MSH Split Case Pump Size (discharge): 1 inch to 32 inch Capacity: 3.4~ 15000 m3/hr Head: 8.6~140m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc MSH Split Case Pump Introduction: MSH Split Case Pump is Horizontal, Split-casing, and Double-suction centrifugal water pump. Double Volute casing is used to contract the axial force due to high head to extend the serve lift time of bearing. Because of the short distance of two bearing, the shaft is shortened to avoid much vibration.. Closed and Circulated cooling system is applied within the sealing house.The Shaft sleeve and O-ring are used to avoid any connection between the shaft and fluid. MSH Split Case Pump Features: Both inlet and outlet of this pump are placed under the axial line,, the pump casing is opened in the middle so it is unnecessary to remove the water inlet and outlet pipelines and motor.if repaired The pump moves CW viewing from the motor side. The pump moving CCW can also be made . Both pump casing and cover form the working chamber of the impeller and there are threaded holes for mounting vacuum and pressure meters on the flanges ant both inlet and outlet have water draining plug on the lower side of flange The impeller is static-balance and dynamic balance tested, fixed by the the side nuts and the Shaft sleeve nuts and its axial position can be adjusted via the nuts and axial force will be get balanced by means of the symmetrical arrangement of its blades, there may be residual axial force which is borne by the bearing at the axial end. This pump shaft is supported by two centripetal ball bearings, which are mounted inside of the bearing chamber on both ends of the pump and lubricated with grease. The double suction seal ring is used to reduce the leakage.. This pump is driven directly via flexible coupling.(V-belt driving will be available if required). The shaft seal is mechanical seal or packing seal . MSH Split Case pump Parameter Selection Table: Pump model Capacity(m3/h) Head(m) Speed(rpm) Power(KW) MSH150 112--220 35--84 2900 30--55 MSH200 160--351 31--100 2900 37--110 MSH250 324--612 8.6--65.1 1450 22--132 MSH300 504--1663 8.7--140 1450--1470 22--680 MSH350 745--1570 10--125 1450--1470 55--630 MSH400 900--1620 32--85.5 980--1480 440--500 MSH500 1150--3800 10.6--108 740--970 110--800 MSH600 2300--4000 13--80 730--970 145--730 MSH700 2111--4896 39.5--99.5 742--980 397--1252 MSHS800 3960--6878 23--84 600--750 450--1600 MSH1000 6600--9900 32--52 600 1250 MSH1200 5832--14400 6--95.7 500--745 710--3450 MSH Split Case pump On-site Application: MSH split case pump is suitable for transporting pure water or liquids with physical and chemical properties to water. Suitable for mine Suitable for water supply and drainage in factory. Suitable for power station. Suitable for urban water supply and drainage Suitable for flood control.
Dc/ac motors I am an exporter in line with dc/ac motors from china for several years.I have special ac/dc motor manufacturer , dongyang dongzheng motor coporation, ltd, who has passed the iso9001:2000, ccc and ce certification.Their products inchudes ac/dc gear motors, worm gear motors, brushless motors, planetary gear motors, etc.With the rich experience on the motor, i will supply you favorite motors with excellent quality but at the most resonable price.I hope we can start a pleasant cooperation! Diverse, according to your request
material: steel(Gcr15) core size:20mm out diameter:47mm width:14mm Radius:1.0mm Dynamic load;12.8KN static load:6.65KN rotating speed: 14000 grease/18000 oil ball qty:8 weight:106g
Three Phase Induction Motor Speed Controller Trainer - BRAND - VIJAYANTA, INDIA 1. Study of Three Phase Induction Motor Speed Controller Trainer, With motor generator set, DC shunt generator, 1 KW, AC Sliping Motor 1 HP., Model: TPAC â?? 401 Suitable for to study speed control of three phase induction motor using Three phase AC Voltage Controller.
Warranty: 12 months Certification: CE Place of Origin: Guangdong,China Brand Name: rawsun Model Number: RMC60 Application: 60KW peak power for the motor cooling type: water cooled high volt input range: 250-420VDC low volt input range: 9-30VDC peak efficiency: 99% Dimensions: 380*280*98mm IP grade: 67 Maximum working alitude: 3500m Max output current peak: 320Arms
GM18 final drives suitable for PC120-6, PC130-7 excavator. Also suitable for Doosan, Daewoo, sumitomo and so on more information pls contact with amy ,
