By the Vibrating feeder, the material will be fed evenly and continuously into the room of the Storage Bin to grind. In the production line, the Vibrating Feeder can evenly feed the crushing material, and complete the primary screening. Vibrating Feeder features its own superiorities: stationary vibration, reliable operation, long time service life. The vibrating force can be adjusted, and the flux can be randomly changed and controlled, very convenient to control. The vibration force is the source of vibrating motor. It is of low noise, low energy consumption, good performance. Vibrating feeder is of simplicity in structure, reliability in operation, convenience in adjustment, light in weight, small in size, convenience in maintenance. The dust contamination can be prevented when the closed structure is adopted. Model:GZD-180*80,GZD-200*120,GZD-300*90,ZSW-380*96,ZSW-420*110,ZSW-490*110,ZSW-490*130,ZSW-600*150. Capacity (t/h): 30-80,80-500,40-100,90-200,150-350,180-380,250-450,450-800,600-1000. Max.Feed Size(mm):300,300,300,500,580,580,750,800.
Sand Washing Machine is also called Sand Washer, Washing Machine, Wash Equipment, Sand Gravel Washer , Sand Cleaning Machine, Sand Washing Equipment, Sand Cleaning Equipment. XSD series High-efficient Sand Washing Machine, which is used for washing away the stone power and impurity in the sand made by the Sand Making Machine, to increase the sand quality, is a necessary equipment to wash sand in coordination with the sand making machine. XSD series high-efficient Sand Washing Machine, on basis of the practices in sand and stone industry, designed by our professionals. This series product possesses the good qualities that high cleaning, reasonable structure, high capacity, energy saving, low sand loss. The special design for the transmission part separating with water and sand enables its low maintenance. It is the best choice for our customers. It is always used in washing, grading and dehydrating quartz and sand in Construction Site. Sand stone Factories, Hydropower Station and Concrete Dam Site, Pre cast Concrete Factory, Glass Factory and etc. Models: XSD2610, XSD3016,XSD3620 Impeller Specification (mm) (D,W): ¦2600,1000, ¦3000,1600,¦3600X2000. Capacity (t/h): 20~50, 50~120,120-180 Feed Size (mm): ¡Ü10, ¡Ü10,¡Ü10 Overall Dimensions (L,W,H): 3320,2125,2670, 3810,2686,3085,4500,3206,3480.
Efficient crushing-type mills are widely used in metallurgy, mining, chemical, cement, coal gangue, construction, sand, refractory material, ceramic and other industrial and mining enterprises, engaged in breaking and crushing the material in the operation. It is mainly suitable for crushing various soft and hard ore. whose compression strength is not higher than 320MPa (MPa) Features: 1. High production and high crushing ratio. 2. Low power consumption, homogeneous particle size. 3. Simple, compact and light mechanical structure. 4. Low investment cost, easy management. Structure and working principle£º: Efficient crushing mill consists mainly of frame, rotor, hammers and grizzly bars and other components. The frame includes upper part and lower parts, which are welded by steel plates after cutting, the remaining parts bolted into one. High manganese steel liners are studded with inside the frame, to facilitate replacement for a new liners after worn; on the main shaft are installed several groups of the spindle distribution of the hammers, which consists of rotor with the axle of hammers and rotary table. The host drives the main shaft through the motor and V-belt driven spindle to rotate the rotor, generating the centrifugal force, then driving all hammers stretch around. The bulks of material feed into the crushing chamber, will be crushed by the hammers at a high-speed movement. The broken material requested will be passed the grizzly bars at the lower part and discharged, the unbroken rest will be left in the chamber to be crushed repeatedly by the hammers and iron plates until it can reach the requested standard. To avoid clogging, the water content of the material to be crushed not more than 5%. The performance parameters of efficient crushing-type mills: Model PC4008-75 PC4012-90 PC4015-132 Diameter of the rotor (mm) 750 900 1150 Length of the rotor(mm) 800 1200 1500 Rotation speed of the rotor (r/min) 800-1000 800-1000 700-1000 Max. input size(mm)
