omega-B X 25 DT Engine (ISO-9141-2) can be very slow, during communication, while newer Multec, or Bosch units are faster (using KWP-2000), and the newest CAN based control units are very fast! You can also run output tests on many controllers: PIN6-PIN14 PIN3-PIN11 PIN1 HSCAN - Dual-wire, High Speed CAN-BUS, 500 kbps MSCAN - Dual-wire, Medium Speed CAN-BUS, 95 kbps SWCAN - Single-wire, Low Speed CAN-BUS, 33.3 kbps. Weight: 0.4KG.
FDV-1KW Technical Parameter: Power : 1KW Blade Height: 1.8m Material of the blades : Fiber glass-reinforced plastic Rated Wind Speed: 10m/s Cut-in Speed: 3m/s Cut-out Speed: 25m/s Security Wind Speed: 40m/s Output Voltage: 48v Working Temperature : -40--+40 Height of Guy Cable Tower: 6m Top Quality Except Tower: 120kg Generator Style: 3-phase AC PM Output Controller System: Controller , Inverter Suggested Batteries and its Capacity: 4PCS 12V100AH Can Supply Power for: Washing machine,Color TV, Lighter, Fanner, Charger 1KW OFF GRID QUOTATION. CONTROLLER & INVERTER: Model: WWS10A-48-B Rated Wind Turbine Power: 1kW Rated Solar Power: 300W Rated Battery Voltage: 48V Wind Turbine Maximum Input Current: 40A Wind Turbine Maximum Input Power: 2kW Unload Voltage factory default : 56V Unload Current factory default : 25A Control Mode: PWM Display Mode: LCD Display Parameters: Wind Turbine Power, Wind Turbine Voltage, Wind Turbine Current, PV Voltage, PV Charge Current, PV Power, Battery Voltage. Working Temperature & Humidity: -20~+50/35~85%RH Without Condensation Temperature Compensation optional : 4mV//2V ,¨C35--+80 , Precision 1 Communication Mode optional : RS232, RS485, RJ45, GPRS. Etc Protection Function: Solar reverse charge protection , Solar reverse connection protection, Battery over charge protection ,Battery reverse connection protection, Lightning protection, Wind turbine current limiting, Wind turbine automatic brake and manual brake. Model: WI10-48-S Rated Output Capacity : 1kVA Rated Battery Voltage : 48 VDC Over Voltage Shutoff: 68VDC Over Voltage Recovery: 66VDC Under Voltage Shutoff: 42VDC Under Voltage Recovery: 48VDC No Load Loss: 0.35 A Output Wave Form: Pure Sine Wave Display Mode: LCD Display Parameters: Battery Voltage, Status parameters Cooling Mode: Fan Rated Output Voltage: 110/120/220/230/240VAC Wave Distortion: 4 Output Frequency: 50/60 Hz¡À0.05Hz Dynamic Response: 5% Overload Capacity: 120% 1min,150% 10s Inverter Efficiency: Maximum 90% Noise 1m : 40dB Insulating Strength: 1500VAC,1min Protection Function: Battery over voltage protection, Battery under voltage protection, Battery reverse connection protection, Output overload protection, Output short circuit protection, Overheating protection. Working Ambient Temperature: -20¡«50 Working Altitude: 4000m Working Ambient Humidity: 0~90%,no condensing. In plywood.
1. Advanced high-titanium vitreous enamel patent discharge tube technology 2. Optimized mechanical design 3. Advanced IGBT power supply unit 4. Low harmonic pollution 5. Low energy consumption 6. High ozone concentration, strong and durable 7. Compact structure 8. Low maintenance workload 9. PLC automation, human-machine interface control 10. Large processing device, optional bus. type Ozone capacity(kg/h) Feed gas flow rate(m3/h) Ozone concentration(mg/l) Cooling water flow rate(m3/h) Power(Kwh/kgO3) Dimension (mm) Interface pipe diameter SK-CFG-1000B 1 42-56 18-24 2-3 18-20 2000×2200×1900 DN32 SK-CFG-1500B 1.5 63-84 18-24 3-4 18-20 2100×2300×1900 DN40 SK-CFG-2000B 2 84-111 18-24 4-6 18-20 2400×2600×2100 DN50 SK-CFG-3000B 3 125-166 18-24 6-8 18-20 2500×2800×2200 DN65 SK-CFG-4000B 4 167-222 18-24 8-12 18-20 3000×3000×2200 DN80 SK-CFG-5000B 5 209-278 18-24 12-15 18-20 3000×3000×2200 DN80 SK-CFG-6000B 6 250-333 18-24 15-18 18-20 3600×3000×2300 DN80 SK-CFG-8000B 8 334-445 18-24 19-24 18-20 3600×3200×2300 DN100 SK-CFG-10000B 10 417-556 18-24 25-30 18-20 3800×3200×2300 DN100 SK-CFG-15000B 15 625-833 18-24 40-45 18-20 4000×3600×2500 DN100 SK-CFG-20000B 20 834-1111 18-24 55-60 18-20 4600×3800×2800 DN100.
Industrial Evaporator industrial Evaporator can be used for low temperature continuous evaporation and concentration,and its feature is high heat transmission coeffcient and short heating time of material.It is especially suitable for materails with thermal sensitivity,viscosity,or foamability.This type of evaporator is widely applied to the industries of salt manufacturing,milk,glucose,starch,xylose,pharmacy,chemical,biological engineering,environmental engineering,waste liquid recycling and so on. Composition: The Sodium evaporator is composed of the heating evaporators for each effect,segregator for each effect,condensor,heat pressure pump,vaccum system,feed liquid conveying pump for effect,condensed water outlet pump,operating platform,control cabinet of electrical appliances,pipleline and so on. Features of sodium evaporator: 1.Due to the even heating of steam and flow evaporation of feed liquid film type,the whole heating system features high heat transmission efficiency and short heating time. Equipped with a heat pressure pump,our evaporator is energy-saving and features low steam consumption and low cooled water circulation volume. 2.The material is evaporated flowingly under increased pressure and speed, along the pipe wall from upper to down. Therefore the evaporator is suitable for materails with high viscosity. 3.Since ther material is of film evaporation in each pipe,the heating time of feed liquid is very short.Hence,our sodium chloride evaporator is perfectly suitable for the evaporation and concentraion of food,and could greatly keep the nutrients in food. 4.The evaporation is performed under the vacuum condtion,which not only meets the requirements of hygiene and environment protection,but also greatly lowers the evaporating temperature. The heat pressure pump used in our evaporator takes partial secondary steam into device again and make it mix with live steam, which greatly reduces steam consumption.The steam in the heat pressure pump sprays out like the mist and enters into the heating casing,and then spreads quickly and heats the feed liquid mildly.So our sodium chloride evaporator can be used to evaporate thermal sensitive materials. 5.This evaporation equipment is also suitable for materials with foamabilty.The feed liquid is of film evaporation in the heating tube,which forms steam-liquid separation.In addition,most feed liquid is pumped out, and only at a small amout of feed liquid and all secondary steam enter into the segregator for forced separation.There is no big impact in the whole process,which avoid the forming foam. Wooden case.
Salt Evaporator: Salt Evaporator can be used for low temperature continuous evaporation and concentration,and its feature is high heat transmission coeffcient and short heating time of material.It is especially suitable for materails with thermal sensitivity,viscosity,or foamability.This type of evaporator is widely applied to the industries of salt manufacturing,milk,glucose,starch,xylose,pharmacy,chemical,biological engineering,environmental engineering,waste liquid recycling and so on. Composition: The Sodium evaporator is composed of the heating evaporators for each effect,segregator for each effect,condensor,heat pressure pump,vaccum system,feed liquid conveying pump for effect,condensed water outlet pump,operating platform,control cabinet of electrical appliances,pipleline and so on. Features of sodium evaporator: 1.Due to the even heating of steam and flow evaporation of feed liquid film type,the whole heating system features high heat transmission efficiency and short heating time. Equipped with a heat pressure pump,our evaporator is energy-saving and features low steam consumption and low cooled water circulation volume. 2.The material is evaporated flowingly under increased pressure and speed, along the pipe wall from upper to down. Therefore the evaporator is suitable for materails with high viscosity. 3.Since ther material is of film evaporation in each pipe,the heating time of feed liquid is very short.Hence,our sodium chloride evaporator is perfectly suitable for the evaporation and concentraion of food,and could greatly keep the nutrients in food. 4.The evaporation is performed under the vacuum condtion,which not only meets the requirements of hygiene and environment protection,but also greatly lowers the evaporating temperature. The heat pressure pump used in our evaporator takes partial secondary steam into device again and make it mix with live steam, which greatly reduces steam consumption.The steam in the heat pressure pump sprays out like the mist and enters into the heating casing,and then spreads quickly and heats the feed liquid mildly.So our sodium chloride evaporator can be used to evaporate thermal sensitive materials. 5.This evaporation equipment is also suitable for materials with foamabilty.The feed liquid is of film evaporation in the heating tube,which forms steam-liquid separation.In addition,most feed liquid is pumped out, and only at a small amout of feed liquid and all secondary steam enter into the segregator for forced separation.There is no big impact in the whole process,which avoid the forming foam. Wooden case.