Vibrating Screen is also called Vibratory Screen,Vibrosieve, Screen, Circular Vibration Screens, Sieve, Sieving Eequipment, shaking screen, Inclined Screen,Circular Vibrating Screen,Vibrating Riddle, Screen Machine. For Vibrating Screen, the amplitude can be adjusted. It is of long screening line, multi-layers screen, correct to screen in all kinds of specification ,high efficiency in screening, so widely used in mine selection and sand stone crushing. Model:2YA1237,3YA1237,2YA1548,3YA1548,2YA1848,3YA1848,2YA1860,3YA1860,4YA1860,2YA2160,3YA2160,4YA2160,2YA2460,3YA2460 Spec.of Screen: 1200*3700 mm,1200*3700,1500*4800,1500*4800,1800*4800,1800*4800,1800*6000,1800*6000,1800*6000,2100*6000,2100*6000,2100*6000,2400*6000,2400*6000 Layers: 2,3,2,3,2,3,2,3,4,2,3,4,2,3 Sieve Pore Size(mm): 3-50,3-50,5-50,5-50,5-80,5-80,5-80,5-80,5-80,5-100,5-100,5-100,5-150,5-150 Max. Feed size: 200 mm,200,400,400,400,400,400,400,400,400,400,400,400,400 Capacity: 7.5-80,7.5-80,50-208,50-250,50-260,50-300,50-300,50-350,50-350,100-500,100-500,100-500,150-700,150-700. Trademark: SHIBANG Standard: ISO9001:2000 Unit Price/Payment: TT/LC.
Detailed Product Description: Ball mill is widely used for milling various kinds of ores or rocks in metal and non-metal mining and building material industry.The main bearing of the ball mill with the shell diameter 900-2100mm is spherical liner bearing; for the shell diameter 2700mm,the main bearing is completely closed self-aligning 120,bearing withBabbitt alloy of high lead and low tin with low hardness,underneath laid withcooling copper piping full of water The bearing is of static pressure structurewith high and low pressure united oil lubricating system. Our Ball Mill is the key equipment for grinding after the crush process, which is widely used in the manufacture industries, such as cement, silicate, new building material, refractory material, fertilizer, ferrous metal, nonferrous metal and glass ceramics and can be used for the dry and wet grinding for all kinds of ores and other materials able to grind. The Ball mill Model: §¶1830*3000,§¶1830*6400,§¶1830*7000,§¶2200*5500,§¶2200*6500,§¶2200*7500 Weight of ball mill:11£¬23£¬25,30,30,23.
Gypsum block production line of high quality, best price.
Capacity: 30,000 ton/year~240,000 ton/year Automation: fully automatic Calcination system: using boiling furnace to calcine, adopting heat conductive oil furnace as heat source Fuel: coal, natural gas, heavy oil, diesel oil. Packaging Details: wooden case packing /20 'container / 40 'container.
The parameters of the gypsum board production line are as follows: 1) Production capacity: 2 million ~20 million square meter per year. 2) Final product variety: common paper-covered, plasterboard fire resistance, paper-covered plasterboard, water resistance paper-covered plasterboard. 3) Product specification: thickness from 7mm ~ 15mm, length from 2400mm ~ 3000mm, width from 1200mm ~1220mm 4) Product quality: in conformity with standard of P.R.C gb/t9775-2008 paper-covered plasterboard. Wooden case packing /20 'container / 40 'container.
The paper faced gypsum board production line is the professional equipment for producing the new decorated material. The principal working process are as follows: first, we take certain amount of hemihydrate gypsum powder, water and other additives, through the automatic measurement device and automatic conveying system, they will be conveyed into the mixer and changed into the gypsum slurry which will be scattered on continuous moving faced paper evenly. Second, at the same time, with the continuous moving and vibrating, the slurry will gradually diffuse and even scattered. Then the slurry will go into the forming machine and compound with the top and bottom faced paper. By the process of extruding and forming, the slurry will be encased by the faced paper and the continuous pulpous gypsum boards are formed. Third, In the forming line, the wet solid paper faced gypsum board will be gradually formed after the process of recondition, natural coagulating, automatic cutting, etc. The wet board will be arranged according to the programmed control system. With the help of rollers, belt conveyer and overturner, they will quickly enter into the dryer. Fourth, the board will be strictly controlled in the separate temperature zone of the dryer. After blowing into different thermal hot air, the moisture of the wet board will be evaporated. Because of the reaction of the starch, the board will be attached to the faced paper, and then the dry gypsum board will form and exit from the dryer. Moreover, after passing though overtuner and the folding device (the front side is inside) for the second time, the board will be cut into certain specification by saw. Finally, the finished gypsum board will be conveyed to the automatic sealing device and the stacker. After the stacking, the board will be transported to the finished products warehouse by the forklift. 40 feet container for transportation.
gypsum powder machine The big sized gypsum stones are crushed into granules which are less than 25mm by the crusher. After storing and conveying, they will be conveyed into mill for grinding.Then they will be classified through a analytical engine. The qualified powder will be conveyed to the calciner for calcination, while the unqualified one will return to the mill for further grinding until it is qualified. The calcined gypsum powder (it¡¯s usually called Plaster of Paris) will be stored in the finished product silo for the preparation of plasterboard raw material or directly packing and transport to the customer;s site. There are two types of the gypsum powder productionline. One uses the direct burning calciner (it is usually used in the small capacity line, such as 20000 or 30000 tons per year), the other uses the fluidized bed furnace (it fits for all the capacity of the gypsum powder line. This style is very popular in the gypsum powder industry.). Use 40 feet container to transport.
1. PVC film lamination machine Usage and Characteristics The lamination machine is used to paste the decorative film and boards together. First, put the board on the rollers. After the dust collection process, coat the glue on the boards, the glue will be qualitatived after conveying on the guide rollers. Then it will be combined with the film and enters into the recombination mechanism. After passing and cyclic rolling of the two lines of press roller, pinch roller and forming roller, the recombination is finished. The machine is fit for the surface decorative materials, such as pasted and compound decorative film and decorative paper, etc of the PVC baseboard, profile, low foaming board and wood board, etc. Specification: Max lamination width: 1300mm Max lamination speed:2-15m/min The thickness of the laminated board: 2-50mm Transmit power: 4.50kw Power: 380V,50HZ(can be made according to the inquiry) Size: 12600*1950*1600. 2. aluminum film lamination machine Usage and Characteristics The lamination machine is used to paste the decorative film and boards together. First, put the board on the rollers. After the dust collection process, coat the glue on the boards, the glue will be qualitatived after conveying on the guide rollers. Then it will be combined with the film and enters into the recombination mechanism. After passing and cyclic rolling of the two lines of press roller, pinch roller and forming roller, the recombination is finished. The machine is fit for the surface decorative materials, such as pasted and compound decorative film and decorative paper, etc of the PVC baseboard, profile, low foaming board and wood board, etc. Specification: Max lamination width: 1300mm Max lamination speed:2-15m/min The thickness of the laminated board: 2-50mm Transmit power: 4.50kw Power: 380V,50HZ(can be made according to the inquiry) Size: 12600*1950*1600. It uses 40 feet containers to transport.
Gypsum powder equipment is composed of elevating system, dust collecting system, conveyor system, heat supply system, milling system etc.. And the heat supply system is the key link of the whole gypsum powder production line. The gypsum produced by our company has the following characteristics: 1.The equipment has small volume but large yield. 2.The equipment with easy structure can not be damaged easily. 3.The compact equipment covers less area. 4.It has comparative less energy consumption. 5.It can be conveniently operated and easily controlled. 6.The products are of good quality and gypsum of Paris is of ideal components and stable physical properties. 7.The capital construction investment is small and operating expense is low. Container.
Gypsum board production line. High quality, best price.
Fragmentizer large gypsum ore broken into less than 25mm of small particles through storage and transport into the mill for grinding, grinding, after an analysis machine to achieve the required fineness of the gypsum product starch into boiling furnace to calcine, the rest of the mill for further grinding until the return pass. Calcined gypsum powder sent to guessed eligible deposit or into storage products workshop .
Model : SC-60 Plate size L*W (mm) : 510*350 Max traveling speed (m / min) : 20-25 Limited grade ability : 20 Frequency (rpm) : 5600 Impact force (KN) : 10 Engine model : S20 5.0HP Starting system : Recoil starter Packing size (L*W*H) mm : 790*400*640 Net weight (KG) : 60. 790*400*640mm, 60KG.