Brine Evaporator: Bine evaporator can be used for low temperature continuous evaporation and concentration,and its feature is high heat transmission coeffcient and short heating time of material.It is especially suitable for materails with thermal sensitivity,viscosity,or foamability.This type of evaporator is widely applied to the industries of salt manufacturing,milk,glucose,starch,xylose,pharmacy,chemical,biological engineering,environmental engineering,waste liquid recycling and so on. Composition: The Sodium evaporator is composed of the heating evaporators for each effect,segregator for each effect,condensor,heat pressure pump,vaccum system,feed liquid conveying pump for effect,condensed water outlet pump,operating platform,control cabinet of electrical appliances,pipleline and so on. Features of sodium evaporator: 1.Due to the even heating of steam and flow evaporation of feed liquid film type,the whole heating system features high heat transmission efficiency and short heating time. Equipped with a heat pressure pump,our evaporator is energy-saving and features low steam consumption and low cooled water circulation volume. 2.The material is evaporated flowingly under increased pressure and speed, along the pipe wall from upper to down. Therefore the evaporator is suitable for materails with high viscosity. 3.Since ther material is of film evaporation in each pipe,the heating time of feed liquid is very short.Hence,our sodium chloride evaporator is perfectly suitable for the evaporation and concentraion of food,and could greatly keep the nutrients in food. 4.The evaporation is performed under the vacuum condtion,which not only meets the requirements of hygiene and environment protection,but also greatly lowers the evaporating temperature. The heat pressure pump used in our evaporator takes partial secondary steam into device again and make it mix with live steam, which greatly reduces steam consumption.The steam in the heat pressure pump sprays out like the mist and enters into the heating casing,and then spreads quickly and heats the feed liquid mildly.So our sodium chloride evaporator can be used to evaporate thermal sensitive materials. 5.This evaporation equipment is also suitable for materials with foamabilty.The feed liquid is of film evaporation in the heating tube,which forms steam-liquid separation.In addition,most feed liquid is pumped out, and only at a small amout of feed liquid and all secondary steam enter into the segregator for forced separation.There is no big impact in the whole process,which avoid the forming foam. Wooden case.
Introduction: A-Polylysine, a kind of peptide with a linkage between a£carboxyl group and examine group, is a natural substance from microbial metabolism. It has lots of advantages over traditional preservatives, such as high safety good heat tolerance and solubility in water and extensive antimicrobial against Gram+, Gram- bacteria and fungi. Now it has been applied extensively in food and pharmaceutical industry for the wide range of antimicrobial spectrum. Physical properties: A-Polylysine is the polymer of L-lysine. It is slightly bitter, hygroscopic, light yellow power. It is soluble in water, slightly soluble in ethanol. The 30-unit homopolymer has a molecular weight of 4700 and an empirical formula of C180H362N60O31. It is still stable when heated (12020min or 100,30min). It inhibits the thermophilics. So it is also applied to high temperature process. The activity of A-Polylysine decreases at the presence of acidic polysaccharide, chloride, phosphate, and Cu2+ while its activity increases with presence of hydrochloric acid, citric acid, malic acid, glycine and glyceride. Safety: A-Polylysine is recognized as a very safe substance in the scientific community. A-Polylysine was generally recognized as safe as food preservative by FDA in October, 2003.It had been approved by FDA for use as an antimicrobial agent in cooked rice or sushi rice at levels up to 50 milligrams per kilogram (mg/kg) of rice. The results of an acute toxicity study and bacterial assays for mutagenicity shows that A-Polylysine was non-toxic and there was no evidence for mutagenic activity of A-Polylysine. So A-Polylysine is absolutely safe to be used as food preservative. Quality Standard: FAO/WHO 1992 1. Content 95 2. Loss on drying 1053h 20 3. Heavy metalCalculated as Pb 20ppm 4. Loss on ignition 1% Application: A-Polylysine has already been used generally as a food additive recognized its safety and advantage in Japan and Republic of Korea. Moreover, A-Polylysine is acknowledged as a world standard food additive by this recognition of A-Polylysine as a GRAS material of FDA in US. A-Polylysine has a function to prevent a microbe from proliferating by ionic adsorption in the microbe. By such excellent properties as various antibacterial properties and properties not to destroy flavor, polylysine has been used mainly as what improves in keeping quality of food and applied to a box lunch and prepared foodstuffs in a convenience store or the like. It can be used in rice, noodles, cakes, snacks, and ice creams, salad, canned foods and meat products. In addition, A-polylysine is used in SAP to produce sanitation products, such as sanitation napkin and diapers because of its good absorption of liquid. It can also be used as a carrier for pharmaceutical molecules. Moreover, even in a field other than food, taking advantages of characteristics of polylysine, the application to fiber, processed goods, and cosmetics as an antibacterial agent excellent in kitchen and bath room application has also been developed. Storage: Be laid in dry, shady and cool place with sealed packing. 0.5kg, 1kg,5kg or packed to customers requirements.