TOPALL (CHINA) Concrete Batching Plant, Model HZS30F FULLY AUTOMATIC) This is fully automatic model of 30 cbm/hr batching plant, which with 1.500 Liters of Mixer of 3.8 meter discharging height and pneumatic controlling discharging gate. 2.4-Bin batching machine with 1200 liters weighting bucket. 3.Cement Scale. 4.Water loading is controlled by weighting measuring. 5.2*2 meter operating room. 6.Fully automatic operating system. The Fully Automatic Batching Plant, updating from the normal model, has new features. •Additive Scale. •Water Scale (By weight measurement) •Full automatic system, which can be connected with a printer and also compatible with computer.Computer and printer are optional parts, but the system can be operated without it. JS500 Discharge Capacity…500 Liter Charge Capacity……800 Liter Mixing Time ………36-45 Second Rated Output…….. 30 Cbm/hr Motor Power……… 18.5KW Hoisting Power…….5.5KW Pump Power………..0.75 KW Max diameter of aggregate….60/80 mm Gravel Crushed Stone. Total Weight……………. 4100 Kg PLD 1200 IV FOUR BIN BATCHER Storage Bin Capacity……. 4*4 Cubic Meter Weighting Capacity……… 1200 Kg. Total Power Motor………. 11 KW. Total Weight………….. 5480 Kg. SCREW CONVEYOR Conveyor Length……12000 mm Diameter………….219 mm Motor Power……….11 KW Screw Turning Speed…. 286 r/min Total Weight……….. 780 Kg CEMENT FEEDER Capacity…….1650 Kg CEMENT WEIGHTER Capacity……. 1650 Kg COMPRESSOR Type Model….. V-036/8 Discharge Volume…. 0.36 m3/Min Rated Pressure….. 0.8 MPA Motor Power……. 3 KW ADDITIVE SYSTEM Weighting Hooper Capacity… 25 Liter Additive Tank Capacity….. 1500 Liter Motor Power….. 3 KW CONTROL SYSTEM Type/Model…… PLC 30 Full Automatic WATER MEASURING SYSTEM Capacity….. 150 Liter. Motor/Pump Power….. 1.1 kw NOTE: THIS PLANT HAS WATER MEASURING BY WEIGHT SYSTEM. OPERATORS ROOM Installed Height from ground…. 2000 mm.
1 Output: Standard brick 240-115-53mm 5760/h Hollow brick 390-190-190mm 900/h Multihole brick 240-115-90mm 3240/h 2 ISO9001 3 semi-automatic brick machine 4Hydraulic, easy operation 5 Place of origin: China 6Maximum pressure: 10tons 7 models: JF-QT1500D 8 Size of bamboo pallet 1100-570-20mm 9Overall dimension 3970-1830-2350mm 10installed capacity 24.2kw 11use ground area at least 3000 square meters 12Amplitude 15mm 13produce time 8 seconds 14Frequency of shock 6500time/minute.
Dimension L x W x H 4,600 x 1,800 x 1,300 (mm) Production Capacity 5 - 8 (tons / hr ) (Adjustable by frequency converter) Degree of Vacuum ¡Ü - 0.092 (Mpa) Augers Nominal Diameter ¡é400 / ¡é300 (mm) Extruding Pressure 3.0 (mpa) (Main / Vacuum Pump) Motor Power 37 / 5.5 (kw) Weight ¡Ö 6000 (kg) Features of Type TL-CXJ-300B 1. Leading technology specially made for high-grade extruded wet-forming ceramic tiles and bricks, especially for making the split tiles, roofing tiles, special shaped tiles and clay bricks etc. 2. Casting-steel-structured machine body, high strength gear-box, special alloy steel augers etc., to ensure high quality and reliable of production. Wooden frame bottom support.
Dimension L x W x H 2,838 x 1,724 x 1,540 (mm) Working Frequency ¡Ý70 (times/min) (Adjustable) To Be Split Tiles Size L x W£º(~300) x (~200 ) (mm) (Adjustable) Main Power 1.9 (kw) Weight ¡Ö 1500 (kg) Features of Type TL- PZJ-AT The type TL- PZJ-AT of leading technology specially made for the high efficient and auto-splitting process, by which the wet-forming co-extruded double-piece split tiles being split to separated pieces of final split tiles in up to 70 times per minute working frequency and beyond 99.5% qualified rate. Wooden bottom frame.
The Clay Supply Machine consists of four parts: storing, driving, transporting and crushing. It is used with bulldozer to store clay and feed clay continuously.