1.Function and using range: This product is a kind of solid enzyme which is extracted from Bacillus subtilis which is deeply fermented. It can hydrolyze the macromolecular protease to amino acid,etc.Meanwhile,it is used to remove the fur, soften the skin, remove glue of the silk, reclaim film and medicine,etc. 2.Define of enzyme activity: In the case of 30 centi degree and PH:7.5,the speed, using 1g solid enzyme powder to hydrolyze casein can produce 1ug tyrosine in one min,is defined as enzyme activity(u/g). 3.Product specification and package: This product is powder. content of water is below 6 percent. internal package:2kg,and external package:20 or 30 kg.enzyme activity:50000u/g. 4.Product standard: It accords with business standard of QB1805-93 of people republic of China. 5.Using condition: The best temperature:35-45 centi grade The best PH:6.5-7.5. 6.Adding amount and using methods: 1. Used in removing fui of feather, removing fui with enzyme(35-4235-42pH7.520-25u/ml)-wash-dip acid. 2. Usd in reclaiming file.45 centi grade,PH7.0-7.5,20-23u/g 3. Used in removing glue of silk: advanced dissolve-remove water-acid disolve(protease 18-24u/g,soap 0.75%,48-50¡æ30-60minutes,PH7-8)-remove water-pull skin-wash-remove water-shake-bake-shake. 4. Used in medicine: it can be used to treat chronic bronchitis,cough,etc. 5. Used in feed: it can be mainly used together with amylase, acid protease, cellulose enzyme, sugar enzyme,etc.It can be expansively used in the feed of pig, fish and other animals. After this enzyme is put into the feed, you can well control of the temperature, moisture, PH and working time in order to dissolve the material in the function of this enzyme. If you feed animals in a small scale, you can add the enzyme directly, and stir sufficiently, and then feed animals. Generally the proper amount is 0.1-1.0 percent compared to the feed. 7.Storage and transportation: This product is a activated substance, which should be put in cool, dry place, and avoided strong sunshine,heat,moisture.In the transportation, you should avoid strong shining and raining them. In the event of 25 centi degree, enzyme activity can be well kept over 85 percent in six months. 1kg/bag
Product presentation: Beer complex enzyme which is independently combined by our corporation consists of some kinds of excellent enzyme which is used in beer brewing industry, including Beta-amylase,Xylanase,Cellulose,Neutral protease, Middle-temperature Alpha-amylase,etc Through many experiments and pilot plant test, the proportion of combination is very reasonable and efficient, and can exert their function of all kinds of enzyme preparation. It has been used expansively in beer brewery, which has obtained good result. Specification: One kg per bag(Aluminum foil bag) 20kg per barrel. Beta-dextranase:5600 IU/g Xylanase:2600 IU/g Cellulose:2200 IU/g. Neutral protease:35000 u/g Middle-temperature Alpha-amylase:1500 u/g. 98 percent can pass 80 meshed normal sieve. Using methods: Recommended amount of beer saccharification is 200-500 g per ton malt This beer complex enzyme mainly used in the process of saccharification of material which contents 10-40 percent of malt. In the event of high-concentrated glycation and using numerous national malt, the best using amount is 300-600 g per ton malt(net weight). If the result of glycation is very good, you can properly reduce the using amount. This enzyme can be added after material has been put into mesh copper. This enzyme can be directly put into mesh copper. Using condition: PH range: proper PH:3.6-6.5, the best PH:5.5. Temperature: proper temperature:40-75 centi grade,the best:65 centi grade. Using result: It is mainly used in the process of saccharification of beer brewing to improve and raise result of glycation. 1. It can validly decompose Xylanase,Beta-dextranase,reduce viscosity of malt juice, increase malt juice and beer¡¯s filter efficiency and quality. 2. Improve receiving rate of malt juice. 3. Decompose protease, improve content of Alpha-amino nitrogen and dissolved nitrogen in malt juice. 4. Improve washing result of filter, boiling machine 5. Increase amount of filtering beer each time. 6 Avoid validly turbidness to improve beer non-biological stability. Storage and transportation: This product is a kind of active substance, which should be put on the cool, dry place, avoiding strong shine,heat,moisture.If can be well kept six months below 25 centi grade, one year below four cent grade.
Super glue is a single-component cyanoacrylate monomer in the liquid state, capable of extremely rapid polymerization between adherent surfaces, result-ing in extremely strong and structural bonds at room temperature. This instant adhesive will, with only normal surface preparation, bond all materials commonly used in the engineering industry, except polyethylene. Polypropylene, teflon, and very porous surfaces, which require special treatment. To open tube: 1. Unscrew entire nozzle & cap unit. 2. Reverse cap and place pointed end on top of tube. Point tube away from face, Press to puncture. Do not squeeze tube while puncturing. After puncture is made, replace nozzle & cap. 3. Unscrew outer cap only and apply sparingly. Clean tip after each use. Application: Be sure both surfaces are clean and dry. Apply with extreme care. Never spread with fingers. Apply one drop for each 3 cm area. Apply to only one of the surface, Quickly place two surfaces together with slight finger pressure. Bond is completed in seconds, or depending on material in about one minute, leave for 24 hours for strongest bond. Clean away all excess adhesive from container with ties-sue paper. Keep out of reach of children, in cool dry place. Warning: Keep out of reach of children: Adhesive will stick to skin very quickly, when using, be sure it dose not come into contact with fingers, do not try to pull it off. Soak fingers in warm water and work off Nail polish remover may also be used. If adhesive get in eye, wash eye with quantities of plain water, do not try to remove by rubbing or applying solvents, in case of pain or discomfort, consult a doctor. Bond for home uses: For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper. Application suits for metal, rubber, ceramics, plastic, wood. Appearance colorless transparent liquid Specification 3 gram/tube,12 tubes/blister card. Packing 72 card/carton Measurement(cm) 57*28*38 1 container 20 feet 465 cartons 1 container 40 feet 960 cartons G.W/N.W(KG) 11 KG/10 KG Shelf Life 12 months.
Features: 1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones 2, No need to wet the brick wall, effectively improve the efficiency 3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall 4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function 5, Small shrinking rate, no cracking, can be used in cold and humid environment. Application: 1, The adhesive for cement plaster, brick, smooth cement wall paste stone 2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Operation Process: 1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect 2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Normal Amount: Coverage areas differ according to the circumstance: 1, using 3*3mm tooth scraper about 1.8kg/m2 2, using 6*6mm tooth scraper about 3kg/m2 3, using 10*10mm tooth scraper about 4.8kg/m2 Note: the amount is related to the smooth, vertical rate, and thickness of the stone material Cautions: 1, make sure the smooth and vertical rate of the surface before operation 2, never mix the dry slurry with water and use again 3, for the painting surface, make sure the initial bond strength and no flake 4, Finishing after 24h can be walked in or fill the crack. Store Method: Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
Features: 1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones 2, No need to wet the brick wall, effectively improve the efficiency 3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall 4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function 5, Small shrinking rate, no cracking, can be used in cold and humid environment. Application: 1, The adhesive for cement plaster, brick, smooth cement wall paste stone 2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Operation Process: 1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect 2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Normal Amount: Coverage areas differ according to the circumstance: 1, using 3*3mm tooth scraper about 1.8kg/m2 2, using 6*6mm tooth scraper about 3kg/m2 3, using 10*10mm tooth scraper about 4.8kg/m2 Note: bricks for wall using 3*3mm tooth scraper or 6*6mm tooth scraper, bricks for floor using 6*6mm tooth scraper or 10*10mm tooth scraper. Cautions: 1, Make sure the smooth and vertical rate of the surface before operation 2, Never mix the dry slurry with water and use again 3, For the painting surface, make sure the initial bond strength and no flake 4, Finishing after 24h can be walked in or fill the crack. Store Method:Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
General: Rustoper (corrosion terminator) VCI paper is made and refined from excellent antirust base paper and high efficient and compounded special VCI LIQUID with specific production technology. In the confined space with sealed packaging, VCI contained in the paper begins to sublimate and volatilize the antirust gas factors which diffuse and penetrate into the surfaces of the articles for antirust and adhere on them to form a compact protection film with the thickness of monomolecular, thus the corrosion is effectively prevented. Features/Advantages: 1. The paper makes oil-free packaging available, and no coating, degreasing or cleaning procedure is required, which saves labor, time and cost. 2. VCI with high performance contained uniformly in the antirust paper will play a role of antirust soon after it is sealed in a package. 3. Even if the paper does not contact the metal directly, it can effectively perform the function of antirust, so it is especially applicable to metal products with complex appearance. 4. The paper has both functions of antirust and packaging. 5. The paper has the advantages of low cost and easy operation over vacuum package. 6. The paper is clean, harmless and non-toxic, so it is safe to environment. It passes SGS certification and meets RoHS directives. Applicable Metals: The VCI paper is applicable to ferrous metal, alloy steel, cast iron, copper, brass, bronze, plated metal, zinc and its alloy, chrome and its alloy, cadmium and its alloy, nickel and its alloy, tin and its alloy, aluminum and its alloy, and other metal materials and their products. Application Method: 1. The antirust paper shall contact the articles for antirust as closely as possible, without any barriers between them. 2. Before being packed, the surfaces of the articles for antirust shall remain clean and dry without impurities on them. 3. In case the surfaces of the articles for antirust are regular in their shape, the articles can be completely covered individually with the VCI paper (the utilization area of VCI paper shall be about the same as the surface area of the article) and then their joints shall be sealed. VCI paper can also be used as inner lining or interlayer packing paper in a sealed packaging unit (container, plastic bag, etc.). 4. Operate with clean gloves, and do not contact the articles for antirust with naked hands. Period of Antirust: One~three years (use according to required specifications) Custody and Storage: With sealed package, it shall be kept in a cool, dry place, away from sunshine and no contact with sources of ignition and corrosive materials. The quality guarantee period shall be twelve months from the date of delivery. FE film+Kraft paper+CPP.
Fiber Laser Marker Principle Fiber laser adopts a fully integrated design and merges all the components into a single fiunctional element. It has no optical power coupling loss and pollution, air cooling. It possesses merits of high efficiency, long lifetime and low maintenance. Features Excellent beam quality The beam quality of GD-FM Series Fiber laser marking machine is better than that of the conventional solid-state laser marking machine. It is output from the base model (TEMOO) and the focused spot size is 10um. And its divergence angle is 1 / 4 of the semiconductor pump. So it is especially suitable for precision and fine marking. Low utility cost The maximum photoelectric efficiency is up to 30%. The input power of this equipment is less than 500W which equals to 1/10 of lamp pump YAG laser marker and saves lots of energy consumption expense Zero maintenance Lightstar Fiber Laser Marker is maintenance free and unnecessary to adjust or clean lens. Long lifetime Fiber Laser Marker adopts laser diodes as pump source, its average working time can reach 100,000 hours. High processing speed The processing speed is 2-3 times faster than traditional laser marker. Applications Electrical appliances, electronic communications, auto parts, precision metal, jewelry gifts, glasses watches, instrumentsation, and bathroom ware etc Fiber laser marker specification Technical parameter Average output laser power : 5,10 ,20 or 30W (continuous or Pulse) Laser wavelength : 1064nm Power adjusting range : 10-100% Repetitive frequency : 20-100KHz Beam quality£¨M2£© : 1.4-1.8 Optical-electronic efficiency : 30% Marking range : 100X100 mm Marking depth : 0.01-0.2mm Min focus spot size : 0.01mm Min. character height : 0.2mm Repetitive accuracy : ¡À0.001mm Max. liner marking speed : ¡Ü7000mm/s Marking format : Figure, word, bar code, 2D, Date, shift, batch no, seri code, date, order of runs, lot number, serial number, file chaining Operating system : Support PLT¡¢DXF¡¢BMP ,SHX, TF library using SHX¡¢TTF character storage directly Dimensions (L*W*H mm) : 550¡Á900¡Á1200 Power requirement : 220V£¬50Hz/60Hz. Wood packing.
